Bare Board
is a printed wire board only.
See Also: Bare Board Probes, Bare Board Testers, Bare board Fixtures
-
Product
Isolated Digital Expansion Board
MSXB 078
-
The Microstar Laboratories Isolated Digital Expansion Board, part number MSXB 078, provides isolated digital expansion for Data Acquisition Processor (DAP) systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – and eliminate timing errors from high-channel count digital I/O.
-
Product
TI HDC1080 Humidity and Temperature Sensor Breakout Board
SEN-37001
-
Breakout board for the Texas Instruments HDC1080. This sensor is an extremely accurate temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT2x series, and improves upon the success of the HDC1050. In addition, the HDC1080 has a wide input voltage range of 3V-5V and includes temperature and airflow cutouts as recommended for the best operation. Finally, in the case of environmental changes that could cause light condensation, the HDC1080 has a built-in heater to burn off any condensate. Example code (Arduino platform) is available below.
-
Product
Ethernet Digital Interface OEM Board
8063
-
* Same Digital IO lines as standard 8063. * Same data transfer capabilities as standard 8063 * Digital I/O uses high-density DC-62 connector.* Power connections via 2 screw terminal strip or solder pads.* User configured IDN message and webserver pages makes board respond as part of your system.* Use an ICS Wiring Kit to extend the Ethernet signal to a rear panel RJ45 jack.* Runs on 9 to 32 Vdc power.
-
Product
Isolated Watchdog Board
APCI-035
-
The board ADDIMULTI APCI-035 is equipped with 4 watchdogs allowing the simultaneous monitoring of multiple processes. Watchdog N? 1 works with 2 alarm levels and can be set to 1 of 4 different time bases (µs, ms, s, min). Level 1 alarms the PC cntrol and/or the monitored device. Level 2 resets the PC and/or the monitored device after a defined time. The alarm control can be accessed through 1 trigger channel and 4 different time bases.
-
Product
MIL-STD-1553 Two-Channel PMC Board
BRD1553PMC-STD-2
-
The PMC HyperBoard is a multi-standard PCI Mezzanine Card that contains two channels of MIL-STD-1553 communication. The board is compatible with MIL-STD-1553B and MIL-STD-1760. Each channel can be configured independently to work with H009 and WB-194 in conjunction with MIL-STD-1553.
-
Product
Board Connectors
-
Advanced Interconnections Corp.
High density designs maximize board spaceScrew-machined terminals for superior performanceSurface mount, spring pin, and thru-hole solutions
-
Product
Industrial Grade PCI DIO 96 Board
MS 1817
-
*96 digital input/output lines*Support s all PPI Modes (Mode0, Mode 1 and Mode 2)*5 V TTL/CMOS*Compatible with NI DIO Card*2-wire handshaking capability*Known power-up
-
Product
CPCI Or PXI PCM & ARINC 717 Board
MS 1703
-
*Bus Interface - PXI / CPCI Bus*Microprocessor and FPGA design based Board*One Channel ARINC 717 Transmitter and Receiver*Generates all PCM telemetry signals like NRZ, Bi-Phase, Differential Bi-phase, DM signals*Used to test all types of PCM based telemetry equipments*Configurable output signals format (parity, word length, Minor, Major frame, Bit position)*User can configure the words and there positions in the frame*The word can be either a square / triangle wave data or constant data*1 MB Shared Memory for Data Storage*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
6U VPX UltraScale™ FPGA board with FMC+ sites
IC-FEP-VPX6e
-
Based on the latest Xilinx Kintex UltraScale™20nm FPGA, the IC-FEP-VPX6e is a 6U OpenVPX Front-End Processor (FEP) optimized for applications requiring DSP intensive processing in highly constrained environments.
-
Product
ARINC-664 Part 7 Test and Simulation Board
EXC-664PCIe
-
The EXC-664PCIe board is an ARINC-664 part 7 test and simulation board designed to help integrate avionics suites, and can simulate up to two ARINC-664 P7 End Systems with full dual redundant support for receive and transmit operation. The board also contains room for two standard 4000 modules that can support multiple channels of other avionics communications protocols including MIL-STD-1553, ARINC-429, Serial, Discrete, ARINC-708 and CANbus.
-
Product
Digital Output Board, 32 Isolated Channels, 24V
APCIE-2032
-
32 digital outputs, 24 V or 5 V, 500 mA/channel Optical isolation 1000 V Overvoltage protection Short-circuit protection WatchdogAt power-on the outputs are reset to ì0î
-
Product
12-bit, 100KHz, 8SE/4DIFF Isolated Analog Input Board
APCI-3001-8
-
8 single-ended or 4 differential inputs 12-bit resolution Optical isolation 500 V 100 kHz data transfer rate Automatic analog acquisition 8 digital I/O, 24 V, isolated, timer Trigger functions Graphical display of the measured data
-
Product
6U VPX Single Board Computer
VPX6-195
-
Curtiss-Wright Defense Solutions
Our VPX6-195 6U OpenVPX T2080 Single Board Computer (SBC) combines performance with the advanced I/O capabilities of the NXP's quad-core AltiVec enabled T2080 processor. Designed for SWaP-constrained applications, the VPX6-195 provides two independent processor cores on a single printed wiring board (PWB) with a wide range of standard I/O and each with a XMC mezzanine site to provide twice the processing power.
-
Product
Single Board Computer
VPX6-197
-
Curtiss-Wright Defense Solutions
Our VPX6-197 is an OpenVPX-compliant 6U SBC that combines the performance and the advanced I/O capabilities of the NXP’s quad-core AltiVec-enabled T2080 processor. Designed for space-constrained applications, the VPX6-197 combines the processing power of quad-core dual threaded 64-bit Altivec-enabled non-throttling computing with a rich I/O complement.
-
Product
Compact 3U CPCI Processor Board
CP32110
-
LinkedHope Intelligent Technologies Co.,Ltd.
Based on Intel® Atom™ x5/x7 E3900 series (Apollo Lake-I), Pentium® N4200 and Celeron® N3350 CPU, CP32110 is a compact 3U CPCI single board computer compliant with CompactPCI® specification.On CP32110, there is a Mini SATA interface for system software installation, and several peripheral interfaces include SATAII, USB2.0 and Giga bit Ethernet.
-
Product
Multiprotocol PCI/104-Express Interface Board
8000PCIe104
-
The EXC-8000PCIe104 is a multiprotocol PCI/104-Express interface board for embedded applications or avionics test and simulation applications. Each board holds up to four independent modules and 10 discrete channels.
-
Product
SparkFun IR Thermometer Evaluation Board
MLX90614
-
This is an evaluation board for the MLX90614 IR Thermometer. The sensor is connected to an ATmega328 running at 3.3V with a STK500 (Arduino) 8MHz bootloader. Code can be loaded through the FTDI basic interface and the Arduino environment.
-
Product
Meter Warm-up Board
3000/3001
-
The Catalog 300X Universal Meter Warm-Up Board is designed to go from the shop floor to a customer location. TESCO's Warm-Up Board is made from a high quality industrial fiberglass enclosure and is light and durable. TESCO's warm-up board is the portable, effective solution to your shop, vehicle, or remote meter warm-up needs.
-
Product
FMC Loopback Test Board
-
The FMC loopback tester board enables developers and assembly factories to test and characterize the FMC carrier board interfaces. The board features full differential loopbacks on all the FMC high pin count (HPC) connector interfaces including LA, HA, HB, DP and CLK. It also provides a 125MHz transceiver LVDS reference clocks on GBTCLK signals. The FMC loopback board is based on VITA 57 standard with ruggedized conduction or air cooling.
-
Product
6U Processor Board
VP62005LRM
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP62005LRM, designed for specific application area, is a processor board based on Intel® 6th generation E3 processor. VP62005LRM supports 4 cores and 8 threads, and through Intel® Turbo Boost technology, working frequency of VP62005LRM can immediately reach to 3.7GHz.With Intel® IrisTM Pro GraphicsP580(or HD530) installed on VP62005LRM, the graphic memory frequency can be up to 1.0GHz. VP62005LRM supports 4K display output, and the refreshing frequency can reach to 60Hz. In addition, VP62005LRM provides DirectX12, OpenGL 4.4, eDP/DP/HDMI/DVI output, and up to 3 independent displays.VP62005LRM supports 1 x8 PCIe 3.0, 4 x4 Rapid I/O (SRIO) and data exchange between ports of SRIO. In addition, VP62005LRM has 3 Gigabit Ethernet ports, with one port supports NCSI and can establish remote transmitting channels for massive data in the system. Rich interfaces and data communication ability on VP62005LRM makes it convenient for users to design computer and system solutions.
-
Product
Form A Circuit Board 80 Channel, 300 VDC, 2 A
OTP2 module no.195
-
The 40-139 2A relay series is suitable for applications requiring medium power, high density switching. With a current capacity of 2 A and voltages up to 300 VDC / 250 VAC, it is suitable for cost-critical applications.
-
Product
Digital I/O Board w/CoS IRQ
104-DIO-48S
-
*48 or 24 parallel lines of 82C55 digital I/O with tristate buffers prevent unintended control of external equipment*IRQ on input change of state (COS) eliminates the need for constant polling*High sink/source current 64mA/32mA*I/O pulled up to 5V for contact monitoring*Compatible with Opto-22 and other industry standard I/O racks
-
Product
X-ray Inspection Of PCB Boards And More
The RTX Series
-
Glenbrook’s RTX Series of modular, real-time systems include models designed to meet a variety of production requirements including circuit board components. Numerous options make it easy to customize any RTX model to your specific application. All hardware and software elements are fully compatible to ensure the continued value of your equipment.
-
Product
Configurable 3U OpenVPX Multifunction I/O Boards
Multifunction I/O
NAI offers a variety of 3U VPX solutions, including rugged I/O Boards and SBCs - designed to be combined with our smart function modules - to create a COTS-based, high-density, multifunction I/O solution for most sense and response requirements.
-
Product
Single Board Computers
PX1-C441
-
WINSYSTEMS’ PX1-C441 single board computer (SBC) is a PC/104 form factor SBC with PCIe/104™ OneBank™ expansion featuring the latest generation Intel Apollo Lake-I Dual-core or Quad-core SOC processors for processing graphics. It includes up to 8 GB of soldered down LPDDR4 system memory and a non-removable eMMC device for solid-state storage of an operating system (OS) and applications. In addition, the board supports M.2 and SATA devices.
-
Product
Digital Termination Boards
MSTB 008
-
For quick and secure connection of discrete wires to a Data Acquisition Processor (DAP) board, use the MSTB 008 Digital Termination Board.
-
Product
Pulse Initialization Demo Board
TMR9112
-
MultiDimension Technology Co.,Ltd.
The TMR9112 demo board was developed to support evalution of the TMR9112 single-axis sensor. The demo board comes with the fast bipolar current pulsing circuit needed for initialising the TMR9112 sensor, and it can be powered from a USB port or any external 5V power supply. For user convenience, the demo board has an optional on-board timer clock with four selectable frequency settings. The On-board timer clock and frequency output can be enabled using the jumper pins. This demo board is divisable along the dotted line so that the sensor board can be seperated from the pulsing circuit board.
-
Product
Single Board Computers (SBC)
-
Any Single Board Computer from WinSystems is an Off-the-shelf ARM and Embedded PC designed for rugged, industrial environments and long product life cycles. Our Single Board Computers are created and packaged under precisely controlled conditions and subjected to intensive quality control to ensure they perform under extreme conditions.
-
Product
3U CPCI I/O & Comm Board W/Gig-E Switch
75D4-H2
Multifunction I/O
The 75D4-H2 is a Layer 2+ Gigabit Ethernet Switch built upon NAI’s multifunction, 3U cPCI board technology. The 75D4 motherboard contains a high-density I/O module slot that supports an H2 switch function. The 75D4 with H2 consumes approximately 9.5 W of total power at 5 V to operate at full 1000 Base-T speeds. In addition, the 75D4 motherboard can integrate four channels of RS232/423/422/485 serial communications. This adds an additional 1.5 W of 5 V power. Serial data is available on the cPCI bus or can optionally be available over Ethernet via the use of one of the switch ports.
-
Product
50-Pin DIN-Rail Flat Cable Wiring Board
ADAM-3950
-
Low cost universal DIN-rail mounting screw terminal module for PC-LabCard™ products with 50-pin flat cable connectorCase dimensions (W x L x H): 77.5 x 146.3 x 51 mm (3.1" x 5.8" x 2.0")To Be Used With USB-4751/L, PCI-1737U, PCI-1739U, PCL-722, PCL-724, PCL-731
