Synchro/Resolvers
Compute trigonometric values over 360 degrees of rotation by varying the magnetic couplings between its primary (rotor) and secondary (stators) windings.
See Also: Synchro / Resolver Converters, Angle Position Indicators, Stator, Rotor, Synchros, Resolvers, Synchro / Resolver Simulators
-
Product
Synchro to Digital-Resolver to Digital Converters
SDC-F-RDC-F
Digital / Synchro Converter
Computer Conversions Corporation
SDC/RDC-F Series are Industry Standard Tracking Synchro and Resolver to Digital Converter modules with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command.
-
Product
Synchro and Resolver Angle Indicator
AIT5
-
Computer Conversions Corporation
This series of units were designed to satisfy Hi speed synchro/resolver applications where the output data must be fresh and no data staleness can be tolerated. The tranducers utilized are the same as in the regular MDS series, however different tracking electronics are used. The resultant data tracks the input shaft perfectly and is always fresh and accurate at input speeds up to 64 revolutions per second, depending on the resolution. Data in BCD or Binary formats are available, and clean, unambiguous crossovers are guaranteed.
-
Product
Angle Position Indicators
Angle Position Indicator
NAI offers a wide variety of Angle Position Indicators (APIs) that perform high quality analog-to-digital conversions of Synchro or Resolver data. These measurement instruments deliver industry-leading performance in a variety of accuracy and resolution grades, with various packaging options available. Multiple communication control interfaces include:*Touch screen*Front panel*Optical mouse*IEEE-488*Ethernet*USB
-
Product
LVDT I/O Cards
CPE4000
-
Computer Conversions Corporation
Computer Conversions’ CPe4000 Series are CompactPCI-Express (cPCIe) and PXI Express (PXIe) compliant: Synchro, Resolver, and LVDT/RVDT I/O Cards (predominantly output cards), with GEN1 and GEN 2 PCI Express interface, designed for accurate and reliable commercial, industrial and COTS-Mil. applications in test, simulation, motion control and shipboard data distribution. The CPe4000 Series drive up to 4 channels of Synchro, Resolver, 3-wire LVDT/RVDT outputs, or up to 8 channels of 2 wire LVDT/RVDT AC Sensor output sets.
-
Product
6U CPCI Multifunction I/O Board
78C1
Multifunction I/O
The 78C1 is a universal 6U cPCI Multifunction I/O Board that eliminates the complexity and size constraints of using multiple, independent, single-function cards. This single slot card has six module positions, allowing developers to achieve a custom configuration with any combination of function modules, such as A/D (10-channels), D/A (10-channels), Discrete I/O (16-channels), TTL I/O (16-channels), Differential Multi-Mode Transceivers (11-channels), RTD (6-channels), Synchro/Resolver (4-channels), LVDT/RVDT (4-channels), and Signal Generator (4-channels).
-
Product
Synchro/Resolver Boosters
-
NAI offers a variety of multi-channel Synchro/Resolver Boosters that accept Synchro/Resolver inputs, and they deliver isolated outputs capable of driving passive and active loads such as Control Transformers or Torque Receivers. These amplifiers can be used stand-alone or in conjunction with Digital-to-Synchro/Resolver Converters.
-
Product
AC Reference Generators
SR22
-
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 volt excitation to synchros or resolvers in military and industrial control applications. They accept +/-15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6”x3.1”x1”H
-
Product
DC to Synchro and DC to Resolver Converters
-
Computer Conversions Corporation
The LDS 500M Series are high accuracy, drift free, and continuously updating DC-Angle to Synchro or Resolver Converters designed for Military and Industrial simulation and control applications.
-
Product
Synchro & Resolver Buffer Amplifiers
RPMA - SPMA
Amplifier
Computer Conversions Corporation
The SPMA/RPMA Series are low cost solid state synchro and resolver buffer amplifiers, isolators and format converters packaged in industry standard 2.6 x 3.1" modules for printed circuit card mount.
-
Product
Motion Control Solutions
-
DDC offers a complete line of Synchro/Resolver instrument-grade cards and test equipment including angle position indication and simulation, plus a variety of hardware and software to meet today’s civil, military, and COTS/MOTS requirements. DDC is a leading supplier of Synchro/Resolver-to-Digital and Digital-to-Synchro/Resolver components—the smallest, most accurate synchro/resolver-to-digital and digital-to-synchro/resolver converters available today. Most of these single chip and hybrid converters are based on ASIC designs, yielding the most reliable and affordable converters ever offered, and are the building blocks for DDC’s card-level products.
-
Product
P104 Synchro/Resolver Simulation Board
73DS2
Simulator
NAI’s 73DS2 is a PC104-compatible Synchro/Resolver Simulation Board with three isolated channels. These channels can incorporate up to three Digital-to-Synchro/Resolver Converters with 1.2 VA drive capability in a stack-through module. With galvanic isolation, one of the outputs can be grounded without affecting performance.
-
Product
AC Reference Generators
SR25
-
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 volt excitation to synchros or resolvers in military and industrial control applications. They accept +/-15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6”x3.1”x1”H.
-
Product
Synchro to Digital-Resolver to Digital Converters
SDC40-RDC40
Digital / Synchro Converter
Computer Conversions Corporation
The SDC series are low cost, miniature, continuous tracking, synchro or resolver to digital converters designed for military and industrial control applications. They will accept any 3 wire synchro or 4 wire resolver input and convert it into 14, 12 or 10 bit natural binary angle data.
-
Product
LVDT I/O Cards
CP3000
-
Computer Conversions Corporation
Universal AC Sensor interface digitizes up to 8 channels of individually Programmable Synchro, Resolver and LVDT/RVDT sensor inputs on a 3U cPCI (Compact PCI) and PXI Compatible plug-in circuit cardProduct allows users to interface into the widest variety of AC Position sensors all programmable within a single cardA must have for anyone using LVDT-RVDT's, Synchros and Resolver sensors or signals, electronic gauging, motion control, and instrumentation.
-
Product
ARINC HSI / ADI Test Fixture
TA-2000
-
The TA-2000 test fixture is a combination panel that incorporates all the standard capabilities of the legacy CTS-11(ADI) and CTS-12(HSI) panels and much more. This panel is married to our model TA-1001 dual synchro transmitter/API panel thus allowing for local stimulus and alignment of the instruments synchros and resolvers. The panel provides for testing of both superflag(28v) and low level meters through a matrix of switching that will allow testing of all meters simultaneously or just individually. The low level meter drive circuit also incorporates an automatic mode that will continuously oscillate the L/R and Up/Dn pointers.
-
Product
2-28 Vrms Input, 2-115 Vrms Exc, 47 Hz - 1 kHz Freq
SDx
-
Synchros and Resolvers are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Resolver-to-Digital or a Synchro-to-Digital converter is used to convert these signals to a digital output corresponding to the shaft angle and/or velocity.
-
Product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
Digital / Synchro Converter
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
Product
High Accuracy AC Reference Source
515
-
Clarke-Hess Communications Research
The Model 515 High Accuracy AC Reference Generator fills a need for a relatively low cost and practical solution for supplying a reference excitation to typical LVDT and Synchro/Resolver transducers. The Model 515 has built-in load sensing which, in effect, yields "zero" output impedance and virtually eliminates the effects of fluctuating output loads. With up to 15 VA of output into loads with as much as 80 of phase shift, the Model 515 is ideally suited to driving inductive loads.
-
Product
Synchro to Digital-Resolver to Digital Converters
HSDC-HRDC
Digital / Synchro Converter
Computer Conversions Corporation
HSDC & HRDC Series are Miniature, Tracking Synchro and Resolver to Digital Converters with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command for military and industrial applications.
-
Product
AC Reference Generators
SR23
-
Computer Conversions Corporation
The SR23 Series are miniature, low cost AC reference generators designed to supply 26 or 115 volt excitation (2-115VAC) to synchros or resolvers in military and industrial control applications. They accept +/-15V DC or +/-12V DC power inputs and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6”x3.1”x1”H.
-
Product
Synchro to BCD and Resolver to BCD Converters
TSBC TRBC
-
Computer Conversions Corporation
The TSB Series are miniature, high performance, continuous tracking, synchro or resolver to digital (BCD) converters and angle indicators employing a type 2 servo loop, designed for military and industrial control applications. They will accept any 3 wire synchro or 4 wire resolver input over a frequency range of 50 to 1200Hz. and convert it into 0 to 359.9 degrees or +/-179.9 degrees, TTL compatible BCD data.
-
Product
SR Series AC Reference Supplies
-
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 Volt excitation to Synchros or resolvers in military and industrial control applications. They accept +/- 15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6" x 3.1" x 1"H.
-
Product
AC Reference Generators
SR21
-
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 volt excitation to synchros or resolvers in military and industrial control applications. They accept +/-15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6”x3.1”x1”H.
-
Product
Synchro to Digital-Resolver to Digital Converters
SDT RDT
Digital / Synchro Converter
Computer Conversions Corporation
The SDT/RDT Series, are single module, tracking, Multi-speed synchro/resolver to digital converters designed for Military and Industrial Applications. They will accept Electrical Multi-speed, or Geared (dual speed) Multi-turn; Synchro or Resolver input sets (Fine/ Coarse), having the most standard ratio’s, and convert them into a single non-ambiguous 16 Bit data word with up to +/-20 arc. seconds accuracy.
-
Product
Phase Angle Voltmeters
Phase Angle Voltmeter
Since the development of the first Phase Angle Voltmeter (PAV) over 50 years ago, North Atlantic Industries has been the industry leader in AC Measurement Instrumentation. Our name has become synonymous with innovation and quality. Our products, specifically designed for defense, industrial, and commercial applications, deliver industry-leading accuracy, repeatability, and reliability.NAI’s units of today are actually multifunction Digital Analyzing Voltmeters that combine a complete Voltmeter, a Phase Angle Voltmeter, and a Waveform Signal Analyzer in a single microprocessor-based instrument. With these versatile and flexible instruments, a wide range of tests can be performed, either manually using the front panel controls or automatically using the IEEE-488 bus. Designed for the Synchro/Resolver and LVDT/RVDT marketplace, NAI’s Voltmeters are used in a variety of applications.
-
Product
VME-Bus Synchro - Resolver LVDT I/O Cards
VB Series
-
Computer Conversions Corporation
The "VB Series" product lines contains VME compatible synchro/resolver converters and absolute encoder systems. These particular cards are ideal for any rotary motion and related process, control, or simulator type application with any VME compatible system.
-
Product
VXI Synchro/Resolver Simulation & Measurement
65CS4
Simulator
NAI’s 65CS4 is a Synchro/Resolver Simulation & Measurement Instrument on a single-slot VXI board. The board incorporates up to four Synchro/Resolver measurement channels and up to four instrument-grade Synchro/Resolver simulation channels, or up to eight embedded grade Synchro/Resolver simulation channels that can be used independently and/or simultaneously.
-
Product
Programmable S/R Standard & Simulator
5300
Simulator
NAI’s 5300 Synchro/Resolver Standard & Simulator is a laboratory-grade, programmable instrument. This model can be used as a true Synchro/Resolver standard for calibrating and testing Automatic Test Equipment (ATE) for Calibration/Metrology Labs, and for Engineering Design and Production Test environments. It can also be used to measure Angle Position Indicators (API) and Synchro-to-Digital converters for static or dynamic characteristics. This model also may use an external reference waveform.
-
Product
Small Synchro / Resolver Digital Panel Meter
DPM-401
-
The industry's smallest synchro/resolver digital panel meters the four digit DPM-401. Only 1.9" x 3.8" x 3.1" deep Bright 0.56" 4 digit LED display
-
Product
Synchro And Resolver Angle Position Indicator
AP-501
-
The AP-501 is a high accuracy, auto-ranging, broad band synchro and resolver angle position indicator. The synchro or resolver angle is displayed on a bright 0.56 inch LED display. The indicator maintains a accuracy up 0.03 degrees even with synchro or resolver phase shifts up to 45 degrees over a frequency range of 47-300 Hz. The 800B301 is a low profile rack mounted synchro/resolver angle position indicator with 360 degree offset capability via front panel thumb wheel switches.
