Contacts
See Also: Modules, Wire, Connectors, Patchcords, Flying Leads
-
product
PXI 128x2 Matrix Module, 1-Pole, 2A, 60W
40-584-001
Our model 40-584, along with the following models40-584, 40-585, 40-586A and 40-587Aare high-density single pole PXI matrices each supporting 256 crosspoints. All models use gold-plated contact electromechanical relays. The PXI matrix modules are designed for switching medium voltage and power signals. The user signal connection is via a robust 78, 50 or 37 pin D-Type or 160 pin DIN 41612 connector that is fully supported by the wide range of our cable and connector accessories.
-
product
Open Top BGA Sockets
Ironwood has the most comprehensive collection of open top BGA and QFN sockets that can be used for qualification application, silicon FIB testing, system development, thermal characterization, burn-in application, etc. IC socket can be defined as an electromechanical device, which provides removable interface between IC package and system circuit board with minimal effect on signal integrity. Typical packages include BGA, LGA, QFN, QFP, WLCSP, etc. Open top allows access to the top side of IC. Below is an example BGA socket that uses low cost elastomer contact technology.
-
product
Split Type Ultrasonic Level Gauge
HR9100D
HighReach Measuring & Controlling System Co.,Ltd
1. Stable and reliable / We select high-quality modules and key components from the power supply part to select high-stability and reliable devices, which can directly initiate imported instruments. 2, patented technology / one ring patented sound wave intelligent technology software can Intelligent outgoing analysis without any debugging and other special steps, this technology has the function of dynamic thinking, dynamic analysis 3, high precision / sound wave intelligence owned by our company The patented technology greatly improves the accuracy of the ultrasonic level gauge, the Liquid level accuracy reaches ±0.2%, can resist various interference wavesThe instrument is a non-contact instrument, not Direct contact with liquid, so the failure rate is low. The instrument provides a variety of installation methods, users can use this . The Instrument Manual Calibrate to 5. The Protection of The Level of Multiple Protection / IP67 & Instrument Reaches; INPUT and Output Lines All have have Lightning Protection and Short Circuit Protection.
-
product
Flying Prober Test System
QTOUCH1404C
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built high resolution Vision Camera for easy monitoring of probe needle contact. The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision.
-
product
Power Systems
In mission-critical field applications deployed in harsh environments, such as a dry desert or an arid mountainous terrain, it is difficult to secure necessary grounding contact.
-
product
PXI Single 32x8 Matrix, 2 Pole Switching
40-531-022
Model 40-531 very high density matrix modules are configured as a 32x8, while the 40-532 modules are configured as a Dual 16x8. Both modules are available in a choice of reed relay formats: 1-pole, 2-pole and 1-Pole screened. The screened version is suitable for switching coaxial signals up to 50MHz. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability Sputtered Ruthenium Reed Relays, offering 109 operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules. For example, seven PXI modules will form a 224x8 Matrix, a total of 1792 crosspoints in a 7-slot PXI Chassis.
-
product
ContactLAB Tester
The ContactLAB test platform provides fully configurable reader signal emulation for validation of ISO 7816 contact smart cards and Single Wire Protocol (SWP) USIM for NFC enabled mobile handsets.
-
product
Single 12x12 1-Pole High-Density PXI Matrix Module
40-520-102
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
product
Standard- 27.20 (771.00) - 64.00 (1814.00) Godzilla High Current Probe
HC375F-4
Current Rating (Amps): 100Average Probe Resistance (mOhm): 25Test Center (mil): For more details, please contact us.Test Center (mm): For more details, please contact us.Full Travel (mil): 360Full Travel (mm): 9.14Recommended Travel (mil): 250Recommended Travel (mm): 6.35Overall Length (mil): 3,110Overall Length (mm): 78.99
-
product
Replacement Protective Cover, G10, ITA
410112685
The vinyl ITA Protective cover is durable and shock resistant to protect your contacts and modules when the ITA is not in use.
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196C
The 16196C surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Contacting Extensometers
The contacting extensometers are designed for accurate strain and extension measurement of a material up to a maximum sample thickness of 25 mm.
-
product
Analytical Techniques
Anderson Materials Evaluation, Inc.
Our numerous analytical techniques, we tackle a wide range of materials challenges and commonly combines several analytical techniques to fully address complex and multi-dimensional materials issues. Our materials analysis laboratory provides XPS surface analysis, thermal analysis (TGA, DSC, TMA), FTIR infrared spectroscopy, UV-Vis spectrophotometry and reflectivity measurements, gas chromatography – mass spectroscopy (GC-MS), SEM/EDX, optical microscopy, mechanical testing, electrochemistry and corrosion analyses, residual gas mass spectroscopy, contact angle measurements, surface contamination measurements, adhesive bonding failure analysis, facility testing for silicone contamination, mechanical testing, metallography and fractography, density and porosity measurements, volatile organic component testing, friction, and other analytical capabilities. We continue to upgrade and expand our arsenal of analytical techniques and custom analytical methods to support our customers’ needs.
-
product
CMT - Tester
VPC G12 interface - interchangeable fixturesQuick exchange of test applicationMinimum of equipment in the fixture - fixture only as contacting interfaceManual fixtures ATXFixture identification - automatic test program loadingConnection to external meas. instrumentsControled by SCADUS / LabViewSelftest of internal cards and connected instrumentsCentral test program, configuration and datalog files location possibility (server)Uninterruptible power supply for PC
-
product
Optical Contact POF Ext Ø 1mm For VPC RCV Mini Power 510104123
AN396
Optical contact probe for sensing LEDs.
-
product
IBM PC-XT, Vectorbord Plugbord
4613-3
VECTOR Electronics and Technology, Inc.
62 contacts (31 each side) on 0.100" centers. Pad per hole. Voltage and ground buses around board perimeter. I/O mounting area for 37-pin D-sub and ribbon cable connectors. Mounting bracket and hardware kit included (P/N HD36B).
-
-
product
VTAC, Insert, Receiver/ITA, SIM, Vertical Header, 8 Pos
610151107
The VTAC vertical header insert contains 8 VTAC high speed contacts and is designed to mount directly to a PCB. It can be configured as a backplane connector and daughterboard connector. Also sold as a set with 610151108.
-
product
Pass-Through Oven
UF TS
The Memmert heating oven with fully insulated stainless steel door on both sides saves time during loading and reduces the risk of contamination, specially when handling sensitive load between grey and clean rooms. On this page, you can find all the essential technical data on our pass-through oven. Our customer relations team will be pleased to help if you want further information. If you should require a customised special solution, please contact our technical specialists at
-
product
Amplifiers - Solid State
PMI offers a full line of RF and Microwave Amplifiers that range from 250 kHz up to 50.0 GHz. Many options are available. If you do not see exactly what you require on this website, please contact sales@pmi-rf.com because we offer amplifiers designed and built to your specifications at catalog prices.
-
product
68-Pin SCSI Micro-D Male Ribbon
40-961-068-M
This connector is designed to allow users to directly terminate with IDC connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
product
OCT Imaging
Optical Coherence Tomography (OCT) imaging on the system, subsystem, and component level. Our drive for innovation is shaping our entire rapidly expanding product line. Complete SD-OCT systems are available that are out-of-the-box ready for biological, industrial, and research applications. In addition to our standard OCT systems, Thorlabs offers Doppler OCT extensions for specialized applications. For customers building or modifying their own system, a line of components that have been tested for use in OCT applications is available. In addition to the growing portfolio of standard OCT systems that we offer, Thorlabs is dedicated to providing OCT solutions to meet specific applications. Please contact us to discuss how our OCT technologies can be applied to meet your unique requirements.
-
product
Linear Array
Linear array sensors consist of a linear array of integrating photosensing pixels which measure incident light over a user-defined exposure time and generate a voltage or digital output which represents the light exposure at each pixel. The sensors are available in a variety of lengths and pixel resolutions. The analog output may be directly interfaced to an ADC for digital processing or for comparing black/white thresholds. Applications include contact image sensing, optical character recognition, edge detection, and object measurement in products such as copiers, document scanners and spectroscopy.
-
product
ITA, IDock Series, D1, 1 Module
410131102
ITA, iDock Series, D1, 1 Module The D1 ITA can engage up to 160 signal contacts. Select any of our iCon series modules to configure your D1's I/O.
-
product
Controllers
BKM93KIO
Clockwise and/or counter-clockwise rotation of the wand is programmable allowing an optimum adaptation to the machine.The scanning intensity is adjustable in 8 steps. Even rotating drills with small diameters can be checked.The scanning results are display as "OK" or "KO" and signalled by LEDs on the front side of the device.The PROFIBUS is a standard Sub-D 9 pin connection; the USB connection is a USB-mini plug / type B and meets the 2.0 specification.Three digital inputs serve to activate the functions "Teach-in" to learn the position to be scanned, "Start" to initialize the scanning process and "Configurable" for receiving a stop command.Two digital outputs provide the signals for the message "OK" or "KO".The relay contacts are configurable as N/C or N/O connections. They can be set as momentary (valid with start or timed) or latching.Convenient configuration software for programming and setting of tool data is available at no cost.
-
product
S-100 Bus, Vectorbord Plugbord
8801-1
VECTOR Electronics and Technology, Inc.
100 Gold plated edge contacts (50 each side) on 0.125"(3.175mm) centers. No circuit pattern edge contacts only. Unrestricted component placement over entire board surface
-
product
Slip Rings Separates
Separates are typically rings and insulation material assembled on an axis along with separate contact brushes. They are usually designed with flying leads. Once integrated, they provide electrical contact between stationary and rotating parts of a slip ring assembly. They use bearings from the host system and provide a more compact and economical solution than self-contained Slip Rings. The coupling of these items requires technical skills from the OEM and is suitable for applications that have tight mechanical requirements.
-
product
S2 Ultra High Sensitivity Sensors
ULP-S2 UHS
Universal LightProbe S2 Ultra-High Sensitivity Sensors are designed for the test of very dim LEDs, as low as 0.01 mcd minimum, and including very low light-level LED-illuminated action-indicator switches, controls and status indicators for night/dark viewing in automobile interiors. Recommend the use of wide-aperture stainless- steel encased Fiber- optic Probes with contacting tips.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. long.Typical response times: <190mSFiber-Optic Probes: Wide-Aperture Fiber-Optic Probe recommendedDesigned for the test of very dim LEDs, as low as 0.01 mcd minimum
-
product
20 Channel Actuator/GP Switch Module for 34970A/34972A
34903A
The Keysight 34903A is a general-purpose switch module for the 34970A/34972A Data Acquisition/Switch Unit. It has 20 independent single-pole, double-throw (SPDT) relays and is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Combine it with matrix and multiplexer modules to build custom switch systems. Its 300 V, 1 A contacts can handle up to 50 W, enough for many power line switching applications.
-
product
Strain sensors
SG-01
The Strain Gage SG-01 is the fibre optic equivalent of an electrical strain gage. The Strain Gage SG-01 can be mounted directly on the surface of a structure by means of an adhesive. In this way, the fibre sensor makes direct contact with the surface and therefore measures directly the strain at the surface.
