Bare Board
is a printed wire board only.
See Also: Bare Board Probes, Bare Board Testers, Bare board Fixtures
-
Product
3U OpenVPX Ethernet Switch and Multifunction I/O Board
68G5E
Multifunction I/O
The 68G5E is a 3U OpenVPX board that is configured with an Ethernet Switch module (choose the ES1, 12-Port GbE Cu legacy unmanaged Ethernet Switch, or the ES2 16-Port Cu GbE managed Ethernet Switch with optional 4x 10GBASE-SR 850 nm multimode Fiber Optic interface) and provides additional support for one NAI smart I/O and Communications function module. Uniquely designed, the 68G5E provides ‘independent’ Ethernet Switch capabilities and can operate as a MFIO board end point with access via the 1 x1 PCIe and/or 1x 10/100 Ethernet motherboard Control Port which hosts the NAI Ethernet Protocol Server/Listener application for direct GbE MFIO control. Ideally suited for rugged Mil-Aero applications, the 68G5E delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
16-bit, 200KHz, 16 Isolated Differential Analog Input Board, 8 Isolated 24V Digital I/O
APCI-3002
-
Analog input board, 16-bit resolution, 16 differential inputs with 200 kHz sampling rate.
-
Product
Digital Output Board, 32 Isolated Channels, 5V
APCIE-2032-5V
-
32 digital outputs, 24V or 5V, 500 mA/channel Optical isolation 1000 V Overvoltage protection Short-circuit protection WatchdogAt power-on the outputs are reset to ì0î
-
Product
PCI Data Acquisition Boards
AD8S-100DMA Series - Single low-spur 8-bit, 100 Ms/s
-
Model AD8S-100DMA is similar to the AD8-100DMA, has a single low-noise eight-bit 100MSPS A/D converter and can acquire up to 100 MS/s on a single channel into the host system's RAM. Drivers for 64 bit Linux and Solaris operating systems included.
-
Product
General Purpose 4 Channel Optocoupler Board
-
A general purpose 4 channel optocoupler board using H11G2 optocouplers (see above schematic). Resistors, capacitors, and connections to terminal strip are made by customer to allow for complete flexibility.
-
Product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for six M.2 or NGSFF (NF1) PCIe SSD Modules
SKU-086-36
-
This Squid PCIe Carrier board can support up to six M.2 or NGSFF (NF1) PCIe SSD (solid state drive) modules, with M-key. Supported module dimensions are 2280 or 22110 in length, and a width of up to 32 mm. SSD modules of any capacity may be used, from any vendor, and in any combination.
-
Product
Single Board Computer
VPX3-133
-
Curtiss-Wright Defense Solutions
The VPX3-133 3U VPX Power Architecture Single Board Computer (SBC) is designed with the NXP QorIQ T2080 processor. The T2080 with its 4 dual threaded 64-bit Power Architecture cores, each equipped with an Altivec vector processing engine, provides an impressive amount of processing performance in a very low power foot print.
-
Product
HIL Breakout Board
-
Onboard 192 pin snap-in terminal dramatically simplifies the wiring between your control hardware and your HIL system. As soon as the system is up and running there are 192 test terminals for easy access to all the interface signals: firing pulses, control feedback signals and other analog/digital I/O signals.
-
Product
VPX3424, OpenVPX 3U Single Board Computer
VPX3424
-
The Medusa VPX3424 is a 3U OpenVPX™ (VITA 65) Single Board Computer (SBC) features the all-new Freescale T4240 QorIQ® processor.
-
Product
P104 Synchro/Resolver Measurement Board
73SD4
-
NAI’s 73SD4 is a DSP-based, PC104-compliant Synchro/Resolver Measurement Board with six separate, isolated channels. These channels can incorporate up to six Synchro/Resolver-to-Digital Tracking Converters in a stack-through module. Each channel also produces differential incremental encoder (A & B) outputs (with programmable resolution) and a zero-degree marker pulse. Commutation outputs are available for 4-, 6-, or 8-pole brushless DC motors that eliminate the need for Hall Effect sensors, thereby reducing both processor time and bus traffic.
-
Product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for 4 M.2 PCIe SSD Modules
SKU-086-B4
-
B-series PCI Express Gen3 Carrier board was designed as a cost-effective storage solution for the systems that are using a motherboard with PCI Express bifurcation support. Such motherboards can be configured in the BIOS to split x16 PCI interface to four PCI Express interfaces by utilizing the following PCIe lanes:- x4 PCI Express interface 1: lanes 0,1,2,3 from x16 PCIe interface;- x4 PCI Express interface 2: lanes 4,5,6,7 from x16 PCIe interface;- x4 PCI Express interface 3: lanes 8,9,10,11 from x16 PCIe interface;- x4 PCI Express interface 4: lanes 12,13, 14, 15, from x16 PCIe interface;
-
Product
FPGA Boards
-
Take advantage of FPGA cards built on open standards and with a high degree of configurability in order to address a wide range of applications - without the expense and extensive development time of custom in-house developments.
-
Product
3.4 MP Autofocus Liquid Lens NVIDIA® Jetson TX2/TX1 Camera Board
E-CAM31_TX2
-
e-CAM31_TX2 is a 3.4 Mega pixel 4-lane MIPI CSI-2 liquid lens Auto focus camera board for NVIDIA® Jetson TX2 developer kit and it is also compatible with NVIDIA® Jetson TX1 developer kit. This camera is based on 1/3 inch AR0330 CMOS Image sensor from ON Semiconductor® with 2.2 µm pixel and A-Pix™ technology and an integrated high performance image signal processor (ISP). This S-Mount (M12) liquid lens camera enables autofocus with no mechanical moving part like VCM (Voice Coil Motors) will increase the lifetime and has an ability to focus and refocus in a matter of milliseconds.
-
Product
PCI To PC104 Extender Board
MS 1717
-
PCI to PC104/EPIC Extender card is used for extending the standard desktop PCI bus to compatible PC104 or EPIC bus. This will help to test all the PC104 cards through standard PC without any embedded processors. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the PC104 or EPIC boards.
-
Product
Single Board Computers
SBC35-427
-
WINSYSTEMS’ SBC35-427 is an industrial single board computer, which uses Intel®’s Apollo Lake-I E3900 series processor. Its combination of off-the-shelf functionality with multiple expansion and configuration options make it a great fit for industrial IoT applications.
-
Product
PCI Express A/D Board
AD14-500 Series - Dual 14 bit, 500 MS/s
-
The AD14-500 series has two 20-500 MS/sec 14-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at up to 4GB/sec (500MS/s * 2 bits per sample * 2 channels). Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual channel boards sample concurrently at the input clock frequency, and can also be software selected to run in single channel mode, providing twice the effective memory depth.
-
Product
PCIe/104 OneBank I/O Board
EMC²-7K160
-
Sundance Multiprocessor Technology Ltd.
The EMC²-7K160 is a PCIe/104 OneBank™ I/O Board with a Xilinx Kintex-7 SoM and a VITA57.1 FMC™ LPC I/O board. The PCIe/104 OneBank™ design enables the EMC²-Kintex-7 to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-Kintex7T also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
Product
Analog Input Expansion Board
MSXB 018
-
The MSXB 018 Analog Input Expansion Board expands 16 analog input lines to 64 analog input lines. The MSXB 018 provides 4 expansion ports that are compatible with MSTB 009 Analog Termination Boards.
-
Product
LAN (2ch) Expansion Board (supporting EtherCAT)
OP-SB89E
-
OP-SB89G is an expansion board for Ethernet LAN which is to be inserted into a slot of portable communication analyzer (LE-8200A/LE-8200). It has 4 LAN measurement ports and you can sniff 2 Ethernet lines at the same time by tap connection to capture packets on the 2 lines. It also can monitor input/output of a EtherCAT slave and measure the time delay cased by the slave.
-
Product
6U VPX double-GPU Image & Video Processing Board
VP69701
-
LinkedHope Intelligent Technologies Co.,Ltd.
Based on AMD Radeon™ E8860, VP69701 is a VPX double-GPU image & video processing board mainly designed for applications of embedded image & video processing and GPGPU.On VP69701, there are 4 independent display outputs routed to front and 2 GPU. Each GPU of VP69701 is equipped with 2GB GDDR5 video memory, 768/48 GFLOPS single/double precision peak processing ability and 640 shader processing units. VP69701 is highly suitable for HD output (1920x1080), 4K output (3840x2160), high-performance parallel computing and other applications and fields.
-
Product
Single Board Source/Meter/Switch
SMSU
-
SMSU Series SourceMeterSwitch Unit (SMSU), introduced by SW Link Ltd, is single-channel voltage/current sourcing, 4X6 switch matrix and measurement instruments. Each Series 100 SMSU instrument tightly integrates highly accurate stable DC power source and a true instrument-grade programmable gain amplifier and 18bits ADC on a 100x100mm PCBs. It can output up to 20V, sub-uA to 1A current to device under test (DUT)
-
Product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 5V
APCIE-1564-5V
-
32 digital inputs, 5 V, isolated16 interruptible inputs32 digital outputs, 5 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
I/O Board With Two COM, Four USB 2.0 And Audio For PICO840, PICO841, PICO842, PICO843
AX93283
-
*Specifications: 1 x RS-232/422/485, 1 x RS-232, 4 x USB 2.0, 1 x Audio (MIC-in/Line-out), 1 x power-on, 1 x Reset, 2 x LED*Dimensions: 118 x 29 mm*Compliant products: PICO840, PICO841, PICO843
-
Product
Test Lead, BNC Connector To BNC Connector Board
16048A
-
Extend the measurement port with a four-terminal-pair configuration that enables the attachment of user-fabricated test fixtures.
-
Product
2MP HDR Jetson TX2/TX1 Camera Board
E-CAM20_CUTX2
-
e-CAM20_CUTX2 is a 2MP HDR camera board for NVIDIA® Jetson TX2 /TX1 developer kit. It has an ability to stream seamlessly at wide temperature range (-40°C to 85°C). It enables an excellent low-light performance and can capture images even under 0.5 lux. e-CAM20_CUTX2 is based on 1/2.7" AR0230AT CMOS image sensor from ON Semiconductor™. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement.
-
Product
Single Processor COMe Carrier Board
NS11001
-
LinkedHope Intelligent Technologies Co.,Ltd.
NS11001 is a single processor COMe carrier board based on the Intel® AtomTM N270 platform.The board size is: 200mm x 184mm.NS11001 supports both PCI bus and ISA bus in order to be compatible with customers’ legacy peripheral interface cards like MVB. In addition, it consists of a 10.4-inch external TTL LCD panel and a matrix keyboard interface.Bined with COMe module, NS11001 embedded platform using Intel mobile processor N270, 945GSE + ICH7M chipset, and the maximum power consumption at full load is 10W.The system displays interface provides up to 1600 * 1200 resolution display output, and has a variety of interfaces such as Gigabit Ethernet, UART, USB, PATA, etc.NS11001 supports extended working temperature and can be used in harsh environment.
-
Product
3U CPCI MIL1553B Board
MS 1726
-
*Bus Interface:- 32 Bit PCI Bus with 3 U Form factor*PCI to PCI Bridge Interface*Speed of operation up to 66MHz*1 1553B dual redundant channel*4 RS422 Channels*16 TTL I/O Channels*Message Storage Buffer*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
Product
16-CH Discrete Input 16-CH Discrete Output Daughter Board Module
HSL-DI16DO16-DB-NN
-
- Slave ID consumption: 1 16-CH NPN sinking type sensor inputs or dry contact and 16-CH - NPN sinking type outputs- Photo couple isolation voltage: 2500Vrms- Input impedance: 4.7KΩ- Input current: ??10mA(Max), ??12.5mA(Peak)- Input voltage: ??40V (Max)- Output switching capacity:300mA/ch at 24VDC- Terminal Base:HSL-TB64 or HSL-TB32-DIN- LED indicator: Power, Link and I/O status
-
Product
VME / VME64x Load Board 6U
1940000140-0000
-
The Elma Electronic VME / VME64x load board provides a means to test the power generated by and cooling capability of VME systems. This makes it easier to locate hot spots in the chassis, so the airflow can be properly directed.
-
Product
3U VPX VITA 66.5 FPGA board with FMC+ Site
IC-FEP-VPX3f
-
Based on the latest Xilinx Kintex® UltraScale™ 20nm FPGA family, the IC-FEP-VPX3f is the first VITA 66.5 compliant FPGA board available. It is the perfect solution for applications requiring DSP-intensive processing in a 3U VPX form factor.
