-
product
Telecomunication & Electrical Insolation- Continuity-Voltage-MOV Tester(LCD Display)
1165IN
Standard Electric Works Co., Ltd
● Measures insulation (MΩ), Continuity (Ω) , AC and DC voltage● Six insulation test voltages (DCV): 50V, 100V, 125V, 250V, 500V, 1000V● 68x34 mm (2.677x1.338 inch) large LCD● Function rotary switch design for easier operation● Intuitive operation for users● User friendly interface● Auto ACV/DCV detection● Audible voltage warning● DAR/PI indication● Backlight function● Automatic circuit discharge● Test insulation at rated voltage into a 1mA load● Auto ranging● Fuse protection● EnerSave function● MOV test function
-
product
Gear Tester
MOTOMEA gear testing capabilities offer you an accurate and reliable “Gear Testing method” where you as a user can test the gear in a dynamic way, during gear acceleration period, and in a static way, by using two loading units with very accurate speed and torque sensors at the two gear sides
-
product
PXI Power Relay Module, 16xSPST, 16 A
40-161A-001
The 40/42-161A-001 is a PXI/PXIe 16xSPST power relay module and is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock. Electro-mechanical power relays are used wich are suitable for switching loads up to 16 A at 250 VAC.
-
product
Current Transformer
Nippen Electrical Instruments Co.
DIGITAL METERS NIPPEN electronic energy meters are panel mounting type innovative energy monitoring devices ,having state of the art electronic microcontroller circuitry for reliability and accuracy. They can be used for 1Ø / 3Ø balanced and unbalanced loads.
-
product
Dual/Quad 125 MS/s VXI Arbitrary Waveform Generator
3164
The Racal Instruments™ 3164 Series is a single-wide VXIbus Module. The 3164-2 has two 14-bit Arbitrary Waveform Generator (AWG) channels that operate independently, and the 3164-4 AWG has four channels. The maximumsample rate for each channel is 125 MS/s. All waveforms can be sampled from data previously loaded into waveform memory or loaded and output on the fly.
-
product
Heavy Duty Workstations
1200 Series
The 1200 Series Vibration Isolation Workstation is designed to isolate loads up to 2800 lbs and is the obvious choice for moving loads. This workstation is a proven performer providing reliable vibration-free work environments for a wide range of industries.
-
product
10 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3430
The aTCA-3430 is a high performance 10G Fabric switch blade for AdvancedTCAR platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controllers, DPI/security network, IPTV, IP multimedia subsystems, RNC/BSC, broadband access/bearer networks, data centers, and LTE/4G network applications. The aTCA-3430 provides 10GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
product
Single 4x4 1-Pole 16 Amp PXI Power Matrix
40-552-001
The 40-552 range of 16 Amp PXI power matrix modules is available in four configurations with matrix sizes of 8x2 and 4x4 and the ability to expand the matrix size with the Y-Axis loop-thru connections: e.g. 8x4, 12x4, 16x4, etc. (with 4x4 matrices) or 16x2, 24x2, 32x2, etc. (with 8x2 matrices). This range is capable of switching up to 16 Amps and up to 300VDC/250VAC hot switching and 400VDC/250VAC cold switching. These PXI power matrix modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors, and solenoids.
-
product
Digital Display Auto Torsion Testing Machine
NJS Series
Jinan Testing Equipment IE Corporation
NJS Series Digital Display Auto Torsion tester is designed and built for torsion test on metal & non-metallic materials, as well as parts & components. NJS is loaded through the rotation of the active cartridge driven by the AC servo motor and cyclonical pinwheel reducer motor. The torque and torsion angle are measured respectively by the high-precision torque transducer and photoelectric encoder. The digital torsion testing machine is an essential instrument to inspect torsion properties of materials for mechanical laboratories of aviation industry, construction industry, scientific research department, universities and industrial enterprises.
-
product
Upsetting Testing Machine
JINAN PRCISION TESTING EQUIPMENT CO., LTD
The full-automatic rapid upsetting testing machine adopts hydraulic loading and manual control. The metal material applies pressure along the axis of the sample at room temperature or hot state to compress the sample, test the ability of the metal to withstand upsetting plastic deformation under the specified forging ratio, and display metal surface defects. It is mainly used in the upsetting test of metal materials such as iron and steel enterprises, standard parts manufacturers, and tool manufacturers to test the ability of metal to withstand upsetting plastic deformation under the specified forging ratio and display the metal surface characteristics.
-
product
Current-Voltage Measurement System
The SSIVT is an electrical current-voltage measurement system used to characterize photovoltaic cell performance. This current-voltage tester works by sampling various current versus voltage combinations of the photovoltaic cell with a variable impedence load. The performance of the photovoltaic cell is determined by measuring this output I-V relationship while it is being illuminated.
-
product
Centor Touch Star R,advanced force gauge external load cell
CNR CTR
Centor Touch Star is the most advanced force gauge currently available, it has become the benchmark tool for force measurement. Functionality, accuracy formerly reserved for expensive and complex material testing equipment are now available with Force Gauges. The functionality of material testers previously reserved for research or development applications are now available to the production floor with the introduction of the Centor Touch Force Gauge.
-
product
Transformer Testing And Monitoring
Can detect the symptoms of transformer failure by monitoring the cooling system, load tap changer, dissolved gas, bushing power factor and capacitance, partial discharge, oil levels, pressure, temperatures and more.
-
product
Meter Qualification Board
MQB
Power-up and apply load to electric watt-hour meters for functionality testing with TESCO’s multi-position MQBs. These boards assist with AMI Meter Certification process and AMI meter qualification and communication testing.
-
-
product
AC Load Bank (Resistive/Capacitive)
K-1000 Resistive/Capacitive
Kongter Test & Measurement Co., Limited
A RCD (resistive/capacitive) generator load bank is non-linear load bank. The electronic and non-linear loads simulated by capacitive load banks are typical of the Telecommunications, Computer or Uninterruptible Power Supply (UPS) Industries.
-
product
Rapid PSE And Chained Data Test Of 4-Pair And 2-Pair PSE's
PSL-3424 Quick Test for 802.at and 802.3bt PSE's
Accessible from PSA Interactive or PowerShell PSA. Scans 2 to 8 PSE ports per test cycle. Automatically determines and adapts to PSE maximum assigned class. Tests PSE’s that grant full power via PD Classification or through PoE LLDP. Validates PoE Detection Acceptance and Rejection Range. Measures PSE Port Voltage at both minimum (DC MPS) and maximum (Pclass) load conditions. Reports PSE type (AT vs BT), maximum assigned class capability, and Pclass power capacity. Assesses Disconnect Power Removal response. Assesses Overload Power Removal response. Assesses LLDP Power Protocol and Allocations (PSL-3424L).
-
product
PXI 48 x SPDT Power Relay Module
45-157-001
The 45-157 SPDT Power Relay Module consists of 48 single pole changeover relays controlled by a PXI/CompactPCI interface. It is suitable for applications were conventional reed-relay based switching modules do not have sufficient voltage rating or current carrying capacity. All 48 contacts are electrically isolated from each other and are capable of switching resistive and inductive loads up to 2000VA at 240V AC.
-
product
Heavy Duty Dynamometers
MD-250-HD
The MD-250-HD series dyno (SE/DE) was designed to be a performance dynamometer first with the added benefit of being able to test 2-wheel-drive heavy-duty vehicles such as truck, buses and commercial vehicles in addition to the standard car or light duty pick-up. The 250-HD is certified in the states of Colorado, Nevada and Utah for use in loaded-mode diesel smog testing programs because of its accuracy and reliability. No other dyno in its class offers more value or better in-house motor vehicle testing capabilities than the Mustang MD-250-HD. For starters, the MD-250-HD boasts a 1,500 horsepower measurement capacity at a top speed of 175 mph and a powerful air-cooled eddy current brake provides the MD-250-HD-SE with 900-hp worth ofloading capacity for steady state testing. Loading capacity can be increased to 1,500-hp via the optional DE model. The 250-HD can be upgraded to the 250-HD-SE-M via the addition of a 100 or 200 hp AC motor for transient testing of electric buses to measure range and regeneration or for emissions testing of IC engines. Do not be fooled by its compact size – the MD-250-HD is a serious dynamometer with serious tuning capabilities. The MD-250-HD uses a powerful eddy current power absorber, a frictionless, air-cooled braking device, to enable it to apply variable and steady state loading. A complete control and data acquisition system lets you design a wide range of tests or select from a host of pre-configured tests included with the standard system. The 250-HD’s four roller design makes setting up vehicles a snap – simply drive onto the 250-HD and let the tires settle in between the rollers. The 250-HD can be installed above-ground or below-ground, it’s your choice. The above-ground system utilizes an optional premium platform and ramp system with an above-ground restraint kit. The addition of an axle pull-down kit help keep the tires from slipping or trying to “climb out” of the rollers.
-
product
AC Load Banks
XL300-400 Series
Mosebach Manufacturing Company
The XL300-400 Series of Load Banks offer 300 kW or 400 kW in various voltages in a compact, lightweight enclosure.
-
product
QuickLink Solder-In Starter Pack for use with Dx20 Amplifier
Dx20-QL-3SI
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
product
AC Electronic Load
AC&DC Electronic Loads are design for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources and other power devices such as switches, circuit breakers, fuses and connectors.
-
product
Battery Monitoring System
BMS-3923
Kongter Test & Measurement Co., Limited
This battery monitoring system is an innovative solution to measure battery condition with communication way of Power Line Carrier (PLC). With multi-frequency measurement, users can monitor and analyze battery in all aspects: internal resistance, voltage, current, capacitance, temperature and so on.Based on our years experience for battery management system, we build very mature mathematical model that precisely predicts battery capacity. This will in another hand reduce the time that we spend on capacity measurement using a battery load bank.
-
product
Electrical Power Transducers
Manufactured for utilities since 1969, TransData Power Transducers are used for measuring AC and DC power variables in Substation, Generation, Load Control and Industrial applications where ±1ma or 4-20mA analog signal are required by the SCADA/Energy Management System. Models are available for measuring Current, AC Voltage, DC Battery Voltage, Watts, VARs, Frequency and more.
-
product
Switchboard Instrument Voltmeter
ST-96
Standard Electric Works Co., Ltd
● Test Voltage : 2kV 50-60Hz● AC Ampere Over Load Scale：200%, 300%, 500%● Composition：Glass Window, ABS resin frame and case, Bakelite base● Color：Black case and frame, white scale plate and meter body● Pointer：Stick shape in black color● Pointer Length：55mm.
-
product
ESR Analyzer
LD-LESR-A11
ESR AnalyzerLD-LESR-A11is a portable unit with Westergren analysis method and infrared sensor measuring principle. It offers measurement range of 1 to 140 mm/h with throughput up to 80 samples/h. It has maximum 20 sample loading capacity at same time and two measuring time: 30 min or 60 min. Designed with touch screen large color display, built-in printer and RS232 interface. Used for analysis of erythrocyte sedimentation rate in hospitals, clinical laboratories and research.
-
product
PCRF Load Tester
The Polaris Networks LTE PCRF Load Tester is a comprehensive test solution for evaluating the performance and the stability of LTE Policy and Charging Rules Function. The PCRF Load Tester is ideally suited for manufacturers of PCRF equipment as well as operators deploying PCRF in an LTE network. The Tester can be used for testing both the Control Plane and the User Plane under various load conditions and for measuring the capacity and various key performance indicators of EPC nodes. The Tester simulates millions of Subscriber sessions with multiple bearers per Subscriber.
-
product
Four Quadrant Power Source
PM2010
The PM2010 is a four-quadrant power source capable of supplying up to 20 V/10 Amps to a load. The maximum power that may be safely generated is 50 Watts on a continuous basis and 200 Watts peak on a pulsed mode for no more than 100 ms, and a duty cycle of less than 10%
-
product
Mechanical Testing
A range of processes including:Tensile and Compression Load TestingA test piece or component is subjected to tension (or compression) until either a proof load is achieved or failure occurs.Testing can be carried out on both metallic and some non-metallic materials.
-
product
500 N Screw Flat Grips
500 N (110 lbf) screw flat grips are for use with low-capacity AGS-X series and EZ-X series load cells and come with flat grip faces. Similar to standard screw flat grips, these grips are versatile and are used for static tensile testing a wide range of materials, including rubbers, plastics, textiles, cloth, and paper, in film form.
