LED Test
See Also: Flicker Analyzers
-
Product
Flight Control System Test Platform
Test Platform
The Flight Control System Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of Flight Control Systems (FCS) of both commercial and military aircraft. The system simulates control surface activities from multiple combinations of rudder, flaps, elevator, aileron, and engine controls to the FCS. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
Product
LED Driver Automatic Test System
ATE-2
-
•This system includes 2 groups (left and right); the 2 groups can work in turn, so that to improve the work efficiency. For example, if the left is on working, then the right can make wire connection. •It can test 4 LED drivers input and output at one time. •The equipment can connect with electronic load and LED load, the two difference loads can be fast switch under the control of computer. •Enable to print out the series number and parameters of sub-quality products by working with a micro-printer, •Enable to achieve the bar-code record function by working with a bar-code scanner. •The test report can be saved as Excel file for consult, statistic and analysis purpose. •Good software interface to freely choose the difference parameters combination, so that to meet different demands. All the parameters can set limit, and with the quality analysis function.
-
Product
Goniophotometer Test System For Led Lamp
LCG-1680B
-
Shenzhen Chuangxin Instruments Co., Ltd.
Design according to IEC61341the test method of central luminous intensity and beam angle for reflecting light, this instrument can be used to test the cross section luminous intensity distribution curve, central luminous intensity and effective beam angle of LED assembled luminaries and LED lens system with diameter less than 180mm.
-
Product
LED Illumination Systems
pE-100
-
The pE-100 series is a mercury-free family of compact and simple to use LED illumination systems which can be configured to deliver light directly to a microscope, or via a liquid light guide or multimode fiber. Systems can be specified at any one of 20 different LED wavelengths. Operation is by a remote manual control pod with instant on/off and intensity control from 0-100%. Remote control is available via a TTL trigger.
-
Product
Test Instruments
Test Instrument
Test instrumentation from COTS to custom, including VXI, PXI and LXI-based platforms.
-
Product
SparkFun LED Driver Breakout
LP55231
-
The SparkFun LP55231 LED Driver Breakout is a self-contained solution for developing and deploying the nine-channel I2C LED controller. Remarkably simple, the breakout is equipped primarily with just the LP55231 LED controller IC, plus three RGB LEDs. It also features pads and jumpers for replacing the onboard LEDs with external ones, and configuring the I2C bus, which allows you to daisy-chain up to four LP55231s. This breakout drives the LEDs using Pulse Width Modulation (PWM), so it is well-suited for variable intensity and color-mixing applications!
-
Product
S2 Unicolor Sensors
ULP-S2 SCI/V
LED Sensor
The Universal LightProbe S2 Unicolor Sensor is designed for the intensity test of any single one of the five main LED colors (blue, green, yellow, orange, and red) plus white and Infrared (700nm to 1,000nm). Implemented in a unique and customizable 2-Part solution, the S2 Unicolor Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times:<10mS capture time; 65mS overall response time; intensity output of correct color only.Fiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
Product
LED Drivers
-
Highly efficient LED drivers provide optimal performance in general lighting applications and in LED backlighting systems for large flat display panels.
-
Product
LED Driver Aging Rack
LEDRACK-100W192P
-
• Application range: LED driver and multi channel driver power aging. It has equipped with computer operation and monitor system. The working condition can be set by the computer, and the computer will record real time data to do statistical analysis. • The parameters of load can be set freely on the software, to monitor the real time voltage, current, and power etc • Load mode: CC, CV, CR, CP, and LED • Aging Control System includes: ON/OFF control signal output; Signal of relay switch control; K type thermocouple temperature acquisition • The channels are parallel connected under arbitrary load mode, which can allow product power expansion • The LED Driver Aging rack will design according to customer’s LED driver power and aging quantity per time • Automatic current switching function (optional) • AC power meter to measure modules, and test power input characteristics (optional) • Temperature monitoring function at product zone (optional) • PWM dimming and two sets of logic control signal function (optional)
-
-
Product
Test System Optimized for High Volume Production Testing of Integrated Circuits
ETS-364 / ETS-600
Test System
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture. The test system offers separate floating resources for each site, improving site isolation and measurement accuracy coupled with digital instrumentation enabling the most efficient, high-volume testing available. The system supports up to 240 analog pin channels, and offers 133 MVPS digital vector rate with up to 128 digital pin channels. Eagle's scalability includes the ability to double the capacity of an ETS-364, providing more than 480 analog pin channels and up to 256 digital I/O pin channels with the ETS-600.
-
Product
Modular Functional Test Platform
LX-OTP2
Test Platform
The OTP² system platform has recently been available in both the PXI and LXI versions. The OTP2 system platform enables the cost-effective and fast implementation of function test systems based on defined modules and function blocks. Thanks to the open system interfaces, customer-specific adjustments can be made at any time without any problems. When considering options for your next generation functional test system, it is important to assess the entire life cycle of the system and the associated costs and efforts. Use OTP² to accelerate development cycles and reduce the development effort for new functional test systems.
-
Product
LED Indicators
-
The "semi-analog" LED indicators display the measured value using 71 LEDs. These indicators are designed to withstand very strong vibrations yet have the familiar look of an analog indicator.
-
Product
3 Digit LED Voltmeter
SP 300
-
The SP 300 is a 3 digit LED voltmeter with 9mm (0.36") digit height. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into an 8-way SIL socket and can be fitted into a panel via the fixing clip. Splashproof protection to IP65 is achieved by fitting the seal supplied.
-
Product
OTP-Based Test System
Test System
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
Product
LED Photoreactors
-
Luzchem's LED exposure tools allow photochemists and photobiologists to work with their choice of broad or narrowband visible dimmable light sources. Choose from a variety of broadband white LEDs or from our selection of narrowband blue, green, yellow and red LEDs.
-
Product
Multi Channel LED Light Source
LE7
-
Image Engineering GmbH & Co. KG
The iQ-LED is the latest development of Image Engineering. It is a multi channel LED light source that provides the possibility to generate the spectral characteristics of nearly every required light source in just one device. With its 22 different software controlled LED channels it is possible to generate a spectral match of standard light sources such as, D50, D55, D65, A, B, C etc. with very high accuracy.
-
Product
LED Driver & Bulb Testing Instruments
-
Providing you the best range of Driver Testing Machine, Digital Power Analyzer, THD Power Analyzer, AC Production Tester, Smart QC Meter and Power Supply Tester with effective & timely delivery.
-
Product
In-Line 2-Module In-Circuit Test System; i337x, Series 5i
E9988E
In-Circuit Test System
Short wire fixturing eliminates problems commonly found with long wire fixturing, such as noise and deterioration of test stability. This translates into transportable, repeatable and stable tests on your i3070 Series 5i, even if you need to deploy tests halfway across the globe, or on different manufacturing sites.
-
Product
LED Light Measurement System
-
RayClouds Photoelectric Technology Co.,Ltd.
The LED optical measurement system includes Blue Light Analyzer, Glare Analyzer, LED Light Intensity Measurement, LED Goniophotometer, Lighting Electrical Measurement System, LED LightBar Measurement System, LED Photochromic Tester.
-
Product
LED Backlight Drivers For Automotive
-
Renesas' automotive LED backlight drivers offer dimming solutions for a wide variety of ambient lighting conditions in automotive applications.
-
Product
In-Circuit Test System
TestStation LX
Test System
TestStation LX is a cost-effective in-circuit test solution providing high-volume electronics manufacturers with reliable, high-quality test for the latest printed circuit board assembly technologies.
-
Product
LED Optical Aging Test Instrument
LEDLM-80PL
-
LEDLM-80PL LED Lumen Maintenance and Aging Life Test System is designed according to standards of IES-LM-80, IES-LM-82, TM-21 and GB2312-80, and the software is developed base on Arrhenius model. LED has the features of long life, but with the different working condition and drive current, its life will be different, but generally the life will be around 50K hours. Differ from the traditional lightsource, LED light will decay gradually rather than extinguish instantly, so in the standard of LM-80, it introduces L70, L50 and etc.
-
Product
LED Illuminator
-
Luzchem's LED-Illuminator, is a compact system for irradiating samples from 3-200 ml in size. Features a unique 7-LED design with lenses that focuses all LEDs on one spot! LEDi-KIT3 includes Luzchem's standard RGB head, comprised of two red, two green, two blue and one white LED. Or, choose from our broad range of high-powered single-coloured LEDi-Heads.
-
Product
LT-300A Aging-Life Test System For LED Luminaires
-
Hangzhou Everfine Photo-E-Info Co., LTD
LT-300A system is widely used for normal /accelerated aging, lumen maintenance measuring, chromaticity shift measuring, lifetime evaluation and temperature characteristic testing for LED luminaires, arrays, and modules. The extrapolation of lifetime by programmable models is also available to estimate the lifetime of LED luminaires.
-
Product
LED Color Sensor
Smart FINN Bright
-
LED applications have evolved from simple status indications to extremely bright lighting for commercial, industrial and military applications. The intensities of these bright LEDs are beyond the capability of the human eye to withstand, let alone be able to discriminate for color. Much like the human eye with sunglasses, we are able to shade our FINN sensors in order to provide accurate color and intensity measurements.
-
Product
LED Flash Drivers
-
Analog Devices LED flash drivers support general LED lighting, building technology, scanning equipment, and a range of other technologies. A range of features, such as automatic phototransistor controls and overtemperature protection, as well as compact size and diverse programmability options, allow these devices to be used in a number of applications including:
-
Product
LED
-
For instruments, switches, icon backlighting, and general and architectural lighting, Vishay offers LEDs in a variety of SMD and leaded packages. Leaded LEDs are available in 1.8 mm, 3 mm, 5 mm, and square 4-lead TELUX packages. Standard and power LEDs are offered in packages with PLCC-2/4 dimensions, while MiniLEDs feature a small 2.3 mm x 1.4 mm x 1.2 mm SMD package. The next smallest package is the 0603 in lead-frame and PCB-based versions, followed by the smallest package in the Vishay portfolio: the new 0402 series. The 1 W Little Star® features a height profile of < 1.5 mm, which is 17 % thinner than a typical PLCC6 package.
-
Product
LED CIRCUIT TESTER, 6-12V AND 24V
MD1646
-
Checks high and low voltages on 6-12V and 24V circuits. Connect the red lead to a power source and the black lead to a ground source. Tester will light up red for power and green for ground during testing.
-
Product
EBIRST 78-pin D-type To 68-pin Female SCSI Adapter
93-006-222
Test Adapter
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
