-
Product
Linear Testfixture for Pylon Mass Interconnected Cassette interface (Cassette Not Included) 6 Positions Blocks, UUT 306 x 248 mm
MG-02-01 Pylon Genrad VG series
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 6 interface blocks of 170 signals• All interface blocks can be customized
-
Product
In Line Load Cell (200N-5000N)
100 Series
-
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 5000N with better than ±0.25% non-linearity.
-
Product
Active Filter
J2190A
-
The J2190A active filter presents a high impedance (approximately 150kOhms) minimizing the loading of the circuit being tested. The output impedance is 50 Ohms allowing low noise coaxial connections to all typical test equipment. The 0.1Hz-10Hz noise band is common for opamp measurements, voltage regulators and voltage references. Many application notes offer schematics of such a filter for test purposes. An engineer’s time is much too valuable to be spent building test equipment. We have created a 4th order high pass and 4th order low pass filter with an optimally flat response and 0dB gain. Additional filters can be cascaded for even sharper cutoff.
-
Product
Regulators
-
The voltage regulators made by Ducati Energia are combined with permanent magnets alternators in order to manage both the battery charging and the direct supply of AC loads (lights, cooling fan, etc).
-
Product
Structural Load Monitoring
SLM
-
Since 2001 ITM has installed structural strain based monitoring systems in the pulp & paper and energy generation industries. For these systems, our engineers and field service technicians turn structures into measurement instruments (load cells). Load outputs from the structural load cells are monitored and published by a realtime controller to its local interface or network historians and HMIs.
-
Product
PXI/PXIe Power Relay Module, 3xSP4T, 20 Amp
40-166-201
Relay
The 40/42-166-201 is a PXI/PXIe high density power relay module with 3xSP4T switches rated at 20A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations. It uses power relays which are suitable for switching loads up to 20A at 240VAC (SPDT & SP4T versions) or 30A at 277VAC (SPST versions).
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1000B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
AC Load Banks
XL1000-XL1250 Series
-
Mosebach Manufacturing Company
The XL1000-XL1250 Series load banks offer you a continuous load at various voltages in a compact, lightweight enclosure.
-
Product
Mini Low Profile Load Cell Universal/ Tension or Compression
MLP SERIES
-
The model MLP Series load cells were designed with economy as first priority. They are a scaled down version of our successful LPO Series Load Cells. MLP-10 through MLP-300 are anodized aluminum and the MLP-500 through MLP-1K are made from 17-4ph heat treated stainless steel. The unique low profile design of the MLP Series provides excellent stability for in line applications for tension and/or compression, while saving space at the same time.
-
Product
Compact Three-Phase Ppower Capacitor
MFB
-
Lifasa - International Capacitors, SA
These capacitors are especially suitable for the compensation of inductive loads and for the construction of automatic batteries.
-
Product
Time Domain Reflectometer
ETDR 10A-C
-
Compact dual channel precision full function portable easy to useTDR for fault location on balanced loaded and unloaded cables.
-
Product
Solid-State Demand Recorder
SSR-6000
-
The TransData SSR-6000 is a Load Profiling Interval Pulse Data Recorder used for recording and profiling pulse data received from electricity, gas and/or water meters. The SSR-6000 features a cover-mounted optical port and remote communications via integrated digital cellular, ethernet, telephone modem or RS232 communications options; and includes totalizing capability for aggregated metering applications.
-
Product
PXI Electronic Load Module
Load Module
PXI Electronic Load Module provides the electronic load capabilities of sinking DC power with high-accuracy measurements in a compact form factor optimized for design validation, characterization, and production test.
-
Product
PXIe-4147, 4-Channel, ±8 V, 3 A Precision PXIe Source Measure Unit
786888-01
Source Measure Unit
PXIe, 4-Channel, ±8 V, 3 A Precision PXI Source Measure Unit - The PXIe-4147 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote four-wire sensing for accurate measurements. The sample rate of the PXIe-4147 can reduce measurement times, capture transient device characteristics, and help you perform current-voltage (I-V) characterization of devices-under-test (DUTs). With a high-speed sequencing engine, you can synchronize SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4147 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
T3DSO Passive Probe, 350 MHz, 10X, 10 MOhm, 300V/600V
T3PP350A
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
Product
500 AMP Carbon Pile Load Tester
CP710
-
Tests batteries rated as high as 1000 CCA or 160 amp hour. Also tests alternators, regulators, and starters
-
Product
Digital Control DC Electronic Load
IT8200 Series
-
IT8200 series economical programmable electronic load,with the highest cost/performance ratio and small size, they are widely used in production testing lines and maintainance lines etc. Resolution 1mV/1mA ensures the accurate measurement result. IT8200 series has programmable performance, and can quickly recall 4 * 40 group memory data, panel function keys and display interface is clear, provide customers with simple operation program, easy and fast to complete a variety of complex tests. The series has CV, CC and CR mode, and short circuit test function, it is the most cost-effective electronic load products.
-
Product
Portable Three-Phase Meter Site Analyzer
RW-30X / RW-31X
-
RADIAN RW-30/31X Meter Site Analyzers deliver comprehensive three-phase field testing and site analysis utilizing the Radian Research RX Xytronic series reference standard as its measurement engine. The RW-30/31X provides for testing meters with integrated, precision, true three-phase voltage and current sources or using customer’s load. Choose the RW-30/31X NS (no source) model to test using customer’s load only.
-
Product
Analog Oscilloscope
FS-409
-
*OSCILIOSCOPE: 40MHz Dual Trace,Dual Trigger. 1mV Sensitivity. 10ns Resolution.*FUNCTION GENERATOR: 0.5Hz~5MHz Frequence. Sine,Square,Triangle,3 waveforms. Max output:20 Vp-p(No Load),10 Vp-p(50O Load). TTL Synchronous Output.*COUNTER: 5 Digits 0.36" Red LED Display.
-
Product
20Hz Injection Kit Monitoring System
-
Signals & Systems India Private Limited
The Display used to monitor the 20Hz and 50Hz current passing through NGT transformer. This could help to monitor the stator earth fault and could record the current every minute. The current shall be displayed in milliamps for both 20Hz and 50Hz. If an earth fault occurs in the generator star point, the 20 Hz voltage drives a current through the fault resistance. The current can be measured using clamp-on CT which would be clamped between load resistor and NGT. It gives an indication of the current values are lower or higher than the set threshold.
-
Product
150~300W DC Electronic Loads
JT631 Series
-
Nanjing Jartul Electronic Co., Ltd
JT631 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT631 series load very suitable for testing power supply when produced in large quantity. Besides, JT631 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT631 series load satisfing most of R&D requirements. Moreover, JT631 series load’s special parallel operation method can satisfy the synchronous loading requirements of multi-channels output power supply and satisfy single-channel output power supply requirement for big power.
-
Product
On Load Tap Changer Analyzer
TAP-4-PLUS
-
The Tap-4-PLUS is the newest instrument by Zensol for OLTC testing. It has 2 more analog inputs than the TAP-4. The TAP-4-PLUS with the TAP-DRM accessory can perform dynamic resistance, vibration, and motor current recordings at the same time. Doing so will allow you to easily understand the vibration impacts.
-
Product
Electric Servo Motor Type High Speed, High Load, Large Displacement Vibration Tester
-
This tester is a high-speed, high-acceleration vibration tester equipped with an electric servomotor actuator.
-
Product
On Load Tap Changer Analyzer
TAP4
-
The TAP-4 is the first instrument to use vibro-acoustic measurement to perform tests on On-Load Tap Changers (OLTC). The TAP-4 is a universal device, it adapts itself to any type of transformers: MR Reinhausen, ABB, Ferranti, Federal Pioneer and others.
-
Product
PC Controlled Bench Top Power Analyzer
PA2100
-
The PA2100 is a PC controlled bench top power analyzer, allowing several electrical power measurements to be taken simultaneously during testing - from just one set of input connections. The PA2100's power measurement ability is a must in research and development, manufacturing and required for certification and traceability of manufactured goods. In addition to power measurements, apparent power (VA), harmonics, voltage, current, power factor can all be viewed and stored with ease. The PA2100 wattmeter simply connects between the ac supply and the load, various current transformer options allow measurement with any size of current from 10mA to 10000A. Typical watt meter applications include appliance testing; microwave ovens, electric stoves, heating, air conditioning, TVs, monitors, computers, electronic lighting, fans and motor controllers. Powertek wattmeters are equipped with 4mm/banana safety terminals along with optional "breakout" boxes and clamp current probes for fast and safe measurement.
-
Product
7U VPX 4 Slot Power & Ground 10G Pass Through
101VPX704P-9X12R
-
Power for 3.3V, 5V and 12V are included, rear connectors areall fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
-
Product
Industrial Shock Absorbers
-
ACE industrial shock absorbers work hard. Their application means moving loads are evenly decelerated over the full stroke. The result: the lowest braking force and shortest braking time. The MAGNUM series from ACE is viewed as the reference standard for medium-sized damping technology.
-
Product
SparkFun Qwiic Scale
NAU7802
-
The SparkFun Qwiic Scale is a small breakout board for the NAU7802 that allows you to easily read load cells to accurately measure the weight of an object. By connecting the board to your microcontroller you will be able to read the changes in the resistance of a load cell and, with some calibration, you'll be able to get very accurate weight measurements. This can be handy for creating your own industrial scale, process control or simple presence detection. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
Vector Network Analyzer Automation Suite
ZNrun
-
For a facility manager the yardstick for optimization could be maximizing the daily production yield, while for a test-engineer it might mean being able to easily define a test setup and have it loaded on each device in the factory in seconds. A tester might be interested in seeing only the result of the measurements, after having started it by scanning a barcode, while quality managers might find it convenient to be able to download real-time yield statistics on their way to the factory. The R&S®ZNrun software suite was designed with optimization in mind and acknowledges these re-quirements by offering each party the possibility to expedite their workflows as much as possible.
