Headers
-
Product
PCB Adapter, ITA, QuadraPaddle, 192 Position, To PCB-Mounted 6x32-Pin Ribbon Cable Headers
510151125
PCB Adapter
PCB Adapter, ITA, QuadraPaddle, 192 Position, to PCB-Mounted 6x32-Pin Ribbon Cable Headers
-
Product
Ribbon Cable Headers
DINterm64
-
Ribbon cable headers are commonly used with VME compatible hardware. Ribbon cable is difficult to connect to other hardware, especially if multiple destinations are involved. The DINterm64 converts from 64 pin ribbon cable to a 64 pin terminal strip. Discrete wires are easily connected with the screw locks on the terminal strip.
-
Product
PCI Card
EXC-8000PCIe104/xx
-
The EXC-8000PCIe104/xx card for PCI/104-Express systems supports up to four dual redundant 1760 channels using the M8K1553Px(S)-1760 module and is compatible with all common variations of MIL-STD-1760 (A,B). In addition, Checksum, SRQ bit and Header Words are supported on each channel.
-
Product
Cable Assembly Crypto / Tape
-
The Cable Assembly Crypto / Tape provides a method of interconnecting the IP-Crypto and IP-Tape from the carrier to the PCI Bezel [rear IO] when installed into a PCI machine. Most IP Carriers have 50 pin headers suitable for ribbon cable in use for the IP Module IO. The headers are located on the carrier and internal to the chassis. Interconnecting to the outside world can be an issue.
-
Product
BME680 Environmental Sensor
28061
-
Raise your project’s environmental awareness with the BME680. The Bosch Sensortec BME680 Integrated Environmental Unit combines a gas sensor with air pressure, humidity, and ambient air temperature sensing functions within a single package for high performance air quality measurement. Parallax Inc. places the BME680 on a compact PCB with a 6-pin male header. This capable sensor does not have to be difficult to use. The BME680 is supported by BlocklyProp visual programming as well as C libraries for the Propeller multicore microcontroller. Code for other controllers is available from the Bosch Github repository.
-
Product
3U VPX Power Interface Board VITA 62
106PIBC301-0000R
-
3U Convection Cooled VPX Power Interface Board, VITA 62 compliant. Power Interface Boards (PIBs) facilitate the use of pluggable power supplies and headers with the power section of the backplane.
-
Product
SparkFun MicroView
USB Programmer
-
The MicroView is the first chip-sized Arduino compatible module that lets you see what your Arduino is thinking using a built-in OLED display. This USB programmer connects directly to the MicroView and lets you not only program the module, but use it to interface with your computer, Rapsberry Pi, or other USB device. The programmer has both male and female headers which allow it to be plugged into a MicroView module and a breadboard at the same time, making prototyping quick and easy.
-
Product
Digital Interface Boards
Model 4863 OEM
-
* 114514 Board has same digital capability as the 4863 described above with GPIB IO.* GPIB interface header includes GPIB address switch input signals.* Use with any IC GPIB Connector/Address Switch Assembly.* Uses 9-32 Vdc power.* 114515 Board has same digital capability as the 4863 described above with GPIB and Serial IO.* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any IC GPIB Connector/Address Switch Assembly or with a 114597 Serial Connector Kit.* Uses 9-32 Vdc power.
-
Product
DIP Header with Coined Contacts
Series 600
-
DIP Headers with Coined Contacts. Aries offers a full line of DIP headers, available with either coined or screw machine contacts. Consult Data Sheet No. 12035 for screw machine contacts. Snap-on, protective covers are available for all sizes shown below and accommodate .125 [3.18] to .750 [9.05] component heights. Consult Data Sheet No. 12033 for protective covers.
-
Product
Si1145 UV / Ambient Light / Proximity Sensor
SEN-36002
-
SEN-36002 is a highly integrated carrier board designed for the Si1145 UV, Ambient Light and Proximity sensor IC from Silicon Labs. This sensor has 100mLUX resolution, and has a dynamic range of 1 LUX to 128 kLUX with IR correction. This means that whether your application is indoors in poor lighting conditions or outside in full sunlight, this sensor has you covered. In addition, we added a high power LED (150mA max, 20 degree) to take full advantage of the proximity sensing capability of this IC - something you won't see on most competitive carrier boards. Integration is easy with 4 x 4-40 sized mounting holes at the corners of the PCB and signal translation to handle interface voltages from 3V to 5V. The board is interfaced via an I2C interface and function pins have been broken out to a 0.1" pin header. The INT pin is also broken out for interrupt capability.
-
Product
High Definition Audio Daughter Board with Line-in, Line-out and Mic-in
DB-Audio2
-
- Realtek ALC262 High Definition Audio codec- Three jacks: line-in, line-out and mic-in- 5x2 pin header for cable connection to external audio header on SBC- 4-pin header interface for CD audio output
-
Product
TB-2676, Ribbon, 100 V, PXI Module Multiplexer Terminal Block
779535-01
Terminal Block
Ribbon, 100 V, PXI Module Multiplexer Terminal Block - The TB-2676 features ribbon cable headers that help you access all channels of the PXI-2576 Multiplexer Switch Module. You can use the TB-2676 to configure the 16 banks of 4x1 2-wire multiplexers included with the PXI-2576.
-
Product
Serial Parallel Interface
Model 2313
-
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Separate headers for RS-232 and RS-485 signals. * Optional 2313 Flat Ribbon Cables mount DE-9 male or female connectors on the rear panel. * Optional Relay Driver boards with 64 or 128 Relay Drivers.
-
Product
Tool, Press Kit, i2 PCB Headers
910121199
Press Kit
Tool, Press Kit, i2 PCB HeadersAids in pressing fit pins into the header.
-
Product
Pod with Four Test Access Ports for 5v or 3.3V TTL Thresholds
JT 2137
-
The JT 2137 pod remains a popular choice for DataBlaster controller installations that require a compact signal conditioning pod embedded within a test fixture. The JT 2137 features four test access ports which together may be set for 5v or 3.3V TTL thresholds, although additional plug-in adapters are available that allow alternative thresholds to be set on a TAP by TAP basis (contact your local sales office for details). The 20-way 0.1″ IDC TAP headers comply with the standard JTAG Technologies 20-way pin-out and provide the additional flash programming controls Read/Busy and AutoWrite.
-
Product
Interface for the Multimode, multiprotocol Excalibur 8000 Family of Carrier Boards, Providing a Complete Solution for Developing & Testing MIL-STD-1760 Interfaces
M8K1760Px(S)
-
The M8K1760Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M8K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1760Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.In addition, Checksum, SRQ bit and Header Words are supported on each channel, as well as, error injection (BC and RT modes) and error detection (all modes).Each M8K1760PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The M8K1760Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Male, 2m
40-971B-200-2m-MM
Cable Assembly
This male rear exit to ribbon cable 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers.
-
Product
VTAC, Insert, Receiver/ITA, SIM, Pass-Thru, 8 Pos, 1 Slot
610151103
SIM Insert
VTAC, Insert, Receiver/ITA, SIM, Pass-Thru, 8 Pos, 1 Slot VTAC inserts are reversible and can be used as a Receiver or ITA insert.VPC's revolutionary high speed VTAC insert contains 8 gold-plated, self-aligning contacts and is designed to reduce crosstalk. With a data transfer rate of more than 12.5 Gbps per differential pair and a cycle life of over 150,000, VTAC has set the standard for high speed interconnect solution requirements. Sold in individual quantities.Use with VPC's right angle VTAC insert (p/n 610151104) or VPC's vertical header (p/n 610151107) to connect directly to a PCB.
-
Product
Digital Cable
Digital Cable
The Digital Cable models include a variety of industry-standard front- and back-end connectors, such as 68-pin VHDCI, 68-pin D-SUB, and flying lead options. Some models can connect digital instruments with other accessories to break out cable signals for direct access. Others provide flying leads that plug directly into any 0.1 in. header connector.
-
Product
Emulates Winbond W78ERD2
FE-WRD2
-
* Emulates Winbond W78ERD2 * 62K Code Memory * Real-Time Emulation * Frequency up to fmax at 5V * Windows Debugger For C/C++ And Assembler * 44-PLCC Emulation Header * Target Board and Programmer Included * RS-232 or USB Interface * 64K C/ASM and 8K C++ Included
-
Product
NI TB-2640B Terminal Block for NI 2532B as 1-Wire 4x128 Matrix Topology Without Column Protection Resistors
782385-01
Terminal Block
Screw Terminal, Ribbon, 4x128, 1-Wire PXI Module Matrix Terminal Block - The TB-2640B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 4x128 matrix. You can directly connect the TB-2640B to the front panel I/O connectors … of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2640B also provides optional isolation resistors to protect the reed relays from capacitive loads.This 782385-01 card does NOT have 100 Ohm protection.
-
Product
Screw-Terminal & Power Adapter Board - DC-coaxial-jack connectivity for 1 or 2 External VDC Power Supplies
TE3202
-
- Provides DC-coaxial-jack connectivity for 1 or 2 external 48 VDC power supplies- Provides screw-terminal connectivity for all sense, return, & output lines- May be directly connected to the HD-DB15 on the TE3200 front panel, or extended with a standard VGA extension cable.- Provided header pins for jumpering sense & return lines to channel output & return lines.- Provides a 2-pin header for jumper configuration with only one externally supplied 48VDC input (but, halves the maximum output current)
-
Product
MAX31855 T-Type Thermocouple Arduino Shield
SEN-30004-T03
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino.Each order comes with one board and a set of four female, long extension, headers that can be soldered to the board. If stacking two of these modules on top of each other, please order both a Ch 0-3 and a Ch 4-7 board, as well as an additional set of headers for stacking. We're working on sourcing even longer headers, but the ones currently available are not long enough to stack as-is (they need to be double-stacked).The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or MegaNote: we also offer a universal version of this board in a smaller for factor, the SEN-30003-T.FeaturesType-specific, miniature-sized vertical thermocouple connectors (vertical flat blades, see pics)Measures four (4) thermocouple channels, full extended range.Boards are stackable. Up to 8 thermocouple channels may be connected to an Arduino.14-bit SPI interfacePlugs directly into an Arduino Uno or Mega form factor with built-in voltage level translation on-board.Standard Arduino female headers required for easy configuration, one set included with order (1-6x1, 2-8x1, 1-10x1 0.1" female stackable headers), not soldered on.Detects shorts to GND or VccDetects open thermocoupleOther versions available (K, J, and T stocked). Contact Customer Service to place a custom order.Mounting holes for 4-40 sized screwsConnections are spaced for 0.1" pin headerDesigned, manufactured, tested and shipped from the USA The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
Product
Signal Module, Receiver, QuadraPaddle, 192 Position, Right Angle Contacts For Custom PCB Mounting (510 150 130 And 510 109 315)
510150152
Receiver Module
This kit has everything you need to attach a VPC Receiver Module to a custom designed PCB. This includes the right angle header (P/N 510 109 315) and the Receiver Module (P/N 510 150 130).
-
Product
Module for VME & VXI Systems
EXC-4000VME/xx / EXC-4000VXI/xx
-
The EXC-4000VME/xx and EXC-4000VXI/xx cards for VME & VXI systems supports up to eight dual redundant MIL-STD-1760 channels using the M4K1553Px(S)-1760 module and is compatible with all common variations of MIL-STD-1760 (A, B). Each channel can operate simultaneously as a Bus Controller and up to 32 Remote Terminals and as a Triggerable Monitor. In addition, Checksum, SRQ bit and Header Words are supported on each channel.
-
Product
Development System
FE-W7
-
* Emulates Winbond W77xxx or W78xxx Microcontrollers * 125K Code Memory * Real-Time Emulation * Frequency up to fmax at 1.8V to 5.5V * Wide Supply Voltage Support * MS-Windows Debugger For C And Assembler * Emulation Headers for PLCC, QFP and DIP * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
Fibre Channel PXI Express Test & Simulation Instrument
PXIe-FC4
-
Avionics Interface Technologies
3U PXIe form factor will fit into any PXIe or hybrid slot - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Triggering and Filtering - Error Injection on any Header or Payload Parameter - Data Capture to on-board memory or disk file - Live Capture and Current Value Monitoring - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Supports HS-1760E applications, including AS5653, AS5625, and AS5627fcXplorer Windows-based FC Simulator and Analyzer Test Software
-
Product
Interface for Two Dual-Redundant 1760 Channels
EXC-1553PCMCIA/Px-1760
-
This credit card sized interface supports up to two dual redundant 1760 channels and is compatible with all common variations of MIL-STD-1760 providing a wide range of features normally found only on full size testers. Each channel of the EXC-1553PCMCIA/Px-1760 operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. The card supports Checksum, SRQ bit and Header Words as well as error injection and error detection. The card’s small size and compatibility with notebook computers make it the perfect solution for performing system simulation of the MIL-STD-1553 bus, in the lab and in the field.The EXC-1553PCMCIA/Px-1760 card is supplied with C drivers, including source code, Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
MAX31855 T-Type Thermocouple Sensor Breakout
SEN-30001-T
-
Breakout board for the MAX31855T digital thermocouple interface IC. Measured temperature range is -270C-400C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.
-
Product
GPIB Serial Interface
Model 4804B
-
* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals. * Functions as a GPIB-to-Serial Interface (G-Mode) or as a Serial-to-GPIB Controller for a single device (S-Mode).* Over 600 Kbytes/second GPIB data transfer rate.* Transparent data transfer.* GPIB Address can be set by SCPI commands, by an external rocker switch or by a serial command.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
