Wafer Level Reliability
-
Product
Probe Card
T90™ Series
-
The 90 mm tile was designed for mounting on a standard 4.5″ probe card holder for multi-site wafer level reliability testing. The 1.6 mm (0.062″) thick rails allow the chassis to slip into planarity adjustable probe card holders for most analytical probe stations.
-
Product
Probe Card
VC43™/VC43EAF™
-
VC43™/VC43EAF™ probe cards offer a larger format version of the popular VC20. In addition to saving time, another advantage of the modularity is the ability to leave the interface in place and simply install the VC43™ topside using Celadon’s twist and lock insertion tool which minimizes the possibility of triboelectric or interconnect issues that can occur during typical probe card changes. The VC43™ can be used for production parametric test, modeling, characterization, and wafer level reliability testing. Cards can be configured up to 104 probes in either single or dual layer with near vertical probes to minimize scrub lengths on pads allowing the VC43s to probe pads as small as 30 microns.
-
Product
Multisite Probe Card
T300 ButtonTile™
-
The Celadon T300™ probe cards are designed for long-term, multi-site, high-density wafer level reliability or burn-in tests up to 400°C. In today’s economic environment, conventional reliability data is needed quickly while eliminating the cost, electrical stress, and delay of parts packaging while maintaining a wafer performance map.
-
Product
Probe Card
VC20E Series
-
The 20mm VC20 is a highly adaptable probe card solution for a wide variety of tests including Modeling & Characterization, Wafer Level Reliability or Parametric Test. It can be easily combined with different interfaces to create modular probe cards supporting Keithley, Keysight or other custom tester platforms. Probes can be configured in either single or dual layer.
-
Product
MPI Automated Probe Systems
-
MPI Advanced Semiconductor Test
MPI’s 200 mm and 300 mm automated probe systems are dedicated and designed to address current and future requirements for all facets of Device Characterization for Modeling and Technology/Process Development, Failure Analysis, Design Verification, IC engineering, Wafer Level Reliability as well as special requirements for MEMS, High Power, RF and mmW device testing.
-
Product
Semi-Automated Probe Stations
SPS 2600, SPS 2800, and SPS 12000 Series
-
The SPS 2600, SPS 2800, and SPS 12000 Series systems are MicroXact’s semi-automated probe stations designed to be flexible and easy to use when performing high productivity device characterization, wafer level reliability testing and failure analysis. These semi-automatic probe station systems are designed to support manual and semi-automatic probing of up to 200mm wafers.
-
-
Product
Wafer Level Test Handler
Kronos
-
Wafer level test handler for 6/9DOF sensors with real stimulus. Very high UPH capacity and the lowest cost of test (COT). KRONOS is one of the only wafer level test solutions for motion sensors with real stimulus.
-
Product
Reliability And Durability Testing
-
Underwriters Laboratories Inc.
Our reliability and durability testing services provide an accurate assessment of how your product may perform under expected and unusual use. We can help you meet regulatory requirements, gain actionable knowledge about the anticipated life cycle of your products and identify design flaws that have adverse effects on a product’s reliability and durability.
-
-
Product
Wafer Prober
Prexa
-
The latest fully automated 300mm wafer prober. The system offers excellent productivity and advanced functions, contributing to KGD (known good die) testing for advanced packaging.
-
-
Product
Wafer Test
-
Silicon Turnkey Solution, Inc.
Most foundries provide wafers already probed to a set of DC parameters at room temperature to ensure they meet a basic subset of the package-part specification. Beyond this basic set of tests, more rigorous testing is often needed to meet specifications requiring die to be 100 percent probed, identify and segregate devices with higher performance levels and guarantee that parts will perform to a certain specification level.
-
-
Product
Wafer Inspection System
AutoWafer Pro™
-
AutoWafer pro is our most advanced ultrasonic equipment for detecting defects in bonded wafers in a production environment, providing fast, high-resolution scanning of 200mm and 300mm bonded wafers.
-
Product
WAFER MVM-SEM
E3300 Family
-
The E3310 is a WAFER MVM-SEM* for next generation wafers, supporting 1Xnm node process development and volume production at the 22nm node and beyond. With its high-speed carrier system employing a dual arm vacuum robot, and low-vibration platform to improve measurement accuracy, the E3310 delivers high throughput and performance for wafer measurements. Its multi detector configuration and unique 3D measurement algorithm also enable stable, high-accuracy measurement of 3D transistor technologies such as FinFET. The E3310 makes a significant contribution to reducing process development turnaround time and improves productivity for next-generation devices.
-
Product
Wafer Analysis Systems
Tropel®
-
Corning Specialty Materials has a long heritage of providing solutions to semiconductor equipment manufacturers. The Tropel line of wafer analysis equipment enables measurement of wafer substrates from 2” to 450mm regardless of material type and surface finish.
-
Product
Wafer Test Solutions
-
Wafer Test Solutions has established leadership positions in developing and deploying application-specific test solutions for MEMS devices, offering wafer and frame probing stations suitable for R&D, Wafer Sort, and Final Test. We offer state-of-the-art solutions to test environmental and motion sensors in wafer and other advanced packages.
-
Product
Level Switches
-
Omega can meet your level measurement requirements by offering switches of various technologies including capacitance and conductivity, tuning fork, ultrasonic, optical, and rotating paddle switches.
-
Product
Wafer Probe Heads
-
WLCSP test is the applying final test conditions at Wafer Level. WLCSP testing is driven in lowering the cost of test of devices through economical methods of manufacturing and testing.
-
Product
Level Measurement
-
In continuous level measurement, the level of a medium in a tank or silo is detected with the help of different measuring methods and converted into an electronic signal. The level signal is either displayed directly on site or incorporated into a process control or management system.
-
Product
Wafer Inspection Machine
IV-W2000
-
The IV-W2000 is a wafer inspection machine that features on-the-fly scanning and inspection as well as automatic handling of 6/8/12-inch wafers. With the option to have a Chinese language UI, this machine is also known for being intuitive and user-friendly.
-
Product
Laser Diode Reliability Burn-In / Life-Test System
58602
Test System
Chroma 58602 is a high density, precision multi source measurement Unit (SMU) module with temperature control and exchangeable interface developed for burn-in, reliability and life test of optoelectronic components including laser diodes, VCSELs, VCSEL Arrays, silicon Photonics, photo-diodes and other similar components.
-
Product
Silicon & Compound Wafers
-
Compound semiconductors are undergoing a major expansion addressing many new applications and using various materials such as SiC, GaN, GaAs and others, to improve the performance of new devices in several segments such as Power and Face Recognition.
-
Product
Wafer Probers
-
Devices to align probes to test the electrical properties of IC chips or TEGs (Test Element Groups) formed on wafers. The vast options available will meet various needs, from research to mass production.
-
Product
Level AFM
-
Is a flexible Atomic Force Microscope for scientists. It offers a wide range of modes, sophisticated spectroscopy options and the programming of user defined experiments. Besides standard options found in Anfatec's other AFMs, the level AFM allows to add Anfatec's full range of AFM options, such as KPFM, closed loop operation, automated sample motion, acoustic enclosure, humidity and temperature control ... Each instrument is adapted to the user's specific needs.
-
Product
Portable Wafer Probe Station
PS-5026B
-
High Power Pulse Instruments GmbH
The PS-5026B is a rugged portable wafer probing solution which has been designed for high reliability, compact size and minimum cost.
-
Product
Wafer Inspection System
INSPECTRA® Series
-
INSPECTRA® series meet the requests of 100% automatic inspection with high speed and high specifications from front-end to back-end of semiconductor processing. INSPECTRA® series are wafer inspection systems with high speed and high sensitivity. Our original "Die-to-Statistical-Image" comparison method achieves the target defects detection controlling process variation and overkill.
-
Product
Reliability Solutions
RT-300
-
RT-300 is a customizable ecosystem of connected insights, which empower plants and teams to proactively identify maintenance needs, make smarter decisions and keep machine performance and profitability at optimum levels.
-
Product
Wafer Thickness Measurement System
MPT1000
-
Laser based Wafer Thickness and Roughness Measurement System designed by Chapman Instrument Inc., USA and OEM by Creden Mechatronic Sdn Bhd. A non-contact measurement system measures several parameters in a single system. (wafer & tape thickness, roughness, TTV, bump height, bow and warp measurements)
