Contacts
See Also: Modules, Wire, Connectors, Patchcords, Flying Leads
-
Product
Phase Sequence Indicators (Contact Type)
4156 PR
-
Standard Electric Works Co., Ltd
● The 4156 PR is used to identify the leads of a diconnected motor so that when the motor is in true phase sequence, it will run in the desired direction.
-
Product
Power Rocker Switches
-
Panasonic Industrial Devices Sales Company of America
Power Rocker Switches for safety requirements complying with Class II EN61058-1 insulation grade. 8mm minimum insulation distance and 3mm minimum contact gap. Applications include: Vehicles, Home Appliances, Outdoor Power Equipment, Agricultural, Industrial Equipment.
-
Product
Relay Modules
DN-SSR4/N
-
The DN-SSR4 includes 4 normally open, Form A, solid-state relays. The user can use the DN-SSR4 to switch high voltage load up to 240VAC and up to 4A. Four enunicator LEDs (one for each relay) light when their associated relay is activated. Each output is equipped with a varistor that shunts the surge voltage of the inductive load or electromagnetic brake to protect the relay contact point. All relay control and relay outputs are accessible through the wiring terminals.
-
Product
RFID
-
RFID technology makes reliable, radio-based identification possible without visual contact. Even in harsh ambient conditions, dozens of transponders can be read and written to simultaneously – from up to 10 m away with RAIN UHF devices. This makes RFID read/write devices the ideal solution wherever process-relevant data needs to be collected seamlessly and conveniently.
-
Product
PCI Express 16 Reed Relay Output Digital Interface
8003e
-
The 8003e PCI Express digital I/O interface provides 16 Reed relay outputs. The outputs provide high quality, long-life, dry contact switch closures suitable for low-current applications up to 10VA. Reed relays are normally open and close when energized. The board is PCI Express X1 compliant and is compatible with any PCI Express slot.
-
Product
Rolling Seal 8 Optical Connector - APC (RS8 APC)
-
The Angled Physical Contact Rolling Seal 8 Connector (RS8 APC) from Teledyne ODI is a wet-mateable optical connector with angled endfaces. The design reduces signal interference due to reflections at the connector face, supporting the next generation of subsea optical communication equipment. The Rolling Seal design provides isolation from seawater and silt when the connectors are unmated. As the seals rotate, the fibers join inside a clean, oil-filled conduit, resulting in a reliable optical throughput. The RS8 APC incorporates RS8 Mark III design features to enhance operational efficiency and reduce risks during ROV intervention.
-
Product
Tool, Inspection Depth Gauge, Mini Coax, ITA
910121157
Inspection Tool
Used to verify the depth setting of the center conductor of the ITA mini coax contacts.
-
Product
H.V. Proving Unit (DCV)
2713 PU
-
Standard Electric Works Co., Ltd
● Designed to proof: -Phasing sticks. -High voltage detectors (contact type only, not to be used with non contact proximity detectors.) -High voltage and voltage testers.● Battery operated.● Led indicates when power is “ON”.● Small and hand-held.● Quick connection with normal 4mm test leads.
-
Product
Micro Coax Modules
-
VPC modules are designed to handle harsh environments and incorporate protective contact features for both sides of mating modules.Standard modules are available in single or double width options.VPC iCon series modules offer 3 module configurations with multiple I/O options including hybrid signal modules.Modules can be loaded with any mixture of micro coax and micro power contacts.
-
Product
Low-Density PXI Switch Matrix Modules
-
Our low-density PXI switch matrix modules are a cost-effective solution for applications that require relatively small matrices in the PXI format. These low-density switch matrices can be expanded by connecting together multiple modules, however, we recommend that users look at the higher density switch matrix modules that involve less user configuration. Reed relay versions use high quality sputtered ruthenium relays that exhibit excellent contact performance under low and medium level switching conditions. For general purpose applications that also require higher power handling, the range of electro-mechanical relays provides an ideal solution.
-
Product
Inductive Proximity Sensors
-
Millions of inductive proximity sensors are currently in use in virtually all industries. They detect metal objects without contact, and are characterized by a long service life and extreme ruggedness. With the latest ASIC technology, SICK's sensors offer the ultimate in precision and reliability.
-
Product
Pro Laser Tachometer
332
-
The #332 is the ideal tool for easy and accurate measurement of RPM in almost any environment. Simply aim the laser beam at a reflective mark placed on a rotating device, push the button and the RPM reading is immediately displayed. No contact with the shaft or wheel is necessary. The laser beam is not affected by shop light and can detect RPM from longer distances of up to 6 feet away. The #332 can measure up to 99,999 RPM in 1 RPM increments. It can be used to measure RPM on coil-on-plug and diesel engines, where conventional inductive tachometers can not be used. Other uses include generators, compressors, industrial engines, fans, gears and more. Zippered case, reflective tape, instructions & 9V battery included.
-
Product
Single Molecule Microscopy
-
Nano-scale precision motion and stability are cornerstones of research grade microscopes for single molecule imaging. Mad City Labs has developed modular microscopes that ease integration of optical components and assist users with developing and adapting instrumentation for their own application requirements. Contact our single molecule microscopy application development team to discuss the right products for your application.
-
Product
Modulator Driver
-
A compact bias control board designed to maintain the linear operating point of optical intensity modulators. Featuring a compact miniature design for OEM integration, the BCB-4 allows for a stable Q+, Q-, Min and Max operation over long periods of time. With a USB 2.0 DC power and monitor interface standard, the BCB-4 unit is the ideal choice for industrial and OEM applications when paired with any of Optilab’s wide variety of optical modulators. Please contact us at +1(480)719-1502 or email sales@oequest.com for more info.
-
Product
GPIB Digital Interfaces
-
All of ICS's GPIB Digital Interfaces are user configurable and let you transfer data as bits, bytes or as strings of bytes. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard and are HP-IB compatible.
-
Product
Scanning Kelvin Probe
-
Our large range of Scanning Kelvin Probes gives the user full access to 2D and 3D work function plots of samples ranging in size from 50 mm to 350 mm. With work function resolution of 1 - 3 meV, and the spatial resolution of the Probe tip diameter (0.05 mm with the SKP5050 model), the Scanning Kelvin Probe gives reliable, repeatable measurements for work function, contact potential difference and Volta potential.
-
Product
Wristat Tester
WT25
-
The WT25 WRISTAT Tester is designed to test the integrity of our WRISTAT in a fast, efficient and simple manner. All of the elements of the WRISTAT - continuity of the strap, integrity of the protective resistor, and satisfactory strap to skin contact are easily confirmed by pressing the top cover of the WT25. The operator (wearer) is tested for a resistance to ground of greater than 750K ohms and less than 10M (switchable to 100M ohms).
-
Product
Wind Transmitters
-
Comptus wind speed and direction transmitters convert the sensor signals into electrical outputs suitable for connection to displays, computers, dataloggers, wireless transmitters, or other controls. Output options include: 0-1 mA, 0-1 V, 0--5 V or 4-20 mA. Power options include: 24 VAC, 120VAC, 230VAC, 12-24 VDC. Comptus transmitters come standard in a track mount for installation in existing enclosures. They are also available in NEMA rated enclosures. Please contact us for enclosure options.
-
Product
PXI 40Amp 14Volt 4xSPST Automotive Relay
40-180-101
Relay
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC. The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
Non Contact Thickness Measurement Systems
-
Non contact thickness measurement is becoming more complicated with each passing year.From medical devices to food packaging, we understand the needs from an array of industries to successfully design non contact thickness measurement systems to meet your needs:
-
Product
500-Pin SEARAY Connector, Male Without Backshell, 1 Amp, 500 Port
C500RMX-4SB-0A
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This accessory is designed to allow users to directly terminate a cable via solder bucket connections to a PCB linked to a 500-Pin SEARAY connector. Pickering Interfaces recommend the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Coax, Contact, ITA, 20/26 GHz, 3.5MM, w/ SMA Adapter, 90 Series Modules only
610102134
Contact Adapter (ITA)
Coax, Contact, ITA, 20/26 GHz, 3.5MM, with SMA Adapter (90 Series modules only)
-
Product
Hydrostatic Head Tester
-
TESTEX Testing Equipment Systems Ltd.
Hydrostatic Head Tester is used for measures the resistance of a fabric to the penetration of water under hydrostatic pressure. Hydrostatic Head Tester complies with AATCC 127, EN 20811, ISO 1420A, etc. Please contact us for Hydrostatic head test procedure.
-
Product
NON CONDUCT DIGITAL THERMOMETER
IBL-MT5
-
International Biological Laboratories
This Digital Non Contact type Infra Red Thermometer with laser sensor uses temperature sensor of Thermopile 6 - 14 mm and measures temperature from -50 to 550 Degree C and also in Fahrenheit scale.
-
Product
Temperature Measuring Instruments
-
– Contact and ambient temperature measurement– Infrared temperature measurement
-
Product
Laser Markers / 2D Code Readers
-
Panasonic Industrial Devices Sales Company of America
Panasonic Laser Markers are ideal for the high speed, non-contact, permanent labeling of metals, plastics, resins, glass and natural materials such as paper, wood or leather. Panasonic's Laser Markers make no contact with the target object and have no moving parts or consumables - a strong advantage over methods like stamping or engraving.
-
Product
Receiver, I2 Micro ICon, 120/12 Position Hybrid, Loaded With Twin Female Contacts (610 138 200)
310130104
Receiver
The i2 Micro iCon receiver is a one piece connector capable of holding up to 120 Signal QuadraPaddle contacts and 12 Micro Coax or Micro Power. QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. This i2 receiver is pre-loaded with twin female contacts, QuadraPaddle Part # 610 138 200. Accessories such as keying pin kits, protective covers, and strain relief are available.
-
Product
Test Package
-
Shenzhen Bonad Instrument Co., Ltd.
We can provide a variety of different specifications of freezing load test packages, including AHAMHRF-1 2007/ SASO 2664-2007 Sawdust freezing test package, AS1731.4-2003 Australian frozen Load Test Package, AS72-2005 North American Commercial Refrigeration Load Simulation Test Package, IEC 62552 Test Package for Freezing Load Testing in Refrigerators. In addition, we can also provide customization according to test requirements. For more information, please contact us, BONAD will provide you with professional technical advice and high-quality testing equipment.
-
Product
PCB Connectors
HPH Series
-
Smiths Interconnect's HPH series is a high density interconnect available up to 303 contacts with multiple hardware choices and backpotting option
-
Product
Thermocouple, Module, ITA, 90 Series, 64 Position
510108124
ITA Module
Primary mating module 510104133. (May mate with other Receiver modules, as well.)*Please note: VPC receiver modules must be separated into two pieces in order to extract contacts. For detailed instructions please consult the user manual/procedure sheet for this module before extracting contacts.
