-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-200B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
Rugged Cabinet
MS Series
The M-Series MIL-STD Cabinet offers a high level of integrity with its all-welded 12 gauge steel frame construction, and eight, 3-dimensional support braces (12 gauge), providing added resistance to demanding compressive and torsion loads.
-
product
Automatic Metallic Pendulum Impact Testing Machine
Jinan Testing Equipment IE Corporation
JB-450/750A automatic type pendulum impact tester is used to determine the impact resistance of metal materials under dynamic load and is capable of doing a large number of impact tests continuously. The automatic type pendulum impact tester can display the impact power, impact toughness, and the pendulum's rotation angle. All the testing reports can be printed out. JB-450/750A can be equipped with fully automated sample feeding system, which greatly improves the test efficiency, and reduce labor intensity. The crygenic cooling device is available for impact tests under the lowest temperature down to -196 C. The automatic type pendulum impact testing system is the essential quality control equipment for metal material manufacturers and QC departments, as well as the necessary instrument of research institutes for new material research.
-
product
High Accuracy AC Reference Source
515
Clarke-Hess Communications Research
The Model 515 High Accuracy AC Reference Generator fills a need for a relatively low cost and practical solution for supplying a reference excitation to typical LVDT and Synchro/Resolver transducers. The Model 515 has built-in load sensing which, in effect, yields "zero" output impedance and virtually eliminates the effects of fluctuating output loads. With up to 15 VA of output into loads with as much as 80 of phase shift, the Model 515 is ideally suited to driving inductive loads.
-
product
Regenerative DC Electronic Load
IT8300 Series
ITECH newly launched IT8300 Regenerative DC Electronic Load, it not only can simulate various load characteristics, but also can feed power back to grid without pollution. IT8300 series unique regenerative function can convert the absorbed DC power into AC power and feed it back to local grid.
-
product
Pin Brinell Tester
Newage Testing Instruments, Inc.
The Pin Brinell is a cost effective instrument, which uses a calibrated shear pin to control the amount of load applied. Provides consistent loading regardless of operator. Tests in 100 - 730 equivalent Brinell range.
-
product
C-Mic Auto Test System
BK9010B
Based on the BK3010V2 C-Mic Tester, the BK9010B is our fastest C-mic test system. Fully automatic, the BK9010B loads the mics in place and after testing, it sorts passing microphones into 8 quality classes, and failing microphones according to the reason they failed. Each mic is put into its appropriate bin. As testing progresses, you can view the data graphically in real time or save it to be viewed or analyzed later.
-
product
Heavy duty pull tester for roofing - 1000 lb
FIXUROOF 1000
The Fixuroof 1000 portable pull-tester is an accurate unit, designed for testing in the field the pull-out force for base ply fastener. Easily determine whether the mechanical fastener provides sufficient resistance to static uplift force to meet the wind load requirements.
-
product
Power Line Isolators & Conditioners
A power line conditioner (also known as a line conditioner or power line conditioner) is a device intended to improve the quality of the power that is delivered to electrical load equipment. While there is no official definition of a power conditioner, the term most often refers to a device that acts in one or more ways to deliver a voltage of the proper level and characteristics to enable load equipment to function properly.In a nutshell, poor incoming electrical power converted to good output power.
-
product
Automated Breakthrough Analyzer
ABR
The ABR is a dedicated breakthrough analyzer with fully programmable operation including control of total pressure, flow rate, composition and temperature. Samples are loaded into interchangeable reactor beds and dried in-situ with purge gas or vacuum at elevated temperature. Reactive gas mixtures are then flowed through the bed, and the downstream composition determined in real-time with an integrated mass spectrometer.
-
product
Load Cells & Mounting Kits
Load cells are commonly used to measure weight in an industrial environment. They can be installed on hoppers, reactors, etc., to control their weight capacity, which is often of critical importance for an industrial process.
-
product
Thurst Reverser Cowl Actuator
The Thrust Reverser Cowl Actuator is a single-acting telescoping actuator used to open the thrust reverser cowl doors on the A320neo engine nacelle. The actuator has one port for extension with retraction being accomplished by the cowl door weight. The inner piston includes a hydraulic lock feature that will stop the cowl door opening due to the wind load case of 40 knots pulling the door open.
-
product
PET Bottle Vertical Load Tester
VP-1000
VP-1000 PET Bottle Vertical Load Tester is professionally designed to test the top load resistance, container body side load resistance of the PET container.
-
product
Electrostatic Capacitance-Type Gap Detectors
VE series
VE series are non-contact type of vibration/small displacement detector with high accuracy which can measure the distance between conductor such as metal and sensor’s surface in micron/submicron resolution. It demonstrates its best performance when used for the measurement and control of the axial and surface vibration of rotational shafts such as main shaft of turbines, electric motors, compressors, and of the thickness and width of moving objects. In addition to the measurement of the amount of displacement, a gap detector can also be used for a wide range of other measurement and control applications such as the measurement of the amount of slack or warping. The non-contact measurement process enables to apply no load to rotational or vibration body, and does not affect the material under measurement.
-
product
Live Recorder
Live Recorder allows Linux programs to make a detailed recording of themselves while they are running, and to load the resulting Undo Recording in a specially configured UndoDB - our reversible debugger for Linux. An Undo Recording allows UndoDB to completely reconstruct everything a program has done, including every memory access and every instruction executed. By using Live Recorder, developers can debug an exact copy of the original program''s execution, allowing them to track down bugs without needing to reproduce them in-house, write test cases or make time-consuming visits to customer sites.
-
product
Power Supply QD305 2x30V/5A
*on / off switch output section*two independent adjustable DC output*independent outputs serial and parallel*constant voltage and current*Low ripple and noise*four digit LED displays three*for 16 hours at full load*automatically search out
-
product
The DC System Analysis Module
Save time with intuitive scenario manager interface.• Communicate designs effectively with graphical and text base results.• Improve decisions by quickly comparing resulting curves from different scenarios.• Increase productivity by modeling both DC and AC systems in a single project.• Reduce mistakes by evaluating all loading conditions and duty cycle loads.
-
product
1 GHz, 1 MΩ, 0.9 pF Active Probe
ZS1000
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS1000 is ideal for 200–600 MHz oscilloscopes.
-
product
Energy Monitoring
Our Energy Monitoring products keep you well-informed of how much power you use, what your major loads are, when you use electric power the most, how much you pay for it, and the quality of the power you use. Use these Energy Monitoring hardware and software products to improve your equipment productivity and life, reduce your power use and its costs, and increase your company's profits.
-
product
Controllable, Programmable Linear DC Source With Load
LAB / SL
*Linear laboratory power supply*Integrated electronic load*Linear regulated DC laboratory power supply*No thyristor pre-regulation, very little ripple*Various interfaces · Built-in electronic load*Protection against short circuit, overload and overtemperature*Constant current and constant voltage*Fast control times approx. 250 µS
-
product
Analog Tensile Testing Machine
It can test materials like rubber, wood, plastic, rexins, teflon, cardboard, composites, ferrous metals, non-ferrous metals etc.Wide range of Grips, Attachments & Special fixtures are available to suit varieties of material and shapes. Continuous roll autographic Load Vs Elongation recorder.Continuous roll autographic Load Vs Elongation recorder.Elongation scale with least count 1 mm.Elongation scale with least count 1 mm.Three measuring ranges for accurate testing.Three measuring ranges for accurate testing.A number of straining speeds are available for proper selection.A number of straining speeds are available for proper selection. Machine with AC or DC drive motor is available.Machine with AC or DC drive motor is available.Various Models – Maximum Capacity from 200 N to 50 kN.Various Models – Maximum Capacity from 200 N to 50 kN.Loading accuracy well within ±1%Loading accuracy well within ±1%Hand operated cutting press with different sizes dies are available for cutting dumbbell specimen.Hand operated cutting press with different sizes dies are available for cutting dumbbell specimen.
-
product
DC Load Banks
Custom DC Units
Mosebach Manufacturing Company
Mosebach has been building DC load banks for over 30 years. We have a wide range of custom-designed units. Please give us a call at 1-866-629-4328 to discuss your needs.
-
product
Electronic Loads
T3EL Series
The T3EL series is a family of single channel, 200 & 300 Watt Electronic Loads that are ideal for R&D, product validation and Q&A in a bench or automated environment for low to medium power applications starting from 60mA, such as electronic components, batteries, portable chargers and power products. Electronic Loads are typically used to provide a load to the outputs of a power supply, usually capable of dynamic loading, and are fully programmable. Electronic Loads help designers to test electronic power products and ensure quality, reliability, and performance.
-
product
MCB Endurance Test Bench
The SCR Elektroniks Endurance Test Bench is designed for electrical and mechanical endurance MCB and RCCB as per clause 9.11 of IEC 60898-1. The source and the load is designed to comply as per the general test conditions specified in Cl 9.11.1. The accompanying pneumatic fixture is designed to hold custom built designs of MCB and RCCB while the microcontroller based timer unit can be configure to follow test procedure summarized in Cl 9.11.2.
-
product
PXI/PXIe Power Relay Module, 18xSPST, 5 Amp, 50-pin SGMC Connector
40-153-004
The 40/42-153-004 is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A. User connection is via a 50-pin SGMC male connector. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
product
PXI Electronic Load Module
PXI Electronic Load Module provides the electronic load capabilities of sinking DC power with high-accuracy measurements in a compact form factor optimized for design validation, characterization, and production test.
-
product
Modulators
ZMOD-X1
Antenna Technology Communications, Inc.
The ZMOD-X1 modulator series is an all inclusive unit that is loaded with features most needed by broadcasters. In it's most basic form, the unit comes with DVBS, DVBS2 and 8PSK modulation schemes, IF output, L band output and ASI input all as standard features. 16 APSK modulation and IP input are provided as options. Taking mobile and portable systems in mind, the unit comes with clear and user friendly front panel control. Size and weight are significantly less than any unit on the market. The unit can also be monitored and controlled using any web browser.
-
product
Automatic Engine Balancing Technology
AutoBalance™ System
Continuously adjusts fuel flow to each power cylinder to maintain balanced operationMinimize emissions and fuel consumption over a wide range of operating loadsReduce mechanical wear and maintenance costsReduce personnel costs and risk by eliminating manual engine balancingSupports engines with up to 20 power cylindersOn-Guard Diagnostic software for monitoring, analysis, reporting and trendingSupports automated air manifold pressure control for minimum emissions at varying loads
-
product
Load Cells and Sensors
Our high quality load cells and sensors are used for materials testing and force measurement all over the world.
-
product
Digital 130AMP Battery/Alternator Tester
MD4780
For testing 6V and 12V batteries, charging systems, alternator diodes and starter. Industry leading 130 amp load .
