Short Locators
A short locator is used to identify unintentional connections in electric circuits.
-
Product
DC Earth Fault Locator
GFL-T + GFL-R
-
The DC Earth Fault locator is suitable to test the DC Battery System and Trace Ground Faults. The system is suitable for Power Plants, Sub-Stations upto 765KV and other industries. The system is highly capable in tracing and pin pointing the DC earth faults in a live system without requiring any shut downs. The receiver sensitivity of 1mA and better is capable to trace most complex fault.
-
Product
Ground Detection and Earth Fault Location Equipment for Ungrounded or Floating DC Systems
ZX3
-
The ZX3 is a ground fault locator that finds grounds (current leakage) on a battery system positive rail, the negative rail, on both rails simultaneously, in a field device, battery bank or solar array/string, regardless if they are high resistance or low resistance or in a capacitive environment. It also can provide more information about the DC ground than any other equipment available, providing maximum analyzing capabilities.
-
Product
Short Termination, 4-Terminal Pair
42091A
Terminator
Use for performance tests of the 4-terminal pair LCR meters and impedance analyzers.
-
Product
Detection of Earth Faults (PtG) and Short Circuit (PtP) Faults
CableTroll 2330
-
CableTroll 2330 is an indicator for detection of earth faults (PtG) and short circuit (PtP) faults on multi and single core cable terminations. The unit uses NorTroll type current sensors.
-
Product
Microprocessorized Instrument of Short Circuits
MKZ-100
-
The mobile meter instrument designed to control of short between electrical sheets to stack up.
-
Product
Underground Cable Fault Locator
KM-CFPL-620 /620B
-
Kusam Electrical Industries Limited
“KUSAM-MECO” underground Cable Fault Pre-locator is an automatic Cable Fault Locator which adopts ARM, FPGA & Dot Matrix Color LCD display Technology. This tester combines both pulse reflecting technology (TDR) & (intelligent Bridge testing (Bridge) (Model-KM-CFPL-620B) for measuring the exact fault location such as broken line, cross faults, earthing, (poor insulation & poor contact of the lead covered cables as well as plastic cables. (Model-KM-CFPL-620B)).It is a microprocessor based fault locator with a user friendly menu. It is easy to operate. It tests almost all telecom & signal cables. It has an English menu which is easy to understand & use. With Megameter & Ohmmeter it enables to test insulation resistance & loop resistance. It has USB Port for uploading test data to computer
-
Product
Cable Locators
-
We have cable length meters, locators and fuse finders for electrical, data network and telecommunication applications.
-
Product
Short Focal Length Triple Grating Imaging Spectrographs
Triax Series
-
The TRIAX series use special corrective optics that maintain an excellent image quality and resolution along the length of the slit as well as along the dispersion axis in the exit focal plane. Thus, a point source on the entrance slit is re-imaged as a point for every occurrence of its wavelength in the focal plane.
-
Product
Cable Fault Locating Equipment
-
Commonly used to test underground coaxial and twisted pair cabling, along with transmission lines and other industrial electrical cables.
-
Product
Platinum Tools Fiber Optic Visual Fault Locator
#TVFL100
-
Fiber optic visual fault locator works with virtually all 1.25mm and 25mm fiber optic sizes and connector types.
-
Product
Hazardous Location Sensors
S88
-
The S88 pH Sensors are one part of the Model S88 Intelligent Sensors product line. The S88 Sensors offering includes pH Sensors, ORP Sensors, Ion Selective Sensors, Dissolved Oxygen Sensors, Conductivity Sensors and Resistivity Sensors. The S88 sensors have two Universal Sensor Designs; Insertion/Submersion or Valve Retractable with flared end to prevent blow out. The standard S88 sensors have 316 Stainless Steel housings although various materials of construction are available to maximize sensor performance while minimizing cost of ownership. For other materials of construction request a quotation from the factory.
-
Product
Fiber Optic Power Meters and Fault Locators
-
Fiber optic communication systems require the right tools to commission new links and to troubleshoot existing links. Fluke Networks has a wide range of Fiber Optic testing products to help certify that power losses are within standards and to troubleshoot broken and high loss links on single mode and multimode fiber. Fluke Network fiber optic tools are designed to be rugged and reliable, and to get the job done.
-
Product
Pen-type Visual Fault Locator (VFL)
JW3105A
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3105A VFL is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network. It includes:
-
Product
Shorted Turns Tester for Bobbin Wound Coils
Model STT-4
-
International Electro-Magnetics, Inc.
The STT-4 Shorted Turns Tester offers a quick and easy means to detect shorted turns in bobbin coils. It is a non-stress and non-contact test.
-
Product
Visible Fault Locator
FiberLink 6656
-
Fiberlink 6656 Visible Fault Locator is a light-weight, hand-held tool used to quickly troubleshoot faults in the continuity of both single-mode and multimode fibers, especially at fiber launch points or in OTDR dead zones.
-
Product
Vehicle Mount Cable Fault Location System
-
Weshine Electric Manufacturing Co., Ltd
VS2088Plus Built in Booster And Capacitor In Vehicle Underground Cable Fault Test Device
-
Product
Under Ground Cable Fault Locator
-
Widely used in electrical and power generation sector for testing underground cables in order to detect any fault.
-
Product
Cable Sheath Fault Location
-
Locating cable sheath faults is one of the last steps in cable testing, occurring after you have identified the existence of a cable fault via the identification procedure based on your specific site variables and the type of system you are working on
-
Product
Travelling Wave Fault Location Test Kit
PH Series
-
PH series travelling waveform fault locating relay/equipment test set is a new device to meet the needs of testing and verification for travelling wave fault location equipment and protection relay with TWFL function.
-
Product
Ground-Fault Location Products for Ungrounded Systems
-
When combined with Bender's ground-fault detectors and current transformers, EDS series modules provide fast, automatic ground-fault location in ungrounded systems. Fault location takes place while the system remains online without the need to open branch circuit breakers or disconnect equipment. Bender's fault location system works on both AC and DC systems, as well as systems with variable frequency drives. A standalone, portable fault location system is also available.
-
Product
Cable Fault Locator
TX2003
-
6 km (19,000ft) 0.5mtr dead Zone Selectable Cable Impedance Warble Tone Generator Rapid Fault Location Large 128x64 LCD with Backlight Scratch Resistant Display Environmental Protection IP54 CE Approved 3yrs Manufacturers Warranty 60 Hours Battery Life
-
Product
Rebar Locator
Profometer PM-600
-
Profometer PM-600 is an advanced cover meter for the precise and non destructive measurement of concrete cover and rebar diameters and the detection of rebar locations using the eddy current principle with pulse induction as the measuring method.
-
Product
Mobile Cable Fault Location System
Syscompact 2000
-
Fault location with Syscompact 2000. The Syscompact 2000 is a multifunctional cable fault location system designed for modular 19" rack technology. The integrated surge and test generator is used for cable and sheath testing as well as for precise location of high-resistive and intermittent faults. The SYSCOMPACT 2000 is preferably used in low- and medium-voltage networks for fault location up to a cable lengths of 65 km. * Fast and reliable * Precise, dependable cable fault location High performance * high voltage unit* Integrated proven cable fault pre-location methods
-
Product
Cable Fault Locator
FaultCaster
-
Low Cost Full specification Professional Digital TDR Measures Distances to Open or Short Circuit Faults Extended Measuring Range to 2000m (6000ft) on all cable types Fast-Edge Step TDR technology for improved range & Resolution
-
Product
Prototype /Short Run Production
-
We make high precision Prototype /Short Run Metal Stampings & Machined Components.We have been successfully serving industrial clients, mostly OEM Automotive Suppliers, since 2005. We have the ability to take your CAD model and turn it into Production Representative Parts within days.
-
Product
ATX Coaxial Probe V2.0 Short
-
The ATX Coaxial Probe V2.0 stands as a revolutionary solution in capacitive measurements for ICT test systems. Engineered for optimal performance, this universal probe guarantees heightened stability and reliability, essential for enhancing the robustness of your production processes. Its innovative mechanical design prevents twisting, while the individually adjustable height suspension allows for customized measurements suited to various components.
-
Product
Service Drop Locator
VM-560
-
The VM-560 is a general-purpose locator used to detect buried pipe and cable services in a variety of situations. With a 50/60Hz passive power locating frequency and three active frequencies, the VM-560 locator will meet the requirements of those wishing to detect the presence of active power cables and to trace short ranges. The VM-560 transmitter also has the additional frequency of 8kHz Fault-find so it can be used to detect the presence of ground to sheath faults on cable when used with the VM-510 Stand Alone A-Frame fault locator.
-
Product
Thumpers and Cable Fault Location
-
Cable testing can be broken down to different steps of the process, starting with a time domain reflectometer test to look for an incident signal on the line or, in some high resistance situations, VLF testing. These tests will identify a fault, allowing you to move on to pre-locating it. In some low resistance faults this will occur alongside the identification via the TDR.
-
Product
Cable Sheath Testing and Fault Location System
Shirla
-
Cable fault location with the BAUR shirla. Shirla the fault location system is used for cable and cable sheath testing as well as for pre-location and pinpointing of cable faults. The pre-location based on the measuring bridge principle according to Murray and Glaser that is designed especially for power cables, also enables pre-location for control and lighting cables. Null balance and evaluation take place automatically.* Cable and cable sheath testing up to 10 kVC* Resistance measurement* Cable and cable sheath fault pre-location with precision measuring bridge* Adjustable cable sections that can be defined with length, conductor cross-section and material respectively and can be considered in the distance calculation
-
Product
Intelligent Cable Fault Locator
TM800
-
TM800 Cable Fault Locator is a portable field instrument working on TDR and bridge methods, adopting advanced micro-electronics technology. It is designed to locate accurate fault points in such cables as telecommunication leadsheathed cable, plastic cable or user’s lead covered wire, while the faults include break, mix, earthing, defective insulation, or poor connecting. It is and ideal function-stable instrument for the field operator to improve work efficiency, in addition, it can also be used for circuitry project checking electric property testing of the cable.
