Showing results: 1921 - 1935 of 3183 items found.
-
DCZ-XXE/Y -
Elmika
The DCZ-XXE/Y directional couplers are used for extracting or introducing RF power flow in a transmission line withoutdistortion of signal characteristics. The directional couplers are available in 3, 6, 10, 15, 20 dB coupling values and30 - 35 dB minimum directivities*. 4-ports directional couplers are available in bi-directional (BDC4-XXE/Y) and dual-directional(DDC4-XXE/Y) configurations.
-
ERS -
Laplace Instruments Ltd.
The ERS is a comb generator that radiates RF continuously every 2MHz over the range 30MHz - 1000MHz. Each 2MHz peak is precisely measured during the calibration process with the ERS orientated both vertically and horizontally. These measurements are correlated against a 3m OATS such that any fully implemented CISPR16 site, measuring at 3m and using height scanning, will read the same.
-
Teseq AG
The GTEM cell is a frequency extended variant of the traditional TEM (Transverse Electro-Magnetic) cell. The GTEM cell is, in principle, a tapered coaxial line (offset septum plate), which is terminated by a combination of discrete resistors and RF absorbers to achieve a broadband match. Designed for EMC applications, calibration of antennas/field probes, test and measuring of mobile phones and screening measuring of material.
-
HD-500 -
Matrix Test Equipment Incorporated
The MATRIX Model HD-500 is a detector-amplifier designed to demodulate the low frequency amplitude modulations on any RF carrier over the range of 5 to 1500 MHz. These modulations are usually the undesirable result of the 50 or 60 Hz power source and are not necessarily sinusoidal. The unit is calibrated to the SCTE definition of hum modulation, which is the ratio of the peak-to-peak hum modulation to the peak of the carrier.
-
4500C -
Boonton Electronics
The Boonton Model 4500C is the instrument of choice for capturing, displaying, analyzing and characterizing microwave and RF power in both the time and statistical domains. It is ideal for design, verification, and troubleshooting of pulsed and noise-like signals used in commercial and military radar, electronic warfare (EW), wireless communications (e.g., LTE, LTE-A, and 5G), and consumer electronics (WLAN), as well as education and research applications.
-
BSC Filters
BSC provides full design and manufacture expertise in-house to offer high reliability mixed technology RF & Microwave modules such as Switched Filter Banks and typically covering from L band to X band. Typical applications include: Electronic Intelligence (ELINT), Electronic Warfare (EW), Direction Finding Receivers (DF), Radio Preselector, and band segmentation.
-
Pasternack Enterprises, Inc.
ISM and RFID bandpass filter PE8700 from Pasternack is part of our extensive in-stock RF components for sale. Our ISM and RFID band pass filter is manufactured with SMA connectors that are female and in a 4 section design. This 4 section SMA bandpass filter for ISM and RFID has an insertion loss of 1.500 dB and a maximum power of 5 Watts.
-
Pasternack Enterprises, Inc.
ISM and RFID bandpass filter PE8700 from Pasternack is part of our extensive in-stock RF components for sale. Our ISM and RFID band pass filter is manufactured with SMA connectors that are female and in a 4 section design. This 4 section SMA bandpass filter for ISM and RFID has an insertion loss of 1.500 dB and a maximum power of 5 Watts.
-
CAL-UFL-BAL -
MegiQ BV
The Balanced Calibration Kit is an interface kit for UFL and balanced VNA measurements. It contains SMA-UFL adapters and several adapters from SMA and UFL to balanced pinheaders. The UFL connector was introduced by Hirose as the U.FL connector and became very popular for connecting RF signals in consumer electronics. There are several varieties from other manufacturors and are also known as UMC or UMCC connectors.
-
Multiple Access Communications Ltd.
Building on MAC Ltd’s MONITOR product family, our CatchAll units combine these with additional functionality to realise RF receiver and transceiver products ready to be deployed in a wide range of real world applications. As well as being available pre-configured with standard application software, these units can also be supplied with application software developed specifically to meet your own requirements.
-
Teledyne RF & Microwave
With a 30 year heritage in YIG technology, Teledyne RF & Microwave has unsurpassed capabilities as your single source for YIG Oscillators and offers 'best in industry' low phase noise. Teledyne has a large, self-contained YIG manufacturing and R&D infrastructure that ensures continuous YIG innovations, including the industry's only YIG filter that "locks" to a desired signal.
-
Menlo Systems Gmbh
Our Timing Solutions allow the long-term stable distribution of a master RF or optical reference throughout a large-scale research facility with minimal added phase noise and drift (< 10 fs rms). Ideally suited for modern accelerator facilities, our solutions are fully customizable. We will work with you to make sure the system fits the requirements of your facility exactly.
-
11716A -
Keysight Technologies
Quickly and conveniently connect 1 dB step and 10 dB step attenuators together to achieve greater dynamic range with 1 dB steps. The Keysight 11716A interconnect kit contains a rigid RF cable, mounting bracket, and necessary hardware to connect any pair of Keysight 8494/5/6/7 attenuators in series. Attenuators must be ordered separately.
-
S3531 -
Saluki Technology Inc.
Saluki S3531 series RF spectrum analyzer is designed based on the concept “Smaller, lighter, easier” . S3531 series takes a small desktop space and easy to carry. Most of nowaday RF applications are in this band, like mobile communication (GSM, CDMA, LTE even low frequency 5G), WIFI (2.4GHz), remote control etc, so S3531 series is a good tool for the test, maintenance, R&D of these applications.
-
Teledyne Defense Electronics Relays & Coax Switch
Teledyne Relays' packaged SPDT Indium Phosphide Active RF Switches provide low insertion loss and high linearity, with bandwidths from DC up to 60GHz. These switches also maintain excellent signal integrity beyond 40Gbps, and have a very compact package size of 3mm x 3mm x 1mm. Teledyne's Active RF switches are ideal for test and measurement systems, microwave communication, and radar applications.