Showing results: 1276 - 1290 of 3178 items found.
-
A100c -
Celtek Electronics Ltd
This single-range, RF power measurement instrument is designed to operate in the 2.45 GHz range. Used by field service engineers, engaged in the repair and maintenance of commercial and domestic microwave heating equipment, its primary function is the detection RF microwave energy leakage.
-
A100p -
Celtek Electronics Ltd
This single-range, RF power measurement instrument is designed to operate in the 2.45 GHz range. Used by field service engineers, engaged in the repair and maintenance of commercial and domestic microwave heating equipment, its primary function is the detection RF microwave energy leakage.
-
Aim-TTi
RF spectrum analyzers with a true hand-held format.Models from 1.3GHz to 6.0GHz
-
RF-LAMBDA Inc.
RF Amplifier including AGC functionality to maintain constant output power
-
RF-LAMBDA Inc.
RF Multiplexers supporting commercial communication bands to reduce antennas and cabling.
-
-
Aaronia AG
High-quality Splitter, Coupler and RF over Fibre Solutions. Made in Germany.
-
RF coupling -
Langer EMV-Technik GmbH
is used for the conducted measurement of the immunity according to IEC 62132-4.
-
Teledyne RF & Microwave
Teledyne RF & Microwave, a Business Unit of Teledyne Microwave Solutions (TMS), supplies catalog and custom RF and microwave amplifier designs for aerospace, defense, and industrial applications. These standard amplifiers, originally designed by Teledyne Cougar, provide both excellent stability and cascadability.
-
ISDB-T/Tb -
TestTree
Network operators:automate the tests of new transmittertemporary monitoring/investigation toolrebroadcasting receiver: RF to ASI or IPBroadcasters: off-air monitoring probe to validate the on-air contentTV/STB producers: automated tests against a professional receiverLabs: easy & simple access to live DTV sources via RF
-
TYPE HFX-1 -
National RF, Inc
The Type HFX-1 Modulation Monitor is an ancillary piece of equipment, which is used with narrow bandwidth, or older oscilloscopes to allow viewing of RF signals and particularly modulated signals as high as 55MHz. The equipment contains an RF signal source and a broadband mixing circuit which converts the high frequency signal to an intermediate frequency within the oscilloscope’s range. The frequency control dial is simply adjusted until the RF signal is viewed on the scope. BNC connectors are mounted on the rear panel to allow interconnect to the scope and RF probe. This product was previously called "oscilloscope frequency extender" and may be used to view other high frequency signals on older or narrow band scopes.
-
Adaura Technologies
RF leakage through Ethernet and USB cables can destroy even the best RF enclosures and chambers. The need for filtering in the ever congested RF environment requires special filters that can pass USB 2.0 and 10/100/1000 Mbps Ethernet signals and filter out unwanted higher frequencies such as cellular and WiFi. The Adaura Technologies USB/Gigabit Filters provide one GigE and one USB 2.0 pass-through connections while filtering out other RF up to 8GHz. It has a small form factor to allow easy installation. It is a most cost effective solution for a clean chamber set up. In a typical chamber, WiFi signals are reduced to <-100dBm with this filter installed.
-
RFFE -
Arasan Chip Systems, Inc.
Mobile phone radios have developed into highly complex, multi-band and multi-standard designs that often have multiple radio frequency (RF) signal chains. The MIPI Alliance Specification for RF Front-End Control Interface (RFFE) was developed to offer a common and widespread method for controlling RF front-end devices. The RFFE Master IP core typically resides in the RFIC in a mobile platform, and utilizes the RFFE bus to identify, program and monitor the registers in RF front end Slave devices through programmed IO. It is designed to support existing standards such as LTE, UMTS, HSPA and EGPRS, and is usable in configurations ranging from single Master/single Slave to multi-Master/multi-Slave.
-
ETL Systems Ltd
Most of ETL's sub-systems are designed to fit standard 19" racks. We produce RF distribution equipment for a wide range of applications in the RF chain. On satellite downlinks this is between the LNB and the modem or receiver; and on satellite uplinks it is between a modem and a BUC.Reliability, Resilience and RF performance are designed into all our equipment wherever possible. Scaleability and Adaptability also influence the design process.The main product families are shown below, with further selection of products via functionality and design.
-
Antenna Technology Communications, Inc.
The 402LZ is a outdoor/indoor mounted fiber optic transmitter for RF signals in the satellite L-Band or wider frequency range. It accepts a single RF input on coaxial cable and provides a single output for optical transmission. Up to four 402LZ’s may be installed in the ATCi Link4i chassis.