Showing results: 3031 - 3045 of 3183 items found.
-
ERAVANT
A weather resistant, quad ridged, dual polarized antenna feed designed for outdoor application that operates from 0.7 GHz to 4 GHz. The antenna offers 8.0 dBi nominal gain and a typical half power beamwidth of 68 degrees on the E-plane and 98 degrees on the H-plane. The typical side lobe level is -10 dB and the port isolation is 20 dB at center frequency, respectively. The antenna supports linear polarized waveforms and can form the circular polarized waveform if the two ports are fed with 90 degree phase differenced and equal amplituded signals. The antenna has four 0.20” holes for mounting. The RF ports of the antenna are equipped with two female SMA (F) coaxial connectors.
-
CB503 -
Teledyne Defence & Space
The need for tunable filter technology originates from the fact that high power communication systems and IED Jammer transmitters severely limit the use of tactical radio communication systems on the battlefield.This clash within the radio’s spectrum during tactical missions is often de-conflicted using fixed high Q, high power RF bandpass and bandstop filters installed prior to mission. This can limit operational effectiveness due to the potentially large number of fixed filters required within the allocated radio communication channels, which need be transported, stored in the field, and fitted by trained personnel. Many of these fixed filters centred within the octave wide tuning range could be replaced by a single high-Q tunable filter.
-
DG009-M1 -
Teledyne Defence & Space
Many advanced EW receivers, particularly those associated with ECM jamming systems, do not require the high resolution frequency information associated with a DFD or IFM based receiver. This is typically the case where a single pulse present within a broad frequency band is required to be detected and instantaneously down-converted to an IF band.TDS manufactures a range of Frequency Activity Detectors (FADs) also known as Activity Detection Units (ADU) which perform frequency measurement of an RF pulse and output data in as little as 15ns. The basis of these products is TDS’s ability to produce high performance broadband channelisers and integrated detectors. These devices are ideal for receivers which must operate in very high pulse density environments.
-
MR30 (30KHz~100GHz) -
Hangzhou Huatai Optic Tech. Co., Ltd.
MR30 series microwave wideband optical receiver, adopts waveguide intergrated PIN photodetector. Within 40KHz~100GHz bandwidth, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. MR30 series PIN photodetector products have unsurpassed high-power handing capability. In system application, they can pre-amplify the received optical power by EDFA, favorable responsibility, with high voltage out, avoiding the need for electrical amplification. They are suitable for testing and application in microwave opto-electronics and high speed lightwave area as well as 40Gb/s (OC-768, STM-256) high-speed communication system.
-
SFT3348C -
Hangzhou Softel Optic Co., Ltd.
SFT3348C is a high performance and cost-effective DVB-C modulator designed by Softel. It has 8 DVB-S2 tuner inputs, after multiplexing, scrambling and modulating process, then it gives 4 RF output. To meet customers’ various requirements, this device is also equipped with 128 IP input and 4 MPTS output over UDP and RTP. Its pluggable structure design greatly facilitates the change of modules as needed. Moreover, the four CAMs/CIs accompanied can descramble the programs input from 8 Tuner inputs. SFT3348C can be upgraded and controlled through network system, which allows it to be widely used in setting up digital broadcasting network and very adaptable to newly generation CATV broadcasting system.
-
MR21 (40KHz~18GHz) -
Hangzhou Huatai Optic Tech. Co., Ltd.
MR21 series microwave wideband optical receiver, adopts High linear PIN diode and Low noise pre-amplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 18Gb/s high speed communication system.
-
MR11 (40KHz~18GHz) -
Hangzhou Huatai Optic Tech. Co., Ltd.
MR11 series microwave wideband optical receiver, adopts high Sensitivity APD diode and Low Noise Preamplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s high speed communication system.
-
ADGM1304 -
Analog Devices Inc.
The ADGM1304 is a wideband, single-pole, four-throw (SP4T) switch, fabricated using Analog Devices, Inc., microelectro-mechanical system (MEMS) switch technology. This technology enables a small, wide bandwidth, highly linear, low insertion loss switch that is operational down to 0 Hz/dc, making it an ideal switching solution for a wide range of RF applications. An integrated control chip generates the high voltage necessary to electrostatically actuate the switch via a complementary metal-oxide semiconductor (CMOS)-/low voltage transistor-transistor logic (LVTTL)-compatible parallel interface. All four switches are independently controllable. The ADGM1304 is packaged in a 24-lead, 5 mm × 4 mm × 0.95 mm lead frame chip-scale package (LFCSP).
-
Talon RTR 2623 -
Pentek, Inc.
- Search and capture system using Sentinel™ Intelligent Signal Scanner- Captures RF signals up to 6 GHz- Capture and scan bandwidths up to 40 MHz- 30 GHz/sec scan rate- Selectable threshold triggered or manual record modes- 16-bit A/D with 75 dB SNR & 87 dB SFDR- Built-in DDC with selectable decimation range from 2 to 65,536- Portable system measuring 16.0" W x 6.9" D x 13.0" H- Lightweight, just less than 30 pounds- Storage capabilities to 30 TB- RAID levels of 0, 5, and 6- Windows® workstation with Intel Core™ i7 processor
-
Excelitas Technologies Corp.
Excelitas Capacitor Chargers are tailored to meet your exact needs by configuring modular platforms based on proven designs. Single-phase AC input designs are capable of up to 6 kW of output power and our three-phase designs provide up to 35 kW of output power. A modular design approach results in lower cost, higher reliability, and faster time-to-market. Typical applications for capacitor charging power supplies include flashlamp pumped laser systems (Nd: YAG, pulsed lasers, dye lasers, Intense Pulsed Light Systems (IPL) and aesthetic Medical Laser Systems, Medical Holmium YAG Laser), excimer lasers, pulsed UV curing and sterilization, radar and RF systems.
-
Panda Microwave Limited
Panda Microwave design, manufacture, and support a wide variety of Power Amplifier. RF amplifiers product line from Panda Microwave consists of low noise amplifiers, Power Amplifier Module and Solid State High Power Amplifier. Our Power amplifiers cover frequency range from 100MHz to 50GHz and used Thin-film Technology. Our low noise amplifiers have superior noise figure numbers and a variety of models. Gain block low noise amplifiers provide all around gain where noise is not critical. High power amplifiers system equipment is available with either manual or digital control interfaces, power capacities up to 100W pulse power.
-
787272-01 -
NI
The Ettus USRP X410 integrates hardware and software to help you prototype high-performance wireless systems and perform over-the-air signal generation and analysis. Additionally, the Ettus USRP X410 features a two-stage superheterodyne architecture with four independent transmitter and receiver channels. It also features a Xilinx Zynq Ultrascale+ RFSoC with programmable FPGA supporting the Open Source UHD tool flow as well as LabVIEW FPGA. With these features, the Ettus USRP X410 has the RF and processing performance for applications such as wireless communications prototyping, spectrum monitoring, and signals intelligence. The Ettus USRP X410 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) Reference Clock, which improves frequency accuracy and synchronization.
-
Model 8256 -
Pentek, Inc.
- Video: AOC 2021 Mercury's Model 8256 SOSA Aligned Dev. Platform and RFM3202 Microwave Transceiver- Video: Model 8256 3U VPX SOSA Aligned Development Platform, multi-vendor operation demonstration- Video: Model 8256 3U VPX SOSA Aligned Development Chassis- Developed in alignment with the SOSA™ Technical Standard- Ideal development platform for Pentek's- Model 5550 8-Channel A/D & D/A Zynq UltraScale+ RFSoC Processor - SOSA Aligned 3U VPX- Model 5553 8-Channel A/D & D/A Zynq UltraScale+ RFSoC Processor - SOSA Aligned 3U VPX- 8-slots provide space for a range of acquisition and processing boards- Optional rear panel RF and optical connections- Compatible with the Quartz product family
-
Talon RTR 2750 -
Pentek, Inc.
- Sixteen 250 MHz 16-bit A/Ds- Sixteen independently-configurable DDC decimations ranging from 2 to 65536- Sixteen independently-configurable DDC tuning frequencies- Capable of recording RF frequencies to 700 MHz- Capable of recording signals with bandwidths to 100 MHz- 8 GB/s real-time aggregate recording rate- 4U 19-inch rugged rackmount PC server chassis- Windows® 7 Professional workstation with high performance Intel® Core™ i7 processor- Front panel removable-SSD drives- Up to 61 terabytes of storage to NTFS RAID disk array- Multiple RAID levels of 0, 1, 5 and 6- SystemFlow® GUI with signal viewer analysis tool- Optional GPS time and position stamping
-
100G NRZ BERT -
Munich-Instruments GmbH
The C-BERT 2810-4 is a complete bit error rate tester dedicated for 100G Ethernet applications. The four independent channels enable an actual operating environment with traffic on all lanes. The simultaneous testing of 4 channels is much faster than testing each channel individually saving time and money. The BERT eye scan reveals low-probability events and shows the true performance of the DUT to aid troubleshooting. The high RF port density eliminates long cable length which degrades the signal at 25 Gb/s. The OS independent GUI is easy to install and enable remote control from everywhere. The complete and compact C-BERT is a powerful and cost efficient test solution for 100G Ethernet.C-BERT MI-PE2810-4 Product sheet_rev05.
