Headers
-
product
SparkFun Rotary Encoder Breakout
Illuminated (RG/RGB)
This is a clever little breakout board for both the RGB and R/G illuminated rotary encoders. On one side, it breaks out all of the RGB pins to standard, breadboard friendly, 0.1" headers. Turn it over and it has a footprint for the R/G version! Simply solder an encoder down to the board and you're ready to add illuminated input to your next project.
-
product
Interface for Two Dual-Redundant 1760 Channels
EXC-1553PCMCIA/Px-1760
This credit card sized interface supports up to two dual redundant 1760 channels and is compatible with all common variations of MIL-STD-1760 providing a wide range of features normally found only on full size testers. Each channel of the EXC-1553PCMCIA/Px-1760 operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. The card supports Checksum, SRQ bit and Header Words as well as error injection and error detection. The card’s small size and compatibility with notebook computers make it the perfect solution for performing system simulation of the MIL-STD-1553 bus, in the lab and in the field.The EXC-1553PCMCIA/Px-1760 card is supplied with C drivers, including source code, Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
product
Signal, Module, Receiver, QuadraPaddle, 480 Position, Fully Loaded With Twin Female Contacts And Round Posts (610138200 And 610138117)
510150135
QuadraPaddle modules are molded on .1” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based mass interconnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .1” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
product
Shelf Manager Carrier/Mezzanine Board fix-mounted for CompactPCI
064-754
Set of Shelf manager mezzanine board installed on the fix mounted carrier board. The fix mounted carrier board provides all interfaces via headers for easy access and can be used directly inside of your system platform.
-
product
NI TB-2641B Terminal Block for NI 2532B as 1-Wire 8x64 Matrix topology With Column Protection Resistors
782385-04
The TB-2641B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x128 matrix. You can directly connect the TB-2641B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2641B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
TB-2630B , Screw Terminal, Ribbon, PXI Module Multiplexer Terminal Block
781687-01
The TB-2630B provides the necessary routing to configure the PXI-2630B PXI Multiplexer Switch Module as a single, dual, or quad 1-, 2, or 4-wire multiplexer. You can directly connect the TB-2630B to the front panel I/O connectors of the PXI-2630B. The NI TB-2630B features ribbon cable headers to connect signals to the PXI Multiplexer Switch Module as well as screw terminals for trigger input and trigger output signals.
-
product
VME 16-channel Differential to Single-Ended Signal Converter
V1250
The V1250 is a 16 channel differential to single ended signal converter in a 1-unit wide VME 6U form factor. It provides differential inputs (34-pin 2.54 mm header, Zdiff = 100 Ω) and single ended outputs (coaxial LEMO, Rout = 50 Ω).
-
product
SparkFun TRRS 3.5mm Jack Breakout
TRRS connectors are the audio-style connectors that you see on some phones, MP3 players and development boards. TRRS stands for "Tip, Ring, Ring, Sleeve," which reflects the fact that, unlike a standard stereo connector, this actually has three conductors and a ground. Some devices use the extra conductor for a microphone (like hands-free headsets) or to carry a video signal (like in some MP3/MP4 players). This breakout board makes it easy to add a TRRS jack to your prototype or project by breaking out each conductor to a standard 0.1" spaced header.
-
product
FMC Module
SMT-FMC510L
Sundance Multiprocessor Technology Ltd.
The SMT-FMC510L is an FMC module with a low pin count connector (LPC). It is primarily designed to attach to the EMC2-DP FMC PCIe104 carrier board and provide analogue video and serial interfaces. Connectivity is via BNC connectors on the main FMC PCB, BNC connectors on an adaptor PCB, and two 20-way latching DIL pin headers. The adapter PCB is optional and only required if interfaces other than analog video are needed.
-
product
1-, 10-, 40-Gigabit Ethernet Rugged Rackmount Recorder
Talon RTR 2755
- Designed to operate under conditions of shock and vibration- Records gigabit, 10-gigabit or 40-gigabit Ethernet streams- Removable shock- and vibration-resistant SSDs perform well in vehicles, ships and aircraft- TCP and UDP protocols- Copper or optical interfaces- Aggregate recording rates to 4.0 GB/sec- 4U short 19-inch rugged rackmount PC server chassis- Windows® Server 2016 workstation with high-performance Intel® Core™ i7 processor- Up to 122 terabytes of storage to NTFS RAID solid state disk array- Multiple RAID levels of 0, 1, 5, and 6- SystemFlow® GUI with Signal Viewer analysis tool- C-callable API for integration of recorder into applications- File headers include time stamping and recording parameters- Optional GPS time and position stamping- Optional 1836 VDC power supply
-
product
Power Interface Board 3 HE, 2PSU-Steckverbinder
106PIBM302-0000R
The PIB 3U 2 slot has two power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
product
DIP Program Header
Series 675
DIP Program Headers. Aries DIP programmable headers offer unusual versatility for programming within the header itself. They can be individually programmed using cutters or Aries programming tool, Part No. T-675, available separately, to remove the interconnecting sections. Consult Data Sheet No. 22002 for Aries programming tool.
-
product
PICMG 1.3 Full-size CPU Card With LGA1151 8th Gen Intel® Core™ I7/i5/i3, Xeon® E, Pentium® Or Celeron® Processor, Intel® C246/Q370/H310, SATA 3.0, USB 3.1 Gen1/Gen2, Dual LAN And DVI-I
SHB150
The SHB150 is based on the latest LGA1151 socket 8th generation Intel® Core™ processors (code name: Coffee Lake) and Intel® C246, Q370 or H310 chipset. The SHB150 features multiple I/O options and high-speed transfer interfaces as well as superior graphics capability (Intel® HD Graphics), making it an ideal solution for smart factory automation. The Intel® Core™-based full-size SBC, SHB150, comes with two 288-pin DDR4-2666/2400 Long-DIMM sockets with up to 32GB of system memory. The PICMG 1.3 single board computer has a maximum of six SATA-600 ports supporting software RAID 0/1/5/10 for data redundancy. It also has one M.2 Key M 2280 SSD slot with a PCIe x4 interface. The SHB150 with the Intel® HD Graphics brings a true high definition visual experience with triple display configurations (Intel® C246 or Q370) via DVI-I and DisplayPort (header) ports. Moreover, the Intel® Coffee Lake-based SHB150 supports optional Trusted Platform Module (TPM) 2.0 for optimum security, Intel® Active Management Technology (Intel® AMT) 12 for remote management, as well as Intel® vPro™ technology. The industrial single board computer provides significant advantages to customers in the fields of machine vision and industrial automation operations
-
product
Triple Balanced High IP3 Mixers To 3500 MHz
Pulsar Microwave Corporation features a high performance series of triple balanced mixers which offer superior IP3 performance. Optimized to cover specific bands (such as Cellular, PCS, LAN), a +10 dBm LO drive level results in a typical IP3 of +21 dBm, while +17 dBm and +23 LO drive levels result in typical IP3 readings of +30 and +35 dBm respectively. Provide us with your exact frequency ranges and power levels and we will be happy to guarantee an IP3 specification for your application.These high IP3 mixers are available in a number of packaging styles including 8-pin relay headers, TO5 & TO8 cans, flatpacks and connectorized housings. However, the most popular configuration is our miniature surface mount packages which are ideal for large volume applications and can be supplied on tape and reel to utilize automated pick and place assembly techniques.
-
product
Smart GPIB Serial Interface Board
Model 4816
* Provides GPIB-to-serial and RS-232-to-RS-485 conversion path for serial devices with RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
product
6TL-3X INLINE Header Conveyor 765 mm Length
AQ580
- PCB up to 600mm length 400 mm width- Programmable transfer speed up to 1 m/s- Automatic Previous/Next speed adjustment- 2D Code reader w/automatic positioning- Pre-wired for second 2D Code reader- Automatic width setting- PC for line management w/UPS with 20” monitor and keypad in adjustable position arm- 24 Ports PoE Switch- Power inlet rack with current protections and line safety relay- Top cover and door w/safety contacts inhibiting line modules while active- Mechanisms self-test- Width auto-adjustment and cyclic width- Non-contact electronic stop of the PCB- 4U Free on the 19” Rack- Interfaces SMEMA 9851 y IPC-HERMES 9852- CE certified
-
product
NI TB-2644B Terminal Block for NI 2532B as 1-Wire Dual 8x32 Matrix or 2-Wire 8×32 Matrix topology With Column Protection Resistors
782385-10
The TB-2644B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 8x32 or 1-wire dual 8x32 matrix. You can directly connect the TB-2644B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2644B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
Process Analyzer, Vent Master™ Series
Parkers Vent Master is designed to isolate the analyzer from fluctuating outlet pressures by controlling the pressure of the collection header and pumping the effluent sample gases into the fluctuating system
-
product
Serial Parallel Interface
Model 2313
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Separate headers for RS-232 and RS-485 signals. * Optional 2313 Flat Ribbon Cables mount DE-9 male or female connectors on the rear panel. * Optional Relay Driver boards with 64 or 128 Relay Drivers.
-
product
S-100 Bus, Vectorbord Plugbord
8804
VECTOR Electronics and Technology, Inc.
100 Gold plated edge contacts (50 each side)on 0.125"(3.175mm) centers. Voltage/Ground buses. Zig-Zag buses. I/O mounting area for ribbon cable header. Row and column legends provided. S-100 Form Factor.Pin 1 and 51 committed to power. Pin 50 and 100 committed to ground.
-
product
CableEye® HV-Rated QuickMount™ Housing for CAMI Connector Boards
CBH2
CAMI Research Inc. (Acton, MA) has released a High-Voltage (HV)-rated QuickMount housing (CBH2) for its CableEye® automation-ready, cable and wire harness testing systems. As a free-standing, quick-release board fixture, it allows users to connect CAMI’s test interface boards to the 64-pin headers of any expansion module - even at some distance. The housing may be used with any CableEye model and is rated to 2100 Vdc / 1500 Vac.
-
product
Multi Functional VME Logic Module
MDGG-16
The MDGG-16 is a single wide 6U VME multi functional FPGA based delay logic and timing module which provides often needed functions as gate generator & pulse generator, logic fan in - fan out, coincidence register and scaler / pre-scaler. The module has 16 LVDS/ECL inputs and 16 ECL outputs on pin headers and 2 NIM inputs as well as 4 NIM outputs (Lemo), which are free configurable in regards to their functionality.
-
product
PCI Express Card with 96 DIO and Counter/Timers
PCIe-DIO-96C3
This is a x1 lane PCIe, 96 line digital input/output card with counter/timer capabilities designed for use in high I/O density application requirements. I/O connections are made via four 50-pin header connectors. The card is 12.25 inches long (312 mm) and may be installed in any full-length slot that has x1 lane PCIe.
-
product
Power Interface Board 6U, 2 PSU connectors with AC pins
106PIBM602-9001R
The PIB 6U 2 slot has one power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
product
Current Transformer Testers
Vanguard Instruments Company, Inc.
Performs CT excitation, current-ratio, polarity, and phase angle testsMeasures insulation resistance and winding resistance of the CT seconday windingsMeasures the CT's secondary burdenTest record header information including company, substation name, circuit ID, manufacturer, CT serial number, operator name, and test record-commentsBuilt-in 4.5-inch wide thermal printerPlot Multiple Saturation CurvesStores up to 128 CT test plans and 140 test records internallyUSB, Bluetooth, and USB Flash drive interface
-
-
product
NI TB-2641B Terminal Block for NI 2532B as 1-Wire 8x64 Matrix Topology Without Column Protection Resistors
782385-03
The TB-2641B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x128 matrix. You can directly connect the TB-2641B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2641B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
100 Pin 1.27mm Pitch Micro-D Connector & Cable Accessories
The 100 Pin 1.27mm Pitch Micro-D connector is used on many products to provide a high density 1A connector solution that is suitable for use to 150Vdc If you would like to develop your own cabling solutions, we offer mating connectors and connector hoods that allow you to create either your own cable based solutions, or a PCB header solution. Connector Blocks directly terminate the module connector and convert the connection to arrays of screw terminal blocks, or you can select to use a remote DIN rail mounted breakout to terminate the cables at the end of a cable assembly. You can also try our Cable Design Tool to graphically design a customized cable assembly.
-
product
52x LVDS Module
LVDS-MOD5
Curtiss-Wright Defense Solutions
The LVDS-MOD5 high density LVDS I/O module offers the benefits of simplified cable connectivity by using two digital I/O headers suitable for ribbon cables. The LVDS-MOD5 LVDS I/O module can be used for a mixture of 2.5V and 3.3V input and output signals depending upon the VCCO settings on the FPGA on any particular I/O bank.
-
product
SparkFun Atmospheric Sensor Breakout
BME280 (with Headers)
The SparkFun BME280 Atmospheric Sensor Breakout with Headers is the easy way to measure barometric pressure, humidity, and temperature readings all without taking up too much space. Basically, anything you need to know about atmospheric conditions you can find out from this tiny breakout. The BME280 Breakout has been designed to be used in indoor/outdoor navigation, weather forecasting, home automation, and even personal health and wellness monitoring.
