Bare Board
is a printed wire board only.
See Also: Bare Board Probes, Bare Board Testers, Bare board Fixtures
-
Product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 5V
APCIE-1564-5V
-
32 digital inputs, 5 V, isolated16 interruptible inputs32 digital outputs, 5 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
Interface Module for the Multimode, Multiprotocol Excalibur 400 Family of Carrier Boards
M4K1553Px(S)
Interface Module
The M4K1553Px(S) interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.Each M4K1553Px multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M4K1553Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.Each M4K1553PxS single function (RT validated) module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.
-
Product
Digital Input Board
VME-1128
Digital Input Board
VME-1128 is a 128-bit High-Voltage Digital Input Board with Built-in-Test. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297) with the following mnemonics: A24:A16:D32/D16/D08 (EO): Slave: 39/3D:29/2D Form factor: 6U
-
Product
CAN Interface Board
-
- Auto Learning for slow detection and easy commissioning.- Encoder signal for floor detection.- Detail diagnostic of individual components ensures safety and reliable operation- Attached ARD for each panel for rescue in case of power fail.- Intelligent algorithm to attend any calls within 10 seconds for standard configuration.- VIP option, Fireman switch, overload protection $ protection of all other standard interfaces integrated.- Announciator is integrated with Gong bell.- Preferable selection of floor by user, software functional options, Delay times and important configurations.- Error diagnosis by PC interfaces, eleavator error history and services details make your maintenance job very effective and efficient in time period
-
Product
Multi-Protocol Board
EXC-8000cPCI
-
The board supports up to 6 modules, and each module represents an independent test and simulation device. Most modules are based on existing Excalibur products such as the 1553 Px family and the ARINC429 RxTx.
-
Product
VME / VME64x Load Board 6U
1940000140-0000
-
The Elma Electronic VME / VME64x load board provides a means to test the power generated by and cooling capability of VME systems. This makes it easier to locate hot spots in the chassis, so the airflow can be properly directed.
-
Product
Analog Backplane Interface Board
MSXB 029
-
The Microstar Laboratories Analog Backplane Interface Board, part number MSXB 029, interfaces the Analog Backplane with a Data Acquisition Processor. The Analog Backplane Interface Board must be installed in the Analog Backplane to connect the backplane to a Data Acquisition Processor.
-
Product
14-bit 16 Concurrent Channel 65MSPS A/D board
AD14-65Mx16AVE
-
14-bit 16-concurrent channel 65MSPS A/D board for demanding large-system uses, where signals on multiple time-aligned channels need to be observed with high SNR, such as RADAR, nuclear instrumentation, ultrasound, medical imaging, spectroscopy, communications systems, RF component and antenna testing and other critical applications. An on-board low-jitter LMX2581-based RF synthesizer allows any A/D sampling rate between 20MSPS and 65MSPS to be specified in software. A second on-board LMX2581 with synchronized reference can be optionally used to output four stimulus clocks on SMA connectors that can be vectored to any combination of 4 external transmitters, microwave pulse generators, laser modulators, and other devices.
-
Product
Interface Module for the Multimode, Muliprotocol Excalibur 8000 Family Carrier Boards
M8K1553MCH
Interface Module
The M8K1553MCH interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.The M8K1553MCH contains 32k x 16 of dual-port RAM for Data blocks, Control registers, and Look-up tables. All Data blocks and Control registers are memorymapped and may be accessed in real time. The dual-redundant 1553 module may be programmed to operate in one of four modes of operation: Bus Controller, Remote Terminal, RT/Concurrent-Bus Monitor, and Bus Monitor. The M8K1553MCH comes complete with Windows software, and a C driver software library including source code.
-
Product
DG I/O Backplane Extender Board
9286-1015
-
15" x 15" Backplane Adapter. Not to be used in production environment. Used with any I/O bus adapter during installation of Hawk system. Presents Nova/Eclipse bus signals on dual 50-pin connectors. Two 10 ft. (3 m) ribbon cables included.
-
Product
Pico-ITX
RSB-3410
Single Board Computer
*NXP ARM Cortex-A9 i.MX6 Dual Lite 1 GHz high performance processor*Onboard DDR3 1 GB, 4 GB eMMC Flash*Supports OpenGL ES 2.0 and OpenVG 1.1 hardware accelerators, full HD 1080p video codecHDMI 1920x1080*Single Channel 18/24 bit LVDS*Dual mini-PCIe for WIFI/3G support*1 USB 2.0, 1 USB OTG client*Multiple OS support in Linux/Android
-
Product
BMP-3 Board Marker Probe
BMP-3
ICT/FCT Probe
Current Rating (Amps): .05Voltage Rating (VDC): 15Recommended Duty Cycle: 1 sec. On (min.), 5 sec. OffTest Center (mil): 1,300Test Center (mm): 33.02Full Travel (mil): 62Full Travel (mm): 1.57Recommended Travel (mil): 50Recommended Travel (mm): 1.27Full Marker Travel (mil): 62Full Marker Travel (mm): 1.57Direction of Rotation: CCWScribed Diameter (mil): 50Scribed Diameter (mm): 1.27Rec. Mounting Hole Size (mil): 610Rec. Mounting Hole Size (mm): 15.50Recommended Drill Size: 39/64 (in) or 15.50 mm
-
Product
8k Frame memory Board
GG-169
-
GG-169 is a frame memory board that supports high-speed data transfer and can input and output uncompressed 8K video.With 12G-SDI × 4 lines (up to 8 lines with the use of an optional expansion board) equipped as standard, it achieves real-time output of 8K / 59.94p.
-
Product
BMP-4 Board Marker Probe
BMP-4
ICT/FCT Probe
Current Rating (Amps): .020Voltage Rating (VDC): 12Recommended Duty Cycle: 2 sec. On (min.), 3 sec. OffTest Center (mil): 1,000Test Center (mm): 25.40Full Travel (mil): 79Full Travel (mm): 2.01Recommended Travel (mil): 50Recommended Travel (mm): 1.27Full Marker Travel (mil): 62Full Marker Travel (mm): 1.57Direction of Rotation: CCWScribed Diameter (mil): 50Scribed Diameter (mm): 1.27Test Center Remark: Ø .398 (10.1) or M10
-
Product
MicroComU Board
-
The MicroComU board is designed to facilitate the adoption and use of the microDXP. To this end, the MicroComU includes various features to support and extend the functionality of the MicroDXP board. The MicroComU is designed to mate to a MicroDXP and be used as a set.
-
Product
Board Level CrossLine Generator
BL-CL5400A-11
-
Precision CrossLine or Crosshair Generators from MicroImage Video Systems are designed for relative size measuring, positioning and size referencing. The CL5400C series is especially helpful in industrial, metallurgical or forensic applications where comparisons in relative position or size are important.
-
Product
PCIe I/O & Comm Board
79C3
Multifunction I/O
NAI’s 79C3 is a PCIe Multifunction I/O and Communication Board with three independent function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
I/O Board With One GbE LAN, VGA And DC Jack For PICO841, PICO843
AX93267
-
*Specifications: 1 x DC jack, 1 x VGA, 1 x Gigabit LAN*Dimensions: 100 x 26 mm*Compliant products: PICO841, PICO843
-
Product
Development Board
SOM-DB2510
-
Development Board for SMARC V2.0/V2.1.1 Pin-Out Modules. Support SMARC V2.0/2.1.1 Module, Display Type: LVDS / eDP, HDMI / DP. Support eSPI, CAN-FD, USB3.2 & up to 14 GPIO, Support 4 Types Power Input. Integrate x86 and ARM Power Input Type.
-
Product
Boards
MIL-STD-1553
-
The MIL-STD-1553 multi function interface cards are compatible with all common variations of MIL-STD-1553 and provides a wide range of features normally found only on full size testers. The card can operate simultaneously as a Bus Controller (BC) and/or multiple (up to 32) Remote Terminals (RT), or as a Triggerable Bus Monitor. The card supports error injection and detection.
-
Product
FPGA Boards
-
For over two decades, Digilent has proudly worked with Xilinx to become a global leader in the design and manufacturing of cost-optimized field-programmable gate array (FPGA) and System on a Chip (SoC) development boards. Optimized for accessibility and flexibility, our control system boards are suited to a wide array of applications ranging from embedded vison and sensor fusion to networking and RF to embedded measurement and control systems. Enjoy high performance-to-price ratio, ease-of-use through onboard peripheral support, extensive documentation and example designs, and an open-source philosophy.
-
Product
XMCspan XMC Expansion Board
XMCspan
-
The XMCspan allows users to customize and expand I/O options when coupled with VMEbus SBCs, adding up to 4 XMC or PMC slots.
-
Product
Multiprotocol P104Plus Interface Board for Embedded Applications or Avionics Test & Simulation Applications
EXC-4000P104plus
-
The EXC-4000P104plus is a multiprotocol P104plus interface board for embedded applications or avionics test and simulation applications. Each board holds up to five independent modules. Two on-board modules use the MIL-STD-1553 communications protocol (M4K1553Px); another on-board module uses the ARINC-429 communications protocol; two additional detachable modules can be any one of the following types:M4K1553PxS (Single Function - RT validated) This module operates as a Bus Controller, Remote Terminal or a Bus Monitor. This module qualifies for airborne applications.M4K1553Px (Multi Function) This module operates as a Bus Controller, up to 32 Remote Terminals and as a Bus Monitor. Supports an Internal Concurrent Monitor in RT and BC/RT modes.M4K1553Px(S)-1760 Same as M4K1553Px(S) plus MIL-STD-1760 options.M4KMMSI Mini Munitions Store Interface module. Supports RT, BC/Concurrent-RT/Concurrent Monitor and Bus Monitor modes. Up to 8 hub ports EBR-1553 [10 Mbps 1553 protocol using RS-485 transceivers] and 1 monitor output.M4KH009 Based on our H009 family. This module operates as a Central Computer Complex (CCC) and/or up to 16 Peripheral Units (PUs) simultaneously, or as a Bus Monitor. In addition, a Concurrent Bus Monitor enables concurrent monitoring of the bus during CCC and PU simulation.M4K429RTx Based on our ARINC 429RxTx board. This module supports either five or ten ARINC 429 channels each of which can be configured in real time as a receive or transmit channel.M4K708 This module supports two channels of ARINC 708/453, each one selectable as either transmit or receive.M4KSerial This module supports up to 4 independent channels of serial communications, each of which can be selected as RS485, RS422 or RS232.M4KDiscrete This module supports 20 selectable input/open collector output discretes. The module supports TTL (0 to 5 volts) or avionics (0 to 32 volts) voltage levels.M4KCAN This module supports up to 6 independent channels of CAN 2.0B protocol with standard and extended message frames and message identifiers.
-
Product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 24V
APCIE-1564
-
32 digital inputs, 24 V, isolated16 interruptible inputs32 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
6U Processor Board
CP62103
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62103 is a modular design, based on COMexpress® technology, up to 4-core i7 processor from Intel® Ivy Bridge family. CP62103 is designed to meet harsh environment applications like rural communication, military, medical and outdoor video processing.CP62103 supports up to 3615QE, an Intel® 4-core processor. The 3rd generation Intel® Core™ i3/i5/i7 processors have a completely new microarchitecture, enabling small-sized designs to be created with unmatched computing power, graphics performance and energy efficiency on a small footprint.
-
Product
6U VPX Single Board Computer
VPX6-187
-
Curtiss-Wright Defense Solutions
The VPX6-187 VPX Single Board Computer (SBC) is based on the NXP QorIQ P4040/4080 SOC multi-core processor. Available in versions with 4 or 8 cores running up to 1.5 GHz, and up to 8 GB of high-bandwidth DDR3 SRAM, the VPX6-187 SBC provides high-performance processing and a long list of features and I/O interfaces to satisfy the most demanding requirements of embedded computing.
-
Product
XMC Gigabit Ethernet Boards
-
High-performance 1/10-Gigabit Ethernet interface solutions for real-time and COTS data streaming applications. XMC modules provide a rugged, embedded computing platform for high-speed data communication in defense, aerospace, and industrial systems. Implementing a TCP offload engine (TOE processor) fully in hardware relieves the CPU from TCP/IP overhead and frees it to perform other tasks.
-
Product
Nano-ITX Embedded Board
-
The Nano-ITX form factor is designed as a high integrated native x86 embedded platform, measuring a mere 120 mm x 120 mm which measures in at 50% smaller than the Mini-ITX form factor. The Nano-ITX form factor is available with a rich feature set and is targeted at the fast-emerging embedded markets, allowing developers to highly customize their system designs in the low-profile and fully-configured embedded devices.
-
Product
Squid PCI Express Carrier Boards™ for MiniPCI Express Modules
-
Amfeltec Squid PCI Express Carrier Boards™ for MiniPCI Express Modules
-
Product
Data Acquisition Board
DAP 4200a
-
The DAP 4200a is an excellent choice for applications where there is a need for real-time processing of data in the time interval between samples, and for applications requiring fast sample rates. Much of the DAP 4200a design is similar to that of the DAP 3200a/415, but the DAP 4200a has a PCI host interface, and is capable of high speed data transfers to the host PC.
