Synchro / Resolver Converters
converts Synchro and Resolver analog shaft angle signal to a digital signal.
See Also: Synchro/Resolvers
-
Product
DC-Angle to Synchro or Resolver Converters
LDS & LDR
-
Computer Conversions Corporation
The LDS 500M Series are high accuracy, drift free, and continuously updating DC-Angle to Synchro or Resolver Converters designed for Military and Industrial simulation and control applications.
-
Product
HDG and OBS Track Select Panel
TA-260
-
Universal Heading and Track Selector Panel This panel provides a synchro transmitter for Heading and a synchro resolver for Nav converter alignment. The synchros are mounted on industry standard 18:1 dual speed drives for maximum accuracy and repeatability. This unit can be used to calibrate both manual and automatic converters. This panel provides a rear mounted interface connector as well as front mounted tip jacks for independent breakout if so desired. The TA-260 also provides two discrete switches associated with the resolver configuration. The 30Hz/400Hz switch is provided to allow the resolver to be properly compensated for the type of Nav converter to be aligned. The second switch allows you to open or short the resolver rotor lead as may be required by some newer GPS equipment. This panel is lightweight enough for portable use or may be rack mounted.
-
Product
DC to Synchro and DC to Resolver Converters
-
Computer Conversions Corporation
The LDS 500M Series are high accuracy, drift free, and continuously updating DC-Angle to Synchro or Resolver Converters designed for Military and Industrial simulation and control applications.
-
Product
Synchro to Digital-Resolver to Digital Converters
SDC-F-RDC-F
Digital / Synchro Converter
Computer Conversions Corporation
SDC/RDC-F Series are Industry Standard Tracking Synchro and Resolver to Digital Converter modules with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command.
-
Product
Digital to Synchro Converter
DSPH
Digital / Synchro Converter
Computer Conversions Corporation
The DSPH Series High Power Digital to Synchro Converters, are proven, high efficiency, low cost, compact, reliable solid state synchro drivers; designed for demanding Naval/Maritime, Aircraft, fire control and Radar/Antenna related, applications. They are commonly used on synchro based data transmission, retransmission, simulation, and instantaneous absolute position indicating and active control systems.
-
Product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
Digital / Synchro Converter
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
Product
synchro or resolver to digital (BCD) converters
AIT
Digital / Synchro Converter
Computer Conversions Corporation
The TSb series are miniature, high performance continuous tracking synchro or resolver to digital (BCD) converters and angle indicators employing a type 2 servo loop, designed for military and industrial control applications. They will accept any 3 wire synchro or 4 wire resolver input over a frequency range of 50 to 1200Hz. and convert it into 0 to 359.9 degrees or +/-179.9 degrees, TTL compatible BCD data.
-
Product
Synchro to Digital-Resolver to Digital Converters
Synchro- Burst
Digital / Synchro Converter
Computer Conversions Corporation
Computer Conversions Corporation's Synchro-Burst is a complete 2 channel Synchro to encoder interface designed to easily integrate inherently absolute rotary synchro, resolver or linear LVDT position sensors into motion controls and counters that are normally only designed to facilitate incremental encoder feedback.
-
Product
Synchro to Digital and Resolver to Digital Converters
Digital / Synchro Converter
Computer Conversions Corporation
Resolution: Up to 20 Bit Single-speed Resolution, Up to 24 Bits Multi-Speed Multi-Turn Resolution.Accuracy: +/- 7 to +/-19 arc seconds 20 bit, +/-40 arc seconds 16 bit, +/- 1',+/-2.3 and +/-4' Reference Inputs: 2- 11.8V 26/ 115Vrms L-L 47 to 10,000 Hz. Isolated to > 500VDCSignal Inputs: 2 - 11.8, 26, 40, 90V.L-L. Isolated to . 500VDC.Options: Multispeed synchro input and bus card interface.
-
Product
Digital Synchro and Digital to Resolver
DSL- DRL
Digital / Synchro Converter
Computer Conversions Corporation
The DSL - DRL Series are highly reliable, miniature, low profile and low cost, continuously updating Digital Synchro and Digital to Resolver (AC Sine / Cosine) Converters designed for military and industrial control applications.
-
Product
725-Watt (270VDC input) DC/DC Converter, SOSA™ Aligned, 3U VPX
VPX57HS
DC Converter
NAI’s VPX57HS-31 is NAI's latest +270 VDC Input, VPX DC/DC Converter. The VPX57HS was developed in alignment of the SOSA™ Technical Standard and is capable of handling up to 725 Watts of output power. It plugs directly into a standard 3U VPX chassis with a VITA 62 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
Synchro to Digital-Resolver to Digital Converters
HRDCK-HSDCK
Digital / Synchro Converter
Computer Conversions Corporation
HSDCK and HRDCK series are the highest accuracy, miniature tracking synchro and resolver to digital converters in the marketplace. They are designed specifically for ultra precise requirements in the most demanding industrial and military applications.
-
Product
Synchro to Digital-Resolver to Digital Converters
MRDC
Digital / Synchro Converter
Computer Conversions Corporation
Computer Conversions’ MRDC64-3 is a miniature single chip solution for providing a complete 1 x 64 speed resolver interface into any demanding industrial or military application.
-
Product
AC-DC Rectifier / Converters
DC Converter
These following AC-DC converters all can provide 3.3/5/9/12/25/24/28/48V etc output. Newly acquired 2U rack mount 48V rectifier is a mature solution for 48V telecom systems.
-
Product
25-Watt DC/DC Converter
55GS1
DC Converter
NAI’s 55GS1 is a COTS, 25-Watt DC/DC Converter that accepts a +28 VDC input and provides a single full-power output at a baseplate temperature of +100°C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
Product
600-Watt DC/DC Converter, 6U VME/cPCI
55U91-01
DC Converter
NAI’s 55U91-01 is a 600 Watt DC/DC Converter that plugs directly into two card slots in a standard 6U VME chassis. It is conduction-cooled through the card edge/wedgelock. This switching power supply accepts +28 VDC input, provides up to 9 outputs at up to 614 Watts, and addresses the power supply needs of both VME and cPCI systems.
-
Product
50-Watt DC/DC Converter; Dual Output
55JD1
DC Converter
NAI’s 55JD1 is a 50-Watt DC/DC Converter that accepts a +28 VDC input. This COTS unit provides full-power output, dual at a baseplate temperature of +100° C.
-
Product
500-Watt (270VDC Input) DC/DC Converter, 3U VPX
VPX57-31
DC Converter
NAI’s VPX57-31 is the industry's first 500-Watt DC/DC Converter that accepts a +270 VDC Input and plugs directly into a standard 3U VPX chassis with a VITA 62 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
100-Watt DC/DC Converter, 3U cPCI
55LQ2
DC Converter
NAI’s 55LQ2 is a 100 Watt DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This modular, switching power supply accepts +28 VDC input and provides a single output at up to 100 Watts.
-
Product
400-Watt DC/DC Converter
VPX55-3
DC Converter
NAI's VPX55-3 is 400-Watt DC/DC Converter that plugs directly into a standard 3U VPX chassis with a VITA 62 0.8" power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
Digital to Synchro and Digital to Resolver Converters
Digital / Synchro Converter
Computer Conversions Corporation
1.2VA, 1.5VA, 4.5VA and 5VA Models60 or 400, & 60 and 400 Hz. Models to 22 KHz.Trouble Free Isolated Reference Inputs & Signal OutputsUltra High Efficiency, Low DistortionSelf Powered off the AC Reference Input (DSP Series)Internal Cool AC-Pulsating Supplies (DSP Series)Very Low Loss & Heat DissipationFULLY INTEGRATED, NO EXTERNAL COMPONENTS REQUIREDVery High Resistance to Shock and VibrationHigh Reliability Throughout ImplementationIsolated, Transient, Therrnally & Short Circuit Protected Outputs
-
Product
100-Watt DC/DC Converter
55LS1
DC Converter
NAI’s 55LS1 is a COTS, 100 Watt DC/DC Converter that accepts a +28 VDC input and provides a single full-power output at a baseplate temperature of +100° C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
Product
75/150-Watt DC/DC Converter w/Holdup, 3U cPCI
75PS4
DC Converter
NAI’s 75PS4 is a DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This programmable, switching power supply accepts a +28 VDC input and is available in either a 75 Watt or 150 Watt-version.
-
Product
1000 Watt AC/DC Power Converter, 6U VPX
VPX56H-6
DC Converter
The VPX56H-6 is NAI's latest high power, 1000 Watt AC/DC converter which accepts either a 3Ø 115VAC L-N inputs or a +270 VDC input. It plugs directly into a standard 6U VPX chassis with a (VITA 62) 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
Digital to Synchro Converters
DSP
Digital / Synchro Converter
Computer Conversions Corporation
The DSP Series are high efficiency, AC Reference powered, Transformer Isolated, continuously updating “whole” Digital to Synchro Converters, designed for high performance Military and Industrial applications.
-
Product
Synchro to Digital-Resolver to Digital Converters
SACP-RACP
Digital / Synchro Converter
Computer Conversions Corporation
Computer Conversions Synchro-Resolver to ACP/ARP Converters accept choice of synchro-resolver input options, power input, and mounting configuration, converts synchro/resolver input into ACP (Azimuth Change Pulse) and ARP(Azimuth Reference Pulse) type outputs suitable for 75 ohm drive.
-
Product
Keysight 4-Channel D/A Converter with Waveform Memory for 34980A
34951A
Digital / Analog Converter
The Keysight 34951A module for the 34980A Multifunction Switch/Measure Unit has four electronically calibrated analog channels that can output up to +/-16V DC or +/-20mA DC with 16 bits of resolution. Each channel can be updated individually with a 200 kHz update rate. You can use the standard waveforms provided or create your own with over 500,000 points. These points can be dynamically allocated among one or more channels and output as a point-to-point arb.
-
Product
725-Watt (28VDC input) DC/DC Converter, SOSA™ Aligned, 3U VPX
VPX55HS
DC Converter
NAI’s VPX55HS-31 is NAI's latest +28 VDC Input, VPX DC/DC Converter. The VPX55HS was developed in alignment of the SOSA™ Technical Standard and is capable of handling up to 725 Watts of output power. It plugs directly into a standard 3U VPX chassis with a VITA 62 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
Synchro to Digital-Resolver to Digital Converters
SDC40-RDC40
Digital / Synchro Converter
Computer Conversions Corporation
The SDC series are low cost, miniature, continuous tracking, synchro or resolver to digital converters designed for military and industrial control applications. They will accept any 3 wire synchro or 4 wire resolver input and convert it into 14, 12 or 10 bit natural binary angle data.
-
Product
Isolated USB To RS-232/422/485 Converter
ADAM-4561
Digital / Analog Converter
Power from the USB portHot swap function supportedIsolation protection 3000 VDC providedAutomatic RS-485 data flow controlTransmission speed up to 115.2 kbps
