Media Converters
-
Product
Lamp Converters
-
PeakTech Prüf- und Messtechnik GmbH
This AC / AC voltage converter is particularly suitable for use with halogen indoor lights and other low-voltage light sources that require an AC voltage source for supply. There is a safe galvanic separation between mains and low voltage according to the isolating transformer standard. This pre-assembled AC / AC converter is equipped with an overtemperature switch that cannot be reset.
-
Product
Frequency Block Converter
FBC
-
The FBC-XX-FB is a full band system can be built upon a Keysight N8975A Noise Figure Analyzer (NFA) or X Series Signal Analyzer with option N9069A. This system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device covering Ka, U, V, E, W bands (26.5-170 GHz), when used with an Agilent E8247C signal generator (or equivalent).
-
Product
Buck, Boost And Buck-Boost Converters
-
Renesas has many options for DC/DC converters, controllers and regulators with buck, boost and buck-boost topologies.
-
Product
DC/DC Converter 150 W
CQB150W-110S48
-
DC/DC converter with 150 W from Cincon | input ranges 43 - 160 VDC | output 48 V | operates in temperature from -40 to +105 °C | according to EN45545-2 fire and smoke
-
Product
Internet Streaming To UDP Stream Converter
ILG200
-
Mividi’s Internet Video Streaming to Local Broadcast Gateway (ILG200) converts the Internet video streaming using HTTP, RTMP and RTSP protocols to UDP streams for local broadcast. This product provides a simple solution for legacy CCTV network operators, such as cable and IPTV providers, to rebroadcast Internet streaming content.
-
Product
Transition Time Converters
-
These converters have been designed to convert the transition times of instruments with fixed, fast transition times, to slower, fixed transition-times (150 ps, 250 ps, 500 ps, 1 ns, 2 ns); hence reducing the signal bandwidth. All transition-times are between 10% and 90% of amplitude.The design of these converters ensures very low signal reflection far beyond the 3 dB point. Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications. The converters are fitted with two SMA connectors, one male, one female.
-
Product
- RS-485 to Fiber Optic Converter
Model 276A
-
FEATURES: Data Rate to 1 MBPS; ST Connectors; DB-25 Connector; Half-duplex operation; Extends distance of RS-485 network to 6,600 ft (2 km) on multimode fiber cable. The Model 276A provides the capability of transmitting an RS-485 signal via a fiber optic link.
-
Product
DC/DC Converter 2 W
REM2-1505D
-
DC/DC converter 2 W from Recom | input ranges 13.5 - 16.5 VDC | outputs +/-5 V | operates in ambient temperature from -40 to +95 °C
-
Product
725-Watt (28VDC input) DC/DC Converter, SOSA™ Aligned, 3U VPX
VPX55HS
DC Converter
NAI’s VPX55HS-31 is NAI's latest +28 VDC Input, VPX DC/DC Converter. The VPX55HS was developed in alignment of the SOSA™ Technical Standard and is capable of handling up to 725 Watts of output power. It plugs directly into a standard 3U VPX chassis with a VITA 62 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
DC/DC Converter 192 W
HP2540-9TB1G
-
DC/DC converter with 192 W from Bel Power Solutions | input ranges 16.8 - 137.5 VDC | two outputs at 15 V | operates in temperatures from -40 to +71 °C | provides 10 ms hold up time | 20 mm heatsink included
-
Product
Synchro/Resolver to Linear DC Converter
DC Converter
NAI offers a variety of Synchro/Resolver Converters that continuously transform Synchro or Resolver inputs into digital form. These solid-state modules provide resolution to 16-bit and accuracy to 19.8 arc-seconds, and are error-free up to the maximum specified tracking rate. They are transformer-isolated and operate over a frequency range from 47 Hz to 10 kHz. The modules are specifically designed for rugged defense and industrial applications.
-
Product
Analog-To-Digital Converters
-
Teledyne e2v has been innovating data converter technologies for over 20 years and offer a range of analog-to-digital converters that feature:Latency as low as 5 nsUp to 4 channels at microwave frequenciesLowest noise vs. performance on the market at microwave frequenciesThe cutting-edge technology packed into Teledyne e2v's data converters allow our customers to significantly simplify designs with licence free, standard and customized solutions.
-
Product
5VDC Sensor Converter, 12VDC, 25mA
ENVIROMUX-S5VDC
-
External RJ45 device monitors up to two linear DC sensors, 0VDC ~ 5VDC. Output for each sensor: 12VDC, 25mA. Connector: Screw Terminal, 8-position. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Includes Mounting Hardware. Powered by ENVIROMUX-2D/5D/16D. MTBF: 1,956,288 hrs. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
Product
File-based Broadcast Media QC Software
Vidchecker
-
idchecker is an easy to install Windows software application for PCs/servers. It removes the labor intensive tasks of manually checking conformance by eye and hand, the need to check video/audio compliance with waveform monitors and audio loudness meters, and to manually correct levels with video processing amplifiers, and other tools. Supports sub SD, SD, HD, 4K and mixed workflows
-
Product
DC-DC Converters
-
TDK-Lambda is a global supplier of DC-DC converters with a broad range of power levels. The commercial off the shelf power solutions encompass industry standard board mounted products to chassis mount configurations for the Industrial, Healthcare, Information and Communications Technology (ICT), and Avionics and Defense markets.
-
Product
Serial Converter
USB-COMi
-
The USB-COMi is a USB to RS485 serial converter. It allows easy serial port expansion without requiring IRQ, DMA, or I/O port resources. The converter allows the user to easily and economically connect RS485 devices to a host using USB. The RS485 communications standard is used by DGH sensor based data acquisition modules and many industrial control devices.
-
Product
RS-232 to RS-422 Optically Isolated Interface Converter
Model 265
-
FEATURES: Eliminates Ground Loops; 19.2 KBPS at 2 Miles;TD and RD Indicators; Use in Pairs as Double Isolated Short Haul Modems; Use in Pairs as Double Isolated Short Haul Modem. Total isolation between RS-232 based systems and RS-422. Unique circuitry allows the RS-422 port to withstand surges exceeding 10 kilovolts.
-
Product
BCD to Binary Converter
BCD250
-
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
Product
RF Mixers & Frequency Converters Overview
-
Up and down conversion is often used because waveform generation in a transmitter is less expensive at lower frequencies and the dynamic range of analogue-to-digital converters in the receiver is higher at lower frequency.
-
Product
Voltage Converter
99539C
-
The model 99539C is an 8 channel wide dynamic range voltage to frequency converter of modular design.
-
Product
Centralized Media Workflow Management
VIA Xsquare
-
VIA Xsquare provides a single entry point for production teams to transform, orchestrate and monitor media files as they move through the live workflow all the way from ingest to shared storage and distribution. By centralizing all media processing job requests in a single web interface, reducing transcoding needs, and enabling SDR/HDR conversion on the fly, VIA Xsquare maximizes productivity and offers higher visibility of all workflow processes. Its high-availability design and flexible architecture provide users with a scalable system to manage workflows between EVS systems, third-party storage, and non-linear editing (NLE) systems.
-
Product
DC/DC Converter 3.5 W
REM3.5E-4824S/R6/A/SMD
-
DC/DC converter with 3.5 W from Recom | input ranges 36 - 75 VDC | output 24 V | operates in ambient temperature from -40 to +95 °C | SMT package
-
Product
DC-DC Converters
-
The standard range of DC-DC Converters contains units with power outputs from 40W to 5kW. Small footprints, high conversion efficiencies and floating outputs are common throughout the converter range. For users that require the highest reliability a number of our converter families demonstrate MTBF figures of 750,000 hours. Our most rugged converter designs are capable of operating in ambient temperatures as low as -40°C and as high +80°C.
-
Product
DC/DC Converter 1000 W
CRS-1000-6478-C
-
DC/DC converter with 1000 W from Premium | input ranges 28.8 - 60 VDC | output 24 V | operates in temperatures from -25 to +70 °C | designed according to EN50155
-
Product
6-Channel VME Optical-to-Electrical Converter
V730
-
The V730 is a six-channel logic-level optical-to-electrical converter, packaged as a single-width, 6U VME module. When used with compatible Highland optical transmitter modules, the V730 provides fast, low-jitter, EMI-proof distribution of pulses, triggers, and precision timing signals.
-
Product
ARINC 818 to HDMI Converter
-
The ARINC 818 to HDMI converter is a rugged standalone module available in half-length PCIe form factor used for ARINC 818 to HDMI conversion, HDMI to ARINC 818 conversion, 2x ARINC 818 Switch as well as ARINC 818 Duplicator/Splitter. It is a video Converter module designed with Kintex-7 FPGA, using an Analog device Video Encoder, and Decoder to provide video interfacing requirements.
-
Product
O/E Converter
TIA-1200
-
The TIA-1200 optical to electrical converter is a convenient battery powered wideband detection system for fibre optic applications. With a typical bandwidth of DC to 12 GHz (min. 10 GHz), it accurately provides an electrical replica of the optical signal presented to it. It is intended to drive a 50 ohm cable terminated in its characteristic impedance.
-
Product
Frequency to Current Converter
DAT4540R
-
The Frequency to Current converter DAT4540R is a signal conditioning din rail mount converter which converts a pulse input to an analog output equal to the set range which is selectable from 0.1 Hz up to 20 KHz. The DAT4540R also provides 2 relay outputs and a transistor output. The input can be from a Tacho, TTL, PNP transistor or from any Namur standard. The DAT4540R provides a Voltage or Current output that is isolated from the power supply and input.
-
Product
DC/DC Converter 100 W
CTS-120-6865-D
-
DC/DC converter with 100 W from Premium | input ranges 14.4 - 30 VDC | output 5 V | operates in temperatures from -25 to +85 °C | designed according to EN50155
-
Product
MACC Protocol Converters
-
Introducing the ultimate solution for effortless communication between different protocols - our state-of-the-art MACC II protocol converter.This powerful device allows you to easily translate messages between MIL-STD-1553, ARINC-429, Ethernet, Serial and more, ensuring compatibility and reliability in your aerospace and defense systems.With its advanced features and user-friendly interface, our protocol converter is the perfect solution for aircraft manufacturers, avionics designers, and military system integrators. It offers accurate and efficient data transfer, making it ideal for use in a wide range of applications such as aircrafts, ground vehicles, and naval vessels.Our protocol converters, both rugged, to withstand harsh environments, and standard, for the lab, are fully customizable to meet your specific needs. Its compact and lightweight design makes it easy to install and integrate with other systems.Don't let communication protocol limitations hold you back - Upgrade your systems today and experience the difference!
