Short Locators
A short locator is used to identify unintentional connections in electric circuits.
-
Product
Shorts
-
These coaxial shorts are useful to establish a reference plane, as well as providing certain protections from the environment. SMA shorts and Type N Shorts can establish reference planes. These coaxial shorts are not VNA grade but are often used at lower frequencies for calibration purposes. Included here are the following shorts: 2.4mm, 2.92mm, 2.2-5, BNC, N, SMA, SMB, SMP, SSMA, SSMC, TNC. Note, more options: 1.85mm is compatible with 2.4mm, 3.5mm is compatible with 2.92mm.
-
Product
Coaxial Short
85140A
Terminator
The Keysight 85140A coaxial short is used for establishing measurement planes for known reflection phase and magnitude in 50-ohm coaxial systems. It has a 2.4 mm male connector.
-
Product
Tool, Locator, TriPaddle, Receiver
910104127
Locator Tool
Used with crimp tool part # 910 101 103 to crimp TriPaddle receiver contacts to 20-28 AWG wire. This locator contains an integrated wire stop for consistent contact crimping.
-
-
Product
Tool, Locator, Micro Power, Receiver
910104145
Locator Tool
Tool, Locator, Micro Power, Receiver.
-
Product
Short Hot Stick
HS-800
-
Standard Electric Works Co., Ltd
Single foamed hot stick. Universal sunrise fitting on the head to fit special tool fittings. Rated at 100 kV per 300mm (1 minutes). Can be connected to 275 HP HV proximity detector, 21X HVD capacitive HV detector and 272 HP Non-contact HV detector. Meets IEC 60855. Reasonable price.
-
Product
Fault Locator
TRANSFLEKT
-
TRANSFLEKT simplifies the location of transient faults on the low voltage distribution network.
-
-
Product
Visual Fault Locators
-
Visual fault locators are used to identify problems with your fiber. GAOTek visual fault locators typically are applied for fiber tracing, fiber routine, and continuity checking. Imagine being able to easily identify when and where a fiber is breaking, bending, or when there’s a threat to the fiber layer.
-
-
Product
Short Buddy
-
A tool designed for hands free electrical troubleshooting. Short Buddy uses audible beeps to help find intermittant electrical connections and wiring issues.
-
Product
Cable Locator
-
A cable locator can locate open power cables, either live or without current, with voltages up to 300 V. A cable locator can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power to the cable being tested. Many cable locator devices also can locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy.
-
Product
Cable Locator
CL 20
-
Cable fault location with the BAUR CL 20. The CL 20 cable locator comprising a transmitter and a receiver is used to determine the exact location of cables and metal pipes. The ability to determine laying depths of up to 4.5 m and to measure signal currents at the touch of a button allows you to obtain reliable information on the position of the cable within the shortest time.* Fast and exact location of position and laying depth of cables* Intuitive operation – no special measurement knowledge required* Lightweight and manageable
-
Product
Short
FSXE
-
The FSXE Fixed Waveguide Shorts and the TSXE Tunable Shorts are available for creation of the shorts circuit conditions in waveguides. The TSXE Tunable Waveguide Shorts are movable shorts, adjustable through at least half a wavelength at the low end of the band. The TSXE Shorts consist of movable noncontacting choke plungers within a straight section of waveguide. The FSXE and TSXE Shorts are provided in five waveguide bands between 33 GHz and 225 GHz.
-
Product
Fault Locator
WEEZAP
-
WEEZAP is an LV vacuum circuit breaker combined with advanced measurement and protection capability.
-
Product
Locators
EZiSYSTEM xf-Series
-
The EZiSYSTEM xf-Series utility locating and tracing equipment makes locating buried utilities easy and efficient. The xf-Series locators have additional low frequencies enabling you to locate and trace utilities over longer distances and in congested environments. With an EZiCAT locator there is no need to manually adjust the sensitivity. With the unique Automatic Pinpointing feature, users can hold press the trigger and start locating.
-
Product
Ground Fault Locator
DC Trace
-
SCOPE introduces DC Trace, the most advanced and user friendly DC Earth (Ground) Fault Locator. This portable instrument consisting of Signal Generator & Signal Receiver (DC TraceR) uses latest digital signal processing technology. It’s ability to detect earth faults in live DC system quickly & accurately in online condition greatly relieves the substation maintenance engineers from nightmare of earth leakages & it’s detection.
-
Product
Cable Fault Location
-
BAUR cable fault location devices and systems cover the entire cable fault location process: During pre-location, the position of the fault is roughly located. The subsequent pinpointing enables precise determination of the cable fault. You can use various measurement methods depending on the kind of fault and cable type.
-
Product
Pen-based Fault Locator
-
*Find the breakpoint, bending or cracking*Find the fault of OTDR dead zone*Identification of fiber from one end to other end*Universal adaptor*Testing distance up to 8km*Lightweight, red laser output, both SM and MM available
-
Product
Tool, Locator, TriPaddle, Receiver
910104146
Locator Tool
Tool, Locator, TriPaddle, Receiver (only for contact p/n #'s 610110128 Rev C+ and 610110177)
-
Product
Pipeline & Cable Fault Locator
TM2000
-
TM2000 Pipeline & Cable Fault Locator is designed for the Underground utilities route locating, the depth measuring and disatance tracing.
-
Product
Noise Location Package
Type HFDF
-
National RF’s Type HFDF high frequency location system is a proven noise hunting and location directional antenna system that allows you, in many cases, to walk right up to the source of High Frequency (HF) noise! Used by several power companies around the United States, professional noise hunters, and other communications specialists, the HFDF has located noise sources that emanated from pole power transformers, arcing electric fences, CATV in-line amplifiers, plasma TV screens, and even Marijuana grower’s heating lamps! The system incorporates several plug-in, tunable magnetic loop sensors of a proprietary National RF design, that cover the frequency range between 1.8 MHz and 55 MHz. The unit is packaged in a hand-held, lightweight metallic enclosure, with a pistol grip and a magnetic compass mounted on top. The compass is used to get magnetic bearings to the noise source, which may be plotted on a map to triangulate, and ultimately pin-point, the location of the noise source. In certain cases, our customers tell us that they have been able to walk right up to the interfering noise source and correct the situation on the spot!
-
Product
Cable Fault Locators
-
Cable Fault Locator is a device used for short circuit faults, cable cuts, resistive faults, intermittent faults, and sheath faults. Fiberinthebox supply cable fault locator for power cable, optical fiberal cable, etc. Fault Location in Power Cable is designed to locate cable faults, pinpointing the fault location, route tracing, cable identification, voltage withstand test and cable information management. It can locate all kinds of cable faults for all voltage level cables, including open circuit, short circuit, low insulation, high insulation and flashover faults, etc. Most power cables were buried underground, invisible, and out of reach, with modern new power cable fault locater, it can find the fault point quickly, solve problems immediately and restore power supply.
-
Product
Metal Box Locator
-
The Elcometer Metal Detection range includes Valve Box Locators that are rugged and simple to use making them the ideal choice for all location work in all types of terrain.
-
Product
Rebar Locator
Profometer PM-650 AI
-
The Profometer PM-650 extends the measuring modes of the Profometer PM-630 with the unique Cross-Line Mode and further analysis functions. The Cross-Line Mode allows users to measure the rebars of the first and second layer typically arranged in a rectangular mesh.
-
Product
Real-Time Location System
RTLS
-
The new real-time location system „RTLS“ combines high localisation accuracy in an industrial environment with unique technical features which allow a broad use of the system in different applications. It is possible to use RTLS in complex environments for different applications. Tracking and Digitising Production and Logistics Processes manufacturing progress and a transparent material flow.The real-time data about the location and status of the objects available with the RTLS form the basis for networking the parties involved and the logistics processes in their value-added chain.
-
Product
Rebar Locator
Profoscope
-
The Profoscope is a versatile, fully-integrated rebar detector and cover meter with a unique real-time rebar visualization allowing the user to actually “SEE” the location of the rebar beneath the concrete surface to a maximum depth of 180 mm. This is coupled with rebar-proximity indicators and optical and acoustical locating aids. Rebar diameter can also be estimated within the specified testing range. The Profoscope combines these unique features in a compact, light device that allows the user to operate this rebar detector with one hand making the task of locating rebars a simple and efficient process. In addition, Proceq’s rebar detector convinces through its intuitive user interface making rebar detection easy.
-
Product
Overhead Fault Location
-
Schweitzer Engineering Laboratories, Inc.
Overhead faulted circuit indicators include easy-to-spot displays to help direct line crews to the faulted line sections—enabling faster restoration of power and improved customer uptime.
-
Product
Short Circuit Loop Impedance Meter
AMZC-306
-
Voltage measurement up to 750V and up to 250V with resolution 0,1V ; Measurements using Uni-Schuko adapter or test wires 1,2; 5; 10 and 20m ; Loop impedance measurement with resolution 0,01Ω and much more
-
Product
Traction Battery Short Circuit Test Machine
-
Guangdong Bell Experiment Equipment Co.,Ltd
Traction Battery Short Circuit Test Machine Relevant standards requirement:Single Storage Cell Safety Test6.2.4 Short circuitCharge the single storage cellaccording to 6.1.3 standardThe cellis to be short-circuited by connecting the positive and negative terminal with a external resistance of less than 5mΩ for 10 minObserve for 1HBattery module safety test6.3.4 Short circuitCharge the battery module according to standard 6.1.4The battery module is to be short-circuited by connecting the positive and negative terminal with a external resistance of less than 5mΩfor 10 minObserve for 1H
