Contacts
See Also: Modules, Wire, Connectors, Patchcords, Flying Leads
-
Product
Hot Sticks
HS-120
-
Standard Electric Works Co., Ltd
● Used for the extraction of fuses, isolators & fuse switch disconnections.● Can be attached to the 275 HP Proximity Detectors and contact Capacitive Detectors 21× HVD.● Universal "sunrise" head attachment to fit special tool fittings.● Head Section rated at 100kV per 300mm (5 min).● Comes complete with sunrise fitting and fuse extractor.● 3 × 1.8 meter sticks; 1 × 1.2 meter head section.● Sticks 1 × 1.2 meter head section complete with universal sunrise fitting. ● 1 × carry bag. ● Meets IEC 60855.
-
Product
Phase Indicators
-
Kyoritsu Electrical Instruments Works, Ltd.
New technology permits safe testing, without the need of direct contact between probes and live wires. The insulated crocodile clips can clip insulated cables from 2.4 to 30mm. Phase rotation is indicated by the rotary illumination of LEDs and logical audible tones. The instrument can be fixed to a metal panel via the magnet on the back side. Wide measuring range for 3 phase installations from 70V to 1000V AC. Super brightness function permits clear LED''''s indication also in sunshine. Complies with IEC 61010-1 CAT IV 600V and CAT III 1000V.
-
Product
500-Pin SEARAY Connector, Male Without Backshell, 2 Amp, 250 Port
C500RMX-4SB-5C
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This accessory is designed to allow users to directly terminate a cable via solder bucket connections to a PCB linked to a 500-Pin SEARAY connector. Pickering Interfaces recommend the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Under/Overvoltage Monitors
-
Contacts to control an external horn or light, or to signal your PLC are now available on independent accessories for any power supply. These modules can be used on power supplies with DC voltages from 5 to 125 Vdc. SPDT relay contacts switch if the power supply’s output deviates by:*1.0 volt or more (for 5 volt outputs)*2.0 volts or more (for 6 to 48 volt outputs)*3.0 volts or more (for 49 to 125 volt outputs)
-
Product
Wafer Thickness Measuring System
WT-425
-
Contact type can measure any materials within 0.2 µm (2 σ at 20℃ ±1℃). The wafer floats positions while measurement points change and it does not damage even thin wafers. Best for the process control of compound wafers and oxide wafers. (SiC, GaN, LT, Sapphire and Bonded Wafers)
-
Product
Laser Head
5517DL
Laser Head
The Keysight 5517DL is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Please contact Keysight for custom requirements.
-
Product
01 With Pins For PCB | 12 Positions | M8
01-1xxx-20/70xx-12-0
-
This variation utilizes an M8 threaded bushing for applications requiring a smaller mounting profile than the M10 standard. This 12-position switch provides the same world-renowned Elma "switching feel" and 3-micron gold-plated contacts. The M8 housing is optimized for tight front-panel layouts in test and measurement systems.
-
Product
Needle Microprobe
MT-D
-
Fast-response 29 gauge needle surface probe for locating inflammation, arteries, etc. Also for dental use. 1/4'' right angle needle length, 3/4'' needle distance from lead. 5.5'' long handle for ease of use. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Sensor within .3mm of tip. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
1553 Bus Cables, Couplers, Terminators, and Kits
Terminator
Please review 1553 Bus Accessories to the right. You can also use the Login-Download link above (login required) to access all the Hardware Manuals with specific cable and connector information. Most 1553 Cards and ENET devices have optional 1553 Jack and AUX I/O DB cable assemblies. Please see the respective product pages part numbers tab. Most ARINC products include flying-lead cable assemblies.Please use the Contact link to email/phone sales for a login as needed.
-
Product
Cable Fault Location Equipment
-
Cable fault location by electromagnetic and acoustic methods (with high-voltage pulse transmitter, which is not included into the set)Detection of insulation deterioration on cables by contact and non-contact methods
-
Product
Testing Equipment for UN38.3 & UL
-
We provide complete lab equipment solutions for UN38.3 testing and you are welcomed to visit our lab located in Richmond, CA -- please contact us for an appointment. On-site training available with extra cost.
-
Product
LXI Low Thermal EMF Matrix 1-pole 44x33
60-510-021
Matrix Switch Module
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset.
-
Product
Tool, Crimp, TriPaddle (10 amp), Thermocouple, Micro Power, Receiver and ITA , Locator Required
910101102
Crimp Tool
This crimp tool can be used to crimp 10 Amp TriPaddle contacts, Thermocouple contacts or Micro Power contacts. Locator required.
-
Product
Plugbord
3662
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.No circuit pattern edge contacts only.Unrestricted component placement over entire board surface
-
Product
Resistivity Meter of Powder Composites
RM-200
-
The resistivity meter is fully automated and does not required any adjustments. The measurement is made by using the four-point contact probe on the ring (ø60 x ø50 x 5mm) and rectangular prisms samples (6 x 6 x 60÷80mm). The measurement results are automatically saved in meter memory, what allows user to manage of data. The RM-200 contain series connection which allow the data transmission to PC.
-
Product
Topside Probing In-Circuit Test Fixtures
-
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.Today’s fifth generation Pneumatic drive supports as many as 8,000 test probes with centerline spacing to 25mil, and contacting test pads as small as 0.014″.
-
Product
LXI Low Thermal EMF Matrix 1-pole 14x33
60-510-004
Matrix Switch Module
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset. The 60-510 is designed in accordance with the LXI Standard 1.4 and is supplied in a 2U high, full rack width case with 500mm depth.
-
Product
Tachometer/Lengthmeter
-
Digital contact tachometers can be used to measure the rotational speed of quickly rotating objects or machinery. The digital tachometer features a number of different unit settings as well.
-
Product
Mini Power, Contact, Receiver, 65 Amp, 8 AWG
610116112
Power Contact (Receiver)
Primary mating contact 610115124. (May mate with other ITA contacts, as well.)Mini Power contacts carry up to 65 amperes continuous current. Maximum resistance is 1 Milliohms.
-
Product
IULTCS Rubbing Fastness Tester
TF414
-
TESTEX Testing Equipment Systems Ltd.
Rubbing Fastness Tester, to determine the color fastness to rubbing. IULTCS Rubbing fastness Tester complies with ISO11640, EN 344, SATRA PM 173, etc. You can contact us if you have any problems when you do rubbing fastness test.
-
Product
Surface Temperature Sensors
-
Campbell Scientific offers two types of surface temperature sensors: infrared temperature (non-contact) and surface contact. Infrared temperature sensors measure the surface temperature of an object or surface by sensing the infrared radiation given off by the subject. Surface contact sensors attach directly to a surface and measure the temperature via physical contact.
-
Product
Infrared Thermometer
EST-35
-
*Measures surface temperatures safely and without contact up to 500°F/ 260°C *Continuous Max Hold Feature *Built-in Laser pointer - Backlit LCD Display *Data Hold & Auto Power-Off *Carrying case included - High quality construction *Controls on front panel, not under handle *Many Automotive Applications!!
-
Product
Non Contact Temperature Sensors
-
Non Contact Type temperature measurement involves determining temperature of object surface without direct contact with the surface. Tempsens offers both single point and area inspection model devices which are infrared thermometers and infrared camera and industrial furnace monitoring camera.
-
Product
AC Contactors
-
Panasonic Industrial Devices Sales Company of America
Panasonic’s line up of AC Contactors includes the HE-N, HE PV, and HE-S Series. Differentiating features and benefits of Panasonic AC Contactors include:*High-Voltage, High-Current Control*Compact Size*High Contact Reliability*Can Be Mounted In Any Direction*RoHS Compliant*UL/C-UL Standard Certified
-
Product
Plunger Clip
BU-00201-0
-
Plunger clip • Material: Cap & Body: glass filled nylon; Spring: Stainless steel; Contact: beryllium copper; insulator to a single contact point • Length: 1.75” (44 mm)(BU-00201-*); 2.50” (63 mm)(BU-00202-*); 3.50” (88 mm)(BU-00203-*); • *Std Colors: -0 Black -2 Red • Rating: 1000 Volts, 10 Amps.
-
Product
PXI Single 55x8 Matrix 1-Pole Switching
40-538-021
Matrix Switch Module
The 40-538 ultra high density matrix module is configured as a Single 55x8 reed relay matrix with 1-pole switching. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability Sputtered Ruthenium Reed Relays, offering >10e8 operations to give maximum switching confidence with long life and stable contact resistance.
-
Product
SIL Reed Relays
Series 105
-
• SoftCenter™ construction• Highest quality instrumentation grade switches• Encapsulated in a plastic package with internal mu-metal magnetic screen• Wide range of switch confi gurations -Form A, 1 Form B, 2 Form A, 1 Form C• Two pole relay requires the same board area as the single pole type• Dry and mercury wetted switches are available with the same pin configuration and footprint.• Many benefits compared to industry standard relays. Learn more here >.• Insulation resistance greater than 10E12 Ohms (1TOhms) for dry Form A devices• 5, 12 and 24 Volt coils are standard, with or without internal diode• 100% tested for dynamic contact resistance
-
Product
iCon XL (High Power)
-
VPC's iCon XL (High Power) connector features all of the same benefits as the iCon, but with a larger bend radius and enlarged cable exit to support high power cables. Supports iCon High Power module with up to (6) 150 amp contacts. Fully wired connectors are available with flying leads. Visit the High Power page to learn more about VPC's offerings for high power.
-
Product
Protective Cover, 9025, 9025VXI & 9025TR, Receiver
310113163
Protective Cover
The Receiver Protective Cover is optional to protect your modules and contacts when the ITA is not engaged. The Protective Cover is made up of anodized aluminum.
-
Product
Short Circuit Locator for Power Cables
A910
-
The A910 is a short circuit locator designed for fault location in power cables. The instrument measures the ratio of the resistances of the two sections of failed conductor using a four-wire "Kelvin" connection, thus eliminating errors associated with contact resistances of the test leads. With the A910 you can determine if the cable has more than a short and locate the first and the last fault. The instrument locates fault with an insulation resistance up to 5 Mohms in cables that have a total resistance greater than 5mohm (approximately 90 m of 300 sqmm cable) and less than 30 kohms. The distance to fault is measured as a percentage of the total length of cable and is displayed on a large LCD display.
