-
Product
Massively Parallel Board Test System
I7090
-
The Keysight i7090 is a massively parallel board test system designed to help PCBA test engineers improve manufacturing efficiency while reducing costs. Unlike traditional in-circuit testers, the i7090 supports up to 20 In-Circuit Test cores in parallel, which means engineers can test multiple Units Under Test (UUTs) simultaneously without the need for multiple systems. This reduces scaling and infrastructure costs and frees up valuable testing space.
-
Product
LUTHER & MAELZERBARE AND LOADED BOARD TEST PROBES
SERIES LMP 60
-
MechanicalMINIMUM CENTERS: .100 (2.54)FULL TRAVEL: .160 (4.06)WORKING TRAVEL: .107 (2.72)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,35 mOHMS meanMaterials and FinishesPLUNGER: Heat treated berylliumcopper, 24 Kt gold plated over nickelBARREL: Nickel silver, 24 Kt goldplated over nickel
-
Product
THRU HOLEBARE AND LOADED BOARD TEST PROBES
SERIES 93
-
ElectricalMAXIMUM CURRENT: 7 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,35 mOHMS mean
-
Product
LUTHER & MAELZER BARE BOARD TEST PINS
SERIES LMP 78
-
Materials and Finishes MATERIAL: Heat treated beryllium copper FINISH: 24 Kt gold plate over hard electroless nickel
-
Product
RELIABILITY BOARD (Reliability Test Board)
-
The reliability test board is used for testing of HAST, THB, HTOL, BURN-IN, etc. It is a product that evaluates the environmental test and durability when applied to actual products such as lifetime test, high temperature, low temperature, high humidity and thermal shock
-
Product
SMT & THRU HOLELOADED BOARD TEST PROBES
SERIES 43
-
MechanicalMINIMUM CENTERS: .075 (1.91)FULL TRAVEL: .250 (6.35)WORKING TRAVEL: .167 (4.24)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 3 amps continuous at working travel, non-inductiveRESISTANCE: At 35 mA test current,30 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper or steel hardened to 55-60RC, both 24Kt gold plated over nickelBARREL: Nickel silver with 24Kt gold plated ID and OD over nickelSPRING: Music wire, 24Kt gold plated over nickel
-
Product
SMT & THRU HOLELOADED BOARD TEST PROBES
SERIES 33
-
ElectricalMAXIMUM CURRENT:3 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,20 mOHMS meanMaterials and FinishesPLUNGER: Heat treated berylliumcopper, 24Kt gold plated over nickelBARREL: Nickel silver with preciousmetal clad ID.SPRING: Music wire, silver plated
-
Product
LOADED BOARD TEST PROBES
SERIES-70
-
ElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35mA test current70 18 mOhms mean73 60 mOhms mean74 40 mOhms meanMaterials and FinishesPLUNGER: Heat treated beryllium copperor steel hardened to 55-60RC70 24Kt gold plated over nickel73 24Kt gold plated over nickel74 Rhodium plated over nickelBARREL: Nickel silver70 24Kt gold plated ID and OD over nickel73 No Finish74 24Kt gold plated ID and OD over nickel
-
Product
Control Board For Testing PCBs
TCC 1800
-
The TCC1800 Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via a galvanically separated USB interface. The TCC1800 is designed to work with positive voltages up to 24V. All inputs and outputs are protected against higher voltages however. The card provides basic IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, Serial (UART) and I2C interfacing.
-
Product
Quadruple Function Tester with Shielded HF Test Chambers
UTP 9011 RF
-
Circuit boards are the heart of all electronic devices. To ensure the reliable function of these boards, detailed tests are essential.Our board-level tester UTP 9011 RF works safely, quickly and cost-optimized at circuit board level. Our interchangeable adapters are particularly efficient in this system, with which you can even test different test items at the same time. The shielded NOFFZ HF test chamber always ensures consistently good results.
-
Product
Thermal Test Boards
-
Thermal Engineering Associates, Inc.
TEA offers a series of thermal test boards for package characterization and design comparison that conform to to the JEDEC JESD51 standards. The board family, referred to as the TTB-1000 series, consists of two different standard sizes designed to cover a wide range of package sizes. These boards, also referred to as test coupons, provide a well defined mounting environment, will withstand temperatures to 125 oC, and have lead lands terminated in eyelets to allow for hand-wired connection to the board edge contacts. The board mates with a dual 18-pin, 3.962 mm (0.156") pitch edge-card connector.
-
Product
MECHANICAL TEST FIXTURE KITS
TX-MT-SERIES
-
Test-X MT Series mechanical kits are an affordable solution to printed circuit board testing. With multiple configurations and available options, this product is sure to meet your testing needs. The MT Series features a hinged 3/8" FR4 probe plate, tooling holes for accurate drilling, and side handles for easy transportation.
-
Product
Boundary Scan Test
-
Boundary Scan is a very useful tool for quick, low-cost, re-usable powered-up test of an assembly for basic functionality. Because a fixture with test probes is not required, it is possible to have a working test available within hours or days, rather than weeks. Designers can receive rapid feedback on their prototype boards with tests that can be used again during production testing, as well as for device programming. Given power, ground and Tap port signals, tests can be written to assess the performance of the boundary scan enabled parts on an assembly and other parts on the boundary scan chain.
-
Product
Meter Test Board
MTB-3200
-
Run standard meter accuracy tests and complex meter accuracy tests under widely varying loading conditions with TESCO’s Meter Test Board (MTB-3200). TESCO’s Three Phase Meter Test Board (MTB-3200) is an innovative meter accuracy test system offering unsurpassed functionality and ease of use. All of the features needed to test meters today and tomorrow are standard.
-
Product
Electronic Testing Services
-
Printed Circuit Board Testing and Repair Services CM Wings Board Testing Inc. was founded in 1983. Its founding was a direct response to theneed for a truly customer service oriented facility for printed circuit board test and repair.
-
Product
Software & Hardware Interface
XJAPI
-
The XJAPI is a simple-to-use DLL Application Program Interface (API), designed to give you low-level access to the JTAG chain via either the XJLink or the PXI hardware, allowing easy integration with a wide range of other systems such as development/evaluation boards, test systems
-
Product
Calibration Pulse Processor
2401
-
TESCO’s Calibration Pulse Processor (Catalog No. 2401) adapts to any Next Generation three phase test board to directly calibrate with three independent single phase standards.
-
Product
Programming on-chip flash in your processor
XJDirect
-
XJDirect is an advanced and innovative method for programming the internal flash of your processor and implementing some aspects of board test through JTAG when traditional boundary scan techniques cannot be used.
-
Product
Dynamic Digital I/O With Per Channel Timing, Programmable Logic Levels And PMU PXI Card
GX5296
-
The GX5296 offers advanced dynamic digital I/O performance and capabilities in a single slot, 3U PXI format. The 32-channel, GX5296 features timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability to emulate and test complex digital busses for system, board or device test applications. Offering sub-nanosecond edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
Product
Digital Input Board
VME-1129
-
VME-1129 128-bit high voltage digital input board with Built-in-Test and input filter. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297), with the following mnemonics: A24:A16: D32/D16/D08 (EO): Slave:39/3D: 29/2D Form Factor: 6U
-
Product
Silicon Test & Yield Analysis Solutions
Tessent®
-
The Tessent product suite combines features of deterministic scan testing, embedded pattern compression, built-in self-test, specialized embedded memory test and repair, and boundary scan, as well as board and system-level test technologies. This comprehensive silicon test and yield analysis solution is built on the foundation of the best-in-class solutions for each test discipline
-
Product
PXI 8x SPST High Voltage Reed Relays
40-310-001
-
The 40-310/320 range of high voltage switching modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
Test Points, Tips, Probes, Jumpers and Clips
-
Nickel Plated Steel Alligator Clips. PTFE Insulated Terminals and Test Point Jacks. Circuit Board Test Jacks and Plugs. Color Coded PCB Mount Test Points, Loop Style with Plastic Base for Snap-In Mounting. Surface Mount Test Points on Tape and Reel.
-
Product
LXI High Voltage Matrix 2-pole 200x2
60-310-202
-
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
VME Test Extender 6U/220mm 64X w/o P0
116EXT6122-012XR
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
BARE BOARD TEST PROBES
-
Probe Technical DataMechanicalMINIMUM CENTERS: .100 (2.54)FULL TRAVEL: .160 (4.06)WORKING TRAVEL: .107 (2.72)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current60 18 mOHMS mean63 60 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper60 24 Kt gold plated over nickel63 24 Kt gold plated over nickelBARREL: Nickel silver60 24 Kt gold plated ID and OD over nickel63 No FinishSPRING: Music Wire, 24 Kt gold platedover nickel
-
Product
1149.6 Boundary Scan Feature, GTE 10.00p
K8213B
-
Keysight’s Interconnect Plus Boundary Scan 1149.6 feature enables all the tools required to develop and execute this test method on the board under test. Compared to the 1149.1 standards, the 1149.6 standards define test methods for the boundary scan devices that are designed with AC coupled signals or differential nets needed for high-speed operations of the device.
-
Product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
-
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
Product
FPGA Test System
DO-254/CTS
-
DO-254/CTS™ is a fully customized hardware and software platform that augments target board testing to increase verification coverage by test and satisfy the verification objectives of DO-254/ED-80. The target design runs at-speed in the target device mounted on the custom daughter board. The simulation testbench is used as test vectors to enable requirements-based testing with 100% FPGA pin-level controllability and visibility necessary to implement normal range and abnormal range tests. The FPGA testing results are captured at-speed and displayed using a simulator waveform viewer for advanced analysis and documentation.
-
Product
Solid Pins
-
Advanced Probing Systems, Inc.
APS produces electro-chemically machined pins in diameters between .020"-.040" in a variety of materials for use in various applications. These “large diameter pins” are used in various medical applications, industrial applications, board testing, LED & LCD test and as components in small tools. APS’s design services can help you select the optimal material from tungsten, beryllium-copper, Paliney 7® or various stainless steel alloys or work with the material of your choice. Pins can be produced with either a sharp or radius (rounded) tip. Tapers can be highly polished, slightly polished, matte or neutral in finish.
