High Voltage
electric power transmission is > 35,000 volts and for safety AC > 1000 and DC > 1,500. AKA: HV
See Also: High Voltage Switching, High Voltage Meters, High Voltage Detectors, High Voltage Programmable Power Supplies, HV
-
product
High Voltage Insulation Equipment
Wuhan Huatian Electric Power Automation Co., Ltd.
Electrical insulation testers for high voltage equipment.
-
product
1mV-300V / 2 CH. Milli-Voltmeter
Digital MVT-172D
Is applicable to measure RMS value of sine wave with frequency range 5Hz~2Mz and voltage range 100μV~300V. This instrument has a 4 digit display with high precision, small frequency effected errors and high input impedance. There are three display ways including voltage, dB and dBm, supplying a clear and intuitive display. Auto measuring range switching makes your usage more convenient. All switches are touch switches with high quality, providing good hand feeling and high reliability.
-
product
High Voltage Transformer
RR manufactures HIGH VOLTAGE TRANSFORMERS for various Industrial Applications.
-
product
PXI 2 Amp MUX, Dual 16-Channel 2-Pole
40-635-006
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
High Voltage Linear Amplifier
A400X
This unit is a version of A400 amplifier equipped with two inputs, DC-offset and output atenuation. Input A is a normal non-inverting one. Using this input alone makes A400X functionally identical with A400 amplifier.Input B can act as a inverting or non-inverting depending on the position of the corresponding switch.
-
product
Insulation Testers
Shenzhen Everbest Machinery Industry Co.,Ltd.
The insulation resistance (IR) test (also commonly known as a Megger) is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance.
-
product
Automatic Voltage Regulator – 1kVA to 3kVA
SVR-PL™ Series
*Convenient Rackmount/Tower Design*UL Listed for High Temperature Operation -30°C to +65°C (-22°F to +149°F)*True Sinewave Output*Input Power Factor Correction*Wide Input Voltage Window*Precision Output Voltage Regulation*Extended Brownout, Plus Surge & Transient Protection*Frequency Converter Option*High Temperature LED Display*RS-232C, USB & Optional SNMP/HTTP Agent
-
product
Bench Power Supply, DC, Single, Adjustable, 1 Output, 1 V, 36 V, 0 A, 3 A
72-8345A
Switch Mode Laboratory DC Power Supplies Precision adjustable supply provides adjustable 1~36VDC output with adjustable current limiting from 0~3A. It is ideal for test, measurement and service applications where tight voltage and current regulation are critical. Highly efficient switch mode design delivers outstanding performance from an extremely compact footprint. Unique separate output ON/OFF control allows voltage and current setting, with the supply output turned off. Part of a Complete Series, this slim supply occupies little bench space while providing very high precision and 90W of continuous output.
-
product
Voltage Pulse Generator
SKS-IV10J
Shanghai Sanki Electronic Industries Co., Ltd.
The voltage pulse generator SKS-IV10J is completely designed in accordance with the requirements of the impulse voltage chapter in OIML R 46-1/-2; it meets the requirements of the new IEC60255-5 and GB14711 standards; the leakage current detection alarm function is added, and the leakage current limit can be Adjustment; using linearized high-voltage power supply, low noise, high stability, high voltage accuracy and long service life.
-
product
AC and DC Current or Voltage Transducers
VT7 AND VT8 Series
The Model VT7 Series dc voltage transducer produces an output which is directly proportional to the input from dc to 10kHz. It functions as a millivolt dc shunt or a high voltage isolator to 1000V
-
product
High Voltage EMC Surge Generator
TM510
TM510 Surge Generator is mainly used for testing power cable high-resistance and arc-over fault whose grade range is 0-10kV, co-operating with cable fault tester and locating devices to test and locate faults. If the user choose the professional digital milli-ampere-meter, as for cable with grade range about 0- 6kV, the instrument can also be used to do DC&voltage resistance test and current leakage test after the fault is repaired. The instrument is internally equipped with voltage-rise rectifying and discharging device, has complete functions, and is also convenient and safe to be wired and operated.
-
product
Capacitor for AC Filtering
PECA4 (690V)
Lifasa - International Capacitors, SA
These capacitors are especially suitable for applications where high levels of AC voltage are required. The design of this series has been optimized for the manufacture of high performance AC filters for compensation equipment with high pollution such as UPS or wind turbines.
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Cut Ends, 1m, HV
A037DM5-C-HA100
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
High Voltage 9 Pin D-Type Cables - Connector to Connector for Pickering
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a high voltage 9-pin D-type connector.
-
product
Multiplexer
SC6540
Our patented SC6540 modular scanning matrix pioneered the largest productivity improvement in the electrical safety compliance industry in years. With up to 16 independent high voltage or high current channels in a convenient 2U design, the SC6540 can be customized in 10 different configurations for multi-point Hipot, Ground Bond, Insulation Resistance and Leakage Current testing.
-
product
PXI/PXIe High Voltage Multiplexer, Quad 5-Channel, 1-Pole
40-321-101-HI
The 40-321-101-HI (PXI) and 42-321-101-HI (PXIe) are quad 5-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
Bipolar Power Supplies High Power, 4-quadrant, Analog/Digital/Local Control, Low Ripple/Noise
Series BOP-MG/ME, BOP-EL/GL
The BOP High Power are true 4-quadrant programmable voltage and current power supplies. 4-quadrant operation means that they are capable of both sourcing and sinking power. These bipolar power supplies pass smoothly through zero to provide ± voltage and ± current. The BOP High Power use switch mode technology for low dissipation and function as regenerative (recuperative) loads and connected to an active load.
-
product
High Voltage Power Sources
Electronic Test & Power Systems
A comprehensive range of high voltage power sources are available from ETPS. Product families range from programmable high precision laboratory power supplies to HV Cassettes and PCB modules.
-
product
Electronic Speed Controller
AFI-ESC1220
The AFI-ESC1220 is an Electronic Speed Controller designed to drive BLDC motors. It meets the industrial requirements of high power and high voltage application for electronic vehicles, airplanes, boats and medium duty industrial machinery. It is rated at 24KW.
-
product
Shoe Dielectric Resistance Tester
UI-FT07
Shoe Dielectric Resistance Tester, also named as shoe high voltage withstand tester, is used to test shoe sole and heel electrical insulation, to check shoe performance of voltage withstand and current leakage. It is to test safety shoe dielectric resistance ability (Electrical Hazard Testing) as mentioned in ASTM F2412.
-
product
50 Pin D-Type Male without Backshell, HV
92-960-050-M-HV
This connector is designed to allow users to directly terminate cables with soldered connections. 50-Pin Female HV connectors can be directly mated to a corresponding Pickering Switching Module.
-
product
High Voltage Switching Test System
The advanced development of new technologies, such as SiC and GaN, have opened the opportunity for more efficient and higher voltage/power performance in switching and power management circuits. Their high cutoff frequencies, low on-state resistance, and very high breakdown voltages can increase power supply power handling densities approaching hundreds of watts/inch. Reliability of these new technologies and techniques is critical for realizing practical applications. While Silicon devices have...show more -
product
PXI 2 Amp Multiplexer, Dual 16-Channel, 2-Pole
40-635A-006
The 40-635A-006 is a dual 16-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
Parasitic Drain Tester
64970
Replaceable in-line fuses protect both the meter and tester in the event a high current source on the vehicle is left on. The multimeter is bypassed with the switch during connection in case of a power surge. The tester and meter can remain connected until other computer systems shut down, isolating the drain. As a convenience, stacking banana connectors are used on the tester. This allows voltage to be measured on various locations on the vehicle during the drain test, using standard test leads.
-
product
Digital Logic ICs
Renesas' general-purpose logic devices support the information equipment and computer fields, which demand small size and high performance. With a variety of power supply voltages, functions, and capabilities, these logic devices provide strong support for specialized applications such as bus switching, level conversion, and clock-related applications.
-
product
High Power Digital Lab Series Regulated DC Power Supply – 3000W
- 3000W different combination- High current density.- 19″ rack adaptable -5U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation Optional, at extra cost- Over voltage protection- 19″ rack mounting
-
product
2kV, 400 MHz High Voltage Differential Probe
HVD3220
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
product
Interface and Isolation
Analog Devices offers a wide range of digital interface and digital isolators with iCoupler® technology covering the industry’s field bus and peripheral communications standards. Digital isolators, isolated transceivers, isolated A/D converters and isolated gate drivers utilize the award winning iCoupler® and isoPower® technologies for isolation solutions without many of the constraints found in optocouplers. Find design solutions for interface devices including keypad controllers, level translators, and high voltage protection products (channel protection, fault protection, overvoltage protection), and latch-up proof switches and multiplexers.
-
product
PXI Semi-Dynamic Digital I/O Module, 32-Channel
40-419-003
The 40-419-003 is a 32-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
product
VLF Diagnostics System
PHG 70 TD
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PHG 70 TD. The combination of the PHG 70 programmable test generator with the BAUR dissipation factor measurement system produces the cable testing and diagnostics system PHG TD. It is operated via PC control. Dissipation factor measurement and diagnostic testing sequences can be programmed in the menu, after which the dissipation factor measured values are automatically determined in various voltage steps and a final evaluation is conducted.* Biggest ...show more
