Headers
-
Product
IButton
-
Advantech iButton® devices are available for a number of different functions and supplied drivers and SDK. The DPX®-series boards have a GPIO header used to connect to one-wire or two-wire devices, which is a flexible multi-purpose interface.
-
Product
MAX31855 K-Type Thermocouple Sensor Breakout
SEN-30001-K
-
Breakout board for the MAX31855K digital thermocouple interface IC. Measured temperature range is -270C-1372C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.
-
Product
SparkFun USB Type A Female Breakout
-
This simple board breaks out a female USB type A connector's VCC, GND, D- and D+ pins to a 0.1" pitch header. If you want to add a USB to your project, but don't want to put up with soldering tiny connectors, this is the board for you.
-
Product
Digital Interface Boards
Model 4863 OEM
-
* 114514 Board has same digital capability as the 4863 described above with GPIB IO.* GPIB interface header includes GPIB address switch input signals.* Use with any IC GPIB Connector/Address Switch Assembly.* Uses 9-32 Vdc power.* 114515 Board has same digital capability as the 4863 described above with GPIB and Serial IO.* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any IC GPIB Connector/Address Switch Assembly or with a 114597 Serial Connector Kit.* Uses 9-32 Vdc power.
-
Product
Framegrabber
FastX-APU
-
The FastX-APU framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX-APU, is a two thirds length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex FPGA before being sent to the PCIe (X4) Gen 2 switch to the host or the AMD APU.
-
Product
Interface for the Multimode, multiprotocol Excalibur 8000 Family of Carrier Boards, Providing a Complete Solution for Developing & Testing MIL-STD-1760 Interfaces
M8K1760Px(S)
-
The M8K1760Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M8K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1760Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.In addition, Checksum, SRQ bit and Header Words are supported on each channel, as well as, error injection (BC and RT modes) and error detection (all modes).Each M8K1760PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The M8K1760Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application
-
Product
Micro Power, Header Insert, Receiver/ITA, SIM, Right Angle, 2 Pos, 2 Slot
510181103
SIM Insert
This header insert contains 2 right-angle micropower contacts and is designed for soldering directly to a PCB as part of the Infinity Connector system. It is used in the 90 Series SIM Module and occupies 2 of the 34 slots in this module.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
NI TB-2642B Terminal Block for NI 2532B as 1-Wire 16x32 Matrix Topology Without Column Protection Resistors
782385-05
Terminal Block
The TB-2642B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2642B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2642B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Female, 2m
40-971B-200-2m-MF
Cable Assembly
This male rear exit to ribbon cable 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers. It can also be used with Pickering 50-Pin Ribbon cable connector blocks.
-
Product
NI TB-2642B Terminal Block for NI 2532B as 1-Wire 16x32 Matrix topology With Column Protection Resistors
782385-06
Terminal Block
The TB-2642B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2642B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2642B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
CB-50 I/O Connector Block with DIN Rail Mounting without cable
776164-90
Terminal Block
50-Pin Male IDA to 50-Pin Female Screw Terminal, DIN Rail, Terminal Block - The CB-50 provides 50 screw terminals for connection to I/O signals from your 50-pin NI data acquisition devices. The CB-50 includes one 50-pin header for direct connection to 50-pin cables. It features a protective plastic base and hardware for mounting on a DIN Rail.
-
Product
Interface for Two Dual-Redundant 1760 Channels
EXC-1553PCMCIA/Px-1760
-
This credit card sized interface supports up to two dual redundant 1760 channels and is compatible with all common variations of MIL-STD-1760 providing a wide range of features normally found only on full size testers. Each channel of the EXC-1553PCMCIA/Px-1760 operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. The card supports Checksum, SRQ bit and Header Words as well as error injection and error detection. The card’s small size and compatibility with notebook computers make it the perfect solution for performing system simulation of the MIL-STD-1553 bus, in the lab and in the field.The EXC-1553PCMCIA/Px-1760 card is supplied with C drivers, including source code, Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
52x LVDS Module
LVDS-MOD5
-
Curtiss-Wright Defense Solutions
The LVDS-MOD5 high density LVDS I/O module offers the benefits of simplified cable connectivity by using two digital I/O headers suitable for ribbon cables. The LVDS-MOD5 LVDS I/O module can be used for a mixture of 2.5V and 3.3V input and output signals depending upon the VCCO settings on the FPGA on any particular I/O bank.
-
Product
UltraZed PCIe Carrier Card for UltraZed-EG System-on-Module
AES-ZU-PCIECC-G
-
The UltraZed PCIe Carrier Card supports the UltraZed-EG System-on-Module (SOM), providing easy access to the full 180 user I/O, 26 PS MIO, and 4 PS GTR transceivers available from the UltraZed-EG SOM via three Micro Headers. Two 140-pin Micro Headers on the carrier card mate with the UltraZed-EG SOM, connecting 180 of the UltraZed-EG Programmable Logic (PL) I/O to 2 Digilent Pmod™ compatible interfaces, FMC LPC slot, LVDS Touch Panel interface, push button switches, DIP switches, LEDs, Xilinx SYSMON, and clock oscillator.
-
Product
Smart GPIB Serial Interface Board
Model 4816
-
* Provides GPIB-to-serial and RS-232-to-RS-485 conversion path for serial devices with RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
Product
Talon 3.6 GS/sec Ultra Wideband RF/IF Rugged Portable Recorder
Talon RTR 2729A
-
- Video: A Quick Look at RTR 2729A Talon Rugged Portable Recorder- Designed to operate under conditions of shock and vibration- Portable system measuring 16.0" W x 6.9"D x 13.0" H- Lightweight, just less than 30 pounds- Sample rates up to 3.6 GHz in single-channel mode- Sample rates up to 1.8 GHz in dual-channel mode- 12-bit A/D, with 16- and 8-bit packing modes- Capable of recording RF/IF frequencies to 1.75 GHz in single-channel mode- Capable of recording RF/IF frequencies to 2.8 GHz in dual-channel mode- Real-time sustained recording rates of up to 4.0 GB/sec- Windows® 7 Professional workstation with high-performance Intel® Core™ i7 processor- Up to 61.4 terabytes of SSD storage to NTFS RAID solid state disk array- SystemFlow® GUI with Signal Viewer analysis tool- Optional file headers include time stamping and recording parameters- Optional GPS time and position stamping- Optional 10-36 VDC power supply
-
Product
1553 to Ethernet Converter
eNet-1553
Ethernet Interface
eNet is a small, rugged 1553 to Ethernet appliance/converter (~200 grams and about the size of a 4 stub coupler) and offers the same advanced BC, mRT and BM functions as our cards. In addition, eNet can provide an additional independent BM mode to auto bridge (transmit) 1553 messages on user defined IP/UDP packet header. The appliance can also auto-load setup images for fast auto start-up, which would be ideal for simple RT applications that wouldn’t even need an API interface (just a standard UDP interface – usually through simple socket programming).
-
Product
ArgoBot Kit
ROB-00001
-
The ArgoBot Full Kit is a fully assembled robot and controls development platform. It is based on the Digilent chipKIT WF32(TM), a WiFi enabled development platform, and configured for LabVIEW targeting. Most importantly ArgoBot was designed with FIRST Robotics Competition teams in the front of our minds! Named after the FRC Team 1756 mascot, Argos, the ArgoBot development platform includes a fully-assembled, ready to drive mini WiFi enabled robot (about 8" x 5" x 4"), as well as tons of FRC controls tutorials and example code (LabVIEW VIs). Features included on the ArgoBot will look very familiar to anyone who has worked with National Instruments products (Compact RIO and RoboRIO) in the past. This includes three 5V Digital I/O modules (with jumpered pull-ups), three 5V analog inputs, and an I2C header. Example VIs have been streamlined to enable a 1-click configuration style to accelerate your development process. We also added a 2-channel motor driver that is used to supply the ArgoBot drive motors. Our ultimate goal is that everything you can build, control or implement on ArgoBot can be easily leveraged on your FRC bot! Complimenting its many electrical features, ArgoBot is easy to work with and easy to maintain. The chassis is a polycarbonate (the extremely tough stuff that is easy to drill and modify but easily takes bumps and bruises without cracking) case that is fully intact - meaning that ArgoBot doesn't just come with a case... it is a case! Clean-up and organization is simple - just close the case and turn off the power switch.
-
Product
Power Interface Board 6U, 1 PSU connector with AC pins
106PIBM601-9001R
-
The PIB 6U 1 slot has one power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
GPIB Parallel Interface
Model 4803
-
* 4803 Board provides 40 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual GPIB headers support connections to a GPIB Connector/Address Switch Assembly or to a GPIB Flat Ribbon Cable Assembly.* Optional Relay Driver board drives 24-40 relays.
-
Product
Miniature 8-channel photon counter
id150 SERIES
-
Intended for large-volume OEM applications, the id150-1x8 is the only multichannel solid-state single photon detector on the market. It consists of a CMOS silicon chip packaged in a standard TO8-16pin header with a transparent window cap. The chip combines 8 in-line single photon avalanche diodes that can be accessed simultaneously for parallel processing. square in center-to-center A fast active quenching circuit is integrated within each pixel in order to operate each diode in photon counting regime. The chip is mounted on a printed circuit board on top of a single-stage thermoelectric cooler (TEC). A thermistor can be used to measure the temperature of the chip. Only two low power supplies of +5V and -25V are needed for operation in photon counting mode. The fast active quenching circuit leads to a dead time of less than 50ns per channel. An outstanding timing resolution of less than 60ps allows high accuracy measurements.
-
Product
Module for VME & VXI Systems
EXC-4000VME/xx / EXC-4000VXI/xx
-
The EXC-4000VME/xx and EXC-4000VXI/xx cards for VME & VXI systems supports up to eight dual redundant MIL-STD-1760 channels using the M4K1553Px(S)-1760 module and is compatible with all common variations of MIL-STD-1760 (A, B). Each channel can operate simultaneously as a Bus Controller and up to 32 Remote Terminals and as a Triggerable Monitor. In addition, Checksum, SRQ bit and Header Words are supported on each channel.
-
Product
3U VPX Power Interface Board VITA 62
106PIBC301-0000R
-
3U Convection Cooled VPX Power Interface Board, VITA 62 compliant. Power Interface Boards (PIBs) facilitate the use of pluggable power supplies and headers with the power section of the backplane.
-
Product
96/48/24-CH Opto-22 Compatible Digital I/O PCI Cards
PCI-7296/7248/7224
Digital I/O Module
ADLINK"s PCI-7296/7248/7224 are high-density parallel digital I/O boards with 96/48/24 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCI-7296/48/24 can utilize the Opto-22 external devices. The PCI-7296/7248/7224 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCI-7296/7248/7224 provides 4/2/1 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCI-7296/7248/7224 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCI-7296/7248/7224 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
Product
NEXT GENERATION RADIO PLATFORM
INTEGRA S
-
Integra S is an unbelievably light, energy efficient carrier-grade system that exemplifies an outstanding return on smart engineering - the synergy of high competence in radio electronics and materials science. Slip-fit design allows integration with existing high performance antenna systems or integration with 2+0 aggregation setups for up to 954 Mbps Full Duplex capacity without header compression. Gigabit Power over Ethernet (PoE) port defies simple installation, while dual SFP slots allow for fiber optic installation – giving the user ultimate flexibility in cable design.
-
Product
Serial to Relay Interface Boards
Model 2364 OEM
-
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Serial interface header includes RS-232 and RS-485 signals. * GPIB interface header includes GPIB address switch input signals.* Includes 50-pin mating relay connector and serial header connector.* Optional 115750 Terminal Board for easy connections without soldering.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel.
-
-
Product
Universal LightProbe Sensor Six-Pack
S6P
-
The Universal LightProbe Sensor Six-Pack provides a compact and efficient way to install six Universal LightProbe Sensors in a single space-saving unit. The convenient installation provides two standard circuit board header connectors, enabling the use of standard ribbon cable connections for the Universal LightProbe Sensors’ output. A single power and a single ground wire is all that is needed to connect as many as six Sensors. The Sensor Six-Pack will accommodate any combination of the pre-programmed Universal LightProbe Sensor models, which can then be paired with a wide variety of Fiber-optic Probes to customize for a specific test. For example, the Penta Sensor can be combined with “Trident” Fiber-optic Probes to test 18 LEDs.
-
Product
Arduino CAN Shield
IFB-10003-IWP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
