Cards
See Also: Extender Cards, Probe Cards, POST Cards, Test Cards, Boards, Modules
-
Product
Isolated Serial Communication Card
PCI-ICM-1S
-
The PCI-ICM-1S is a single port asynchronous optically isolated serial communication card that can be installed in any 3.3V or 5V PCI slot computer. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
Product
Carrier Card
SPR518
-
The SPR518 provides a smart upgrade path to affordably replace the existing SPR418A PCI Express (PCIe®) carrier for XMC modules. The new card provides for unimpeded data transfers within traditional PCs, at the full rate supported by the mezzanine card.
-
Product
256 Digital Input/Output Channels
CP387
-
The C387 is a single-width, 6U, CompactPCI module with up to 256 digital input/output channels. The C387 base board supports 128 channels of TTL I/O. Four mezzanine card sites can be populated with other forms of digital I/O including isolated input, isolated output, relay output, AC switch output or differential I/O. The mezzanine card concept allows multiple digital I/O types to be configured within a single module to match the application requirements.
-
Product
PCI Single Slot Intelligent Interface Card
IIB-3910-PCI
-
The IIB-3910-PCI is a single slot intelligent interface card providing complete STANAG 3838 and STANAG 3910 test, simulation and bus analysis capability for the PCI Bus.
-
Product
8" Cable
CONW1553-1
-
Transitions from a card end connector (with IRIG) on the QVME-1553 or QVXI-1553X into two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends, and four 8" cables with BNC cable jacks for I/O triggers and IRIG Rec/Gen.
-
Product
Fanless Embedded System With LGA1151 9th/8th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, 4-CH PoE And MXM 3.1 Type A
eBOX671-521-FL
-
The eBOX671-521-FL is a GPU computing embedded system that comes with 4-CH PoE and MXM 3.1 Type A slot for applications in machine vision, edge computing, traffic vision, deep learning, and artificial intelligence of things. The outstanding eBOX671-521-FL with enhanced GPU computing performance is powered by the 9th/8th gen Intel® Core™ i7/i5/i3 processor with up to six-core, Intel® Pentium® processor, or Intel® Celeron® processor and comes with Intel® Q370 or optional Intel® C246 chipset. The fanless embedded GPU-based system is equipped with dual DDR4 ECC/non-ECC SO-DIMM slots for up to 64GB of system memory. The embedded vision system has an optional MXM type A slot for NVIDIA GTX1030 and GTX1050 graphics modules to enhance the performance of the visual display. Furthermore, this Intel® Coffee Lake-based embedded box PC is specially designed with four Gigabit 802.3at (PoE, Power-over-Ethernet) compliant Ethernet ports with a total power budget of 60W, six USB 3.1 ports and two Gigabit LANs to connect different devices or sensors. It comes in great expansion possibilities, including one internal MXM 3.1 type A connector, two full-size PCI Express Mini Card slots and two SIM slots. For storage, it has two swappable SATA HDD drive bays with a height of up to 9.5 mm and one mSATA for RAID 0 and 1 feature. Besides, we have designed a flexible I/O window slot for incorporating application-oriented I/O functions to meet the requirements of various cases. This embedded vision computer can be mounted using wall or DIN-rail mounting for versatile use in various environments.
-
Product
PXI Single 2 Channel Optic Mux FC/PC
40-855-112
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
General Purpose Switches
General Purpose Switch
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
-
Product
Robust RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, COM, SPI, I2C, 2 LANs And DIO (2-in/1-out)
IFB125
-
The IFB125 is powered by the low-power Freescale i.MX6UL processor in the ARM® Cortex™-A7 micro architecture. It supports extended operating temperature ranging from -40°C to 70°C, and can withstand vibration up to 5G. Its flexible wide voltage range 9V - 48V DC power input with a lockable terminal block type connector also enhances its reliability in harsh environments. To meet most of Industrial IoT needs, the IFB125 supports multiple communication interfaces for maximum flexibility, including LAN, serial, USB, and digital I/O ports. The Industrial IoT gateway has 256MB onboard memory that features data transfer rates of DDR3-1600, as well as 4GB eMMC flash memory onboard for storage. This embedded IoT gateway platform is equipped with one PCI Express Mini Card slot and one SIM card slot. Additionally, it supports DB9 connectors with both SPI and I2C function as communication protocols to suit for specific applications
-
Product
48 Channel Threshold Comparator FPGA PXI Card
GX3748
cPCI Card
The GX3748 is a user configurable, FPGA-based, 3U PXI card which features 48 voltage comparator channels. The daughter board interfaces to the GX3700 FPGA baseboard which employs the Altera Stratix III FPGA. Each input channel can accept input voltage signals from 0 to 50 volts, with programmable threshold levels. Three of the 48 channels are supported by the board's timestamp event feature.
-
Product
CMOS Image Sensor
CIS
-
CMOS Image Sensors (CIS) allow multiple camera functions in mobile devices, automobiles and security systems. Nidec SV Probe provides both standard and advanced versions of our CIS cards employing a wide variety of materials ensuring a durable cost-saving solution that can meet the fine pitch and multi-dut challenges of these devices. Other features and benefits include: • Proprietary AC™ Alloy Probes • Reduced Damage Under the Pad • High Frequency Capability • Better Alignment StabilityOur advanced CIS card, the Multiplexer™, is offered specifically for high density and high parallel applications. The Multiplexer™ is built with cantilever needles held into place on one side and shorter AC™ probes on the other which leads to a more stable electrical characterization over other CIS probe card options.Contact your Nidec SV Probe Representative so we can help you find the right CIS product for your testing needs.
-
Product
FPGA PXI Card With 80 Channel LVDS Buffer Module
GX3611
FPGA PXI Card
The GX3611 is a 3U PXI FPGA card with 80, LVDS channels and is comprised of the GX3500 PXI FPGA card and the GX3511 expansion card.
-
Product
IP Module with 2 CAN Ports
IP-CAN
-
The IP Module driver can be instantiated multiple times to control multiple cards by the same CPU. IP-CAN when coupled with the Dynamic Driver "knows" what slot it is in and which carrier it is installed into. The slot and carrier information is required when using multiple cards in a PCI/PCIe system with dynamic address assignment.
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 65.5k Ohm
40-294-033
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 1.81kΩ
50-298-122
Programmable Resistor Module
The 50-298-122 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 1.81kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Micro-D (Male)
Micro-D (Male)
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 100-pin Micro-D connector.
-
Product
13-slot ATX-supported PICMG1.3 Bus Passive Backplane
FAB114
-
The FAB114 has a PICMG 1.3 CPU card slot, one PCI Express x16 slot, three PCI Express x1 slots and a total of eight 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Through one PCIe x16 link, this PICMG 1.3 backplane maximize the performance of high-end PCI Express graphics and video cards. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB114 is perfect fit for AXIOMTEK's SHB100 and SHB110. AXIOMTEK also offers versatile 4U industrial chassis specially design for the FAB114, such as the AX61400, AX6156 series and AX61491.
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 32.7k Ohm - SPST
40-294-132
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Economical Desktop/Wall-Mount Chassis With Front I/O Interfaces For ATX Industrial Motherboard
RK-500MB-L
Chassis
- Front I/O Interface and seven PCIe expansion slots for add-on cards- Supports industrial ATX motherboard- One 5.25'' external and two 3.5'' internal- Flex ATX power supply- 12 cm two ball bearing cooling fan ( 103 CFM)
-
Product
Rack Mount Kestrel Chassis M/E/F-Series 37-slot
0228
-
This chassis has a 38-slot 21MX backplane of which 37 are available to the user. It also includes power supply and cooling fans. A firewire Chassis Interface Card (CIC) must be purchased to provide back-plane signals from the Kestrel to the chassis.
-
Product
VME Load Card
-
WIENER VME load boards are designed to test VME crate power supplies and fan trays by drawing power from the VME backplane and dissipating it as heat. A series of switches on the module front panel allows for easy adjustment of the current draw for each voltage channel.
-
Product
High Voltage 50 Pin D-Type Cables - Connector To Connector For Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a highvoltage 50-pin D-type connector.
-
Product
Powered VME430 Crates
9U VME430 6021
-
WIENER VME 6021 crate series is the newest generation of generation CERN VME430 compliant VME crates for large size 9Ux400mm cards. Designed for applications in nuclear and high energy physics data acquisition, beam line control and test instrumentation it combines superior mechanical quality with lowest noise power supply technology.
-
Product
PXI Single 32x8 Matrix Card, 1 Pole
40-530-021
Matrix Switch Module
Typical applications for this high-density reed relay matrix include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability Sputtered Ruthenium Reed Relays, offering 109 operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules. For example, seven PXI modules will form a 224x8 Matrix, a total of 1792 crosspoints in a 7-slot PXI Chassis.
-
Product
COM Express Type 10 Mini Application Board With LVDS, VGA, Dual LAN And Audio
CEB94018
-
*84 x 55 mini size form factor*2 GbE LAN*SATA and mSATA*LVDS and VGA*6 USB 2.0*2 PCI Express Mini Card slots
-
Product
High Voltage 50 Pin D-Type Cables - Connector to Unterminated for Pickering Products
-
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a high voltage 50-pin D-type connector.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 3Ω To 52.4kΩ
50-298-133
Programmable Resistor Module
The 50-298-133 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 52.4kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
VPX/VME64x Hybrid, Type 39 E-Frame, Test Platform (Tall)
39E08ADXC8Y3VG3X
-
The Type 39 E-Frame, test platform supports development from legacy VME64X to VPX. With a rugged aluminum construction, the versatile 39 E-Frame is 12U to hold 6U cards. The full size (84HP) width holds 17 cards (3 on .8 inch and 14 on 1 inch pitch).
-
Product
External Measuring Systems
LAN, USB
-
An alternative for measuring cards integrated in a PC are external data acquisition systems from BMCM. In this case, sampled data are transmitted to the PC via the USB interface or the LAN network - perfect for mobile applications!
-
Product
PMC Carrier Card
APC-PMC
-
This board provides an easy and low cost solution that enables use of a PMC mezzanine I/O module in a standard PCI computer system. The carrier card acts simply as an adapter to route PCI bus signals to and from the PMC module through the PCI card slot edge connector.
