-
Product
Signal, Contact, ITA, TriPaddle, Round Post, PCB Mount
610110000
Signal Contact (ITA)
Primary mating contact 610110179. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAAVG Mating Force(lbs) 0.41Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 Cycles
-
-
Product
Test Case Generator
Hexawise
-
Use Hexawise to design better tests. Maximize test coverage with the minimum number of test cases. Find twice as many errors per tester hour. Manually-designed software test plans often omit combinations of functions and configurations that need to be tested. Hexawise leaves no gaps and ensures all important combinations get tested.
-
Product
Test And Product Engineering Services
-
Tessolve provide Test & Product engineering Solutions & services from simple Logic ICs, high-speed digital, RF, Analog, PMIC, Mixed-signal, MCU/MPU, MEMS, Image Sensors, Memory to complex devices like ASIC/ASSP, SoC / SiP devices that go into Automotive, IoT, Wearable, Wireless, Computing, Network / Fiber optics and other consumer markets. We also engage ourselves in providing test solutions for emerging technologies in the 2.5D / 3D space.
-
Product
MIPI Receiver Test Solution
M8085A
-
The M8085A is a software plug-in for M8070A Bit Error Ratio Test system software within the M8000 series of BER test solutions. The M8085A software plug-in controls either the M8190A or the M8195A Arbitrary Waveform Generators to create C-PHY or D-PHY standard compliant test signals. In addition it provides routines for calibration of all signal parameters and for all tests specified in the applicable Conformance Test Suite. Together with the additional available DUT control interface it is possible to read the BER of the receiver under test from the M8070A software and display the BER dependency from test parameters within the M8070A user interface.
-
Product
Primary Test Equipment
LET-2010-RD
-
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.
-
Product
SilverCreek SNMP Tests
-
Set up in less than five minutes - Windows or LinuxCustomize tests via Wizards, Script Generators, and moreAutomate operation with unambiguous test resultsIntegrate with other test harnesses and test toolsIncludes conformance, compliance, vulnerability, robustness, stress, and performance testingInvestigate failures and quickly resolve them with powerful diagnostic and analysis tools
-
Product
CAM/TRAC Test Kits
Series 41
-
The Series 41 dual well mechanical kits provide a test solution where Z axis and the testing of two PCA’s is required. These can be similar devices, or devices that are used together in a functional test. The Series 41 Kits have the same available features and options as the Series 40 Kits. (Limited sizes available.)
-
Product
EMI and EMC Test System
-
EMI receiver system. It is a main test system for EMI (Electro Magnetic Interference) testing. The EMI-9KB is produced by the full closure structure and strong electro-conductibility material, which has high shielding effect. Due to the new technology for the EMI Test System, it solved the instrument self-EMI problem.
-
Product
Furniture Test Equipment
-
chair seat drop impact durability testing machine for chair drop durability is used to evaluate the ability of the chair to withstand heavy and abusive impact forces on the seat. It can also to evaluate the ability of chairs to withstand fatigue stresses and wear caused by downward vertical force(s) on the seat. -
-
Product
Test Automation
-
Deployment ramping up pressure on the test organization to validate products in shorter test cycles. We have assisted Tier – 1 companies in the BFSI, Cloud Solutions and Communication domains to deploy highly efficient test strategies. Talk to our engineers to see how we can assist your business.
-
Product
Functional Test
-
A type of software testing that verifies a program's functions against its requirements, checking that the software works as expected by comparing the actual output to the expected output.
-
Product
Dynamic Component Test Systems
-
RedViking brings advanced engineering and proven implementation expertise to your next dynamic component test stand. We’ve designed entire fleets of multi-model and single-model test systems for new component development and production as well as military and commercial MROs. We have decades of experience building and implementing turnkey dynamic component test systems, and we’ll work with your teams virtually anywhere in the world.
-
Product
Test Chambers
-
Test Chambers: climate test chamber, climactic temperature test chamber, humidity seed chamber, medical stability test chamber, plant growth chamber, salt spray test chamber, temperature and humidity test chamber, UV test chamber, xenon test chamber, and more.
-
Product
Radio Testing
-
TRaC provide a complete and streamlined process to meet the radio testing, certification and approval requirements to take your radio product to market.
-
Product
High-Temperature Test Systems
-
HT-PEM (high-temperature polymer electrolyte membrane) technology represents a further development of PEM fuel cell technology. Unlike conventional PEM fuel cells, which operate at lower temperatures, HT-PEM fuel cells can reach temperatures of up to 200 °C.
-
Product
Fluke Test Equipment
-
Fluke Test Equipment includes electrical test equipment, environmental test equipment, mechanical test equipment and more. Fiberinthebox supply a large range of Fluke Test Equipment, such as Fluke Fluke NetTool Inline Network Service Kit, Fluke Networks AirCheck Wi-Fi Tester, Fluke Networks Cable Strippers, Fluke Power Meter, Fluke Power Analyzers.
-
Product
Plastics Testing Equipment
-
Dongguan Amade Instruments Technology Co., Ltd
Plastics testing equipment include a series of instruments intended to carry out testings of component analysis, formula analysis, performance determination, aging resistance test etc on various plastic materials and plastic products in accordance with ISO, ASTM, DIN, HB international standards. Mechanical & physical & chemical property testings include tensile strength, bending strength, friction coefficient, creep resistance property, tearing strength, shearing property, impact resistance property, compression performance, hardness, resilience property, fatigue strength, melt index, heat deflection temperature, melt viscosity, density, flammability characteristics, resistance to aging under UV, xenon, ozone, high/low temperature etc.
-
Product
RF/Wireless Test Fixtures
-
Test‐Head Engineering develops and manufactures RF Test Fixtures which allow the testing of RF and Wireless modules and components.
-
Product
Pulsation Testing Equipment
-
Parker's offering of pulsation testing equipment quantifies Square Root and Gauge Line Errors in natural gas orifice-flow measurement, identifying inaccuracies caused by compressor-induced pulsation and differential-pressure discrepancies
-
Product
Exchangeable Test Fixture
MA 2111/D/H/S-5
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 9,30 kg
-
Product
Loop Testing
-
Megger loop testers offer both traditional measuring techniques and state of the art “non-RCD Tripping” technology. Use these products to determine the prospective earth fault current, which is the maximum current able to flow in a phase-earth fault in an installation, and also to indicate the prospective short circuit current which is the maximum current able to flow in the event of a phase-neutral fault.
-
Product
Ozone Test Chamber
EKT-2001OZ-HCSLT
-
Designed and manufactured in accordance with ASTM D1149, ISO1431 & JIS K6259 standards. Providing precise and accurate ozone (OZ) concentration environment for rubber and polymer test. Widely applied to (1) Accelerated ageing research (2) Quality control and assurance tests and (3) R&D laboratory formula experiments for cracking resistance.
-
Product
Optical Test And Measurement
-
Any type of fiber optic interconnection requires its interfaces to be free of dust and scratches in order to reach the lowest transmission loss. Small, handheld and battery powered inspection tools are available from AMS Technologies for inspection of fiber optic connectors in the field as well as high resolution type microscopes suitable for use in a production environment for qualifying the endface preparation. Additional S/W tools can support the user in making a quick decision if a certain defect is acceptable or if the surface fault disqualifies it for further use. Small and lightweight test equipment for measurement of the transmitted power in an optical fiber is needed wherever technicians handle optical fibers. Our product portfolio comprises light sources for various wavelengths, power meters for the visible and infrared and integrated solutions for sources and meters as well as optical time domain reflectometers (OTDR) coupled with visible wavelength light sources for easy fault detection within a fiber optic link.
-
Product
Color Wheel Test Kits
-
The color discs use a visual comparison method (color matching) to determine concentration. Simply add reagents to the sample and turn the wheel until the sample matches the reference color. The concentration is displayed in a window.
-
Product
Test & Inspection
-
Our test and inspection products support maintenance, product quality testing, diagnostics, and quality control. The extensive range of products covers almost any application need you to have.
-
Product
ESD & Latch-Up Test System
-
Identify and help correct ESD and latch-up susceptibility issues on sensitive integrated circuit components prior to full-scale production with the Thermo Scientific™ MK.2-SE ESD and Latch-Up Test System. The MK.2-SE test system provides advanced capabilities to test high pin count IC devices to Human Body Model (HBM) and Machine Model (MM) ESD standards. The system’s pulse delivery design addresses wave form hazards such as trailing pulse and pre-discharge voltage rise, and performs Latch-Up testing per the JEDEC EIA/JESD 78 Method.
-
Product
Water Testing
-
Benchtop conductivity meter, benchtop dissolved oxygen meter, benchtop ion meter, benchtop multi-parameter water quality meter, benchtop water hardness meter, BOD meter, COD analyzer, conductivity tester, dissolved oxygen tester, multi parameter water quality analyzer, online conductivity controller, online dissolved oxygen controller, online pH controller, ORP tester, pH meter (benchtop), pH meters (portable), pH tester, portable conductivity meter, portable dissolve oxygen meter, portable multi parameter water quality meter, portable water hardness meters, salinity tester, TDS tester, TSS meter, trubidity meter, water activity meter
-
Product
Test System
4003 TLP+™
-
The Model 4002 TLP+™ test system was the first turn-key commercial TLP developed for the ESD industry and has remained the leader in the ESD square pulse testing field since this method was first introduced in 1989. This tester is the ultimate design and analysis tool for ESD protection circuits. It provides Pulse Curve Traces of circuit characteristics which simulate ESD tests. This allows you to see into a chip’s operation taking out the guesswork which speeds your design and minimizes lost time.
-
