Fuel Injector
-
Product
Comprehensive Fuel Injection Pressure Test Kit
38000
-
A complete, master fuel injection pressure tester for cars and trucks.Tests gasoline fuel injection pressure systems on virtual all domestic and imported cars and trucks.For multi-port, throttle body and C.I.S. K-Jetronic fuel Injection Systems.Supplied with complete instructions in a durable, plastic molded storage case.
-
Product
On-Board Fuel Consumption Detector
MF-3200
-
- High accuracy within ±0.2 % of reading- Compact size and light weight- A fuel cooling function is provided as standard.- Simultaneous measurement of temperature and pressure together with the flow rate
-
Product
Portable Fuel Dilution Meter
FDM 6000
-
The FDM 6000 is a portable, battery operated fuel dilution meter that determines the concentration of fuel dilution present in an oil sample within a matter of minutes. The FDM 6000 uses a unique patent pending fang design to pierce the cap of a disposable sample vial and draws in the headspace from the vial. The headspace flows over a SAW (Surface Acoustic Wave) sensor which reacts specifically to the presence of fuel vapor with a detection range of 0 – 15%. It can detect diesel, gasoline or jet fuel in engine oil. It conforms to ASTM D8004 - "Standard Test Method for Fuel Dilution of In-Service Lubricants Using Surface Acoustic Wave Sensing"
-
Product
SparkFun LiPo Fuel Gauge
-
LiPo batteries are a great way to power your projects. They're small, lightweight, and pack a pretty good punch for their size. Unfortunately, even the best batteries eventually run low on power and when they do it's often unexpected (and at the worst time). Don't be caught by surprise next time your board suddenly powers-down! The SparkFun LiPo Fuel Gauge connects your battery to your project and uses a sophisticated algorithm to detect relative state of charge and direct A/D measurement of battery voltage. In other words, it tells your microcontroller how much 'fuel' is left in the tank. The LiPo Fuel Gauge communicates with your project over I2C and an alert pin also tells you when the charge has dropped below a certain percentage.
-
Product
Common Rail Injector Tester
ICR-4 Tester
-
ICR-4 tester is used to control electromagnetic and piezoelectric injectors used in the common rail injection systems. It is possible to control up to four injectors of a type at a time. The signal generated by the tester which controls the injectors, corresponds to the signal which appears in the car engine controller.
-
Product
Solid Oxide and Molten Carbonate Fuel Cell Test Stations
-
Greenlight''s SOFC test systems include options for integrated reformers, de-sox, gas mixing, water saturation, pre-heating, furnace, heat recovery and water balance. These SOFC test rigs can be configured to operate on gaseous or liquid fuels, with operating temperatures up to 1000C. Pressure control is optional and furnaces can be tailored for either planar or tubular cell configurations. For single cell or button cell testing, Greenlight offers the X20 table-top SOFC test bench, including furnace and optional fixtures.
-
Product
Fuel Cell Test Software
-
Exceptional functionality with a user-friendly graphical interface- Enhanced with our proprietary automation language, Emerald Software - Comprehensively manages the full range of FCATS fuel cell test system parameters- Simple user-friendly interface permits even novices to begin testing in minutes
-
Product
COMPRESSION, VACUUM AND FUEL PUMP TESTER COMBO SET
MCVK
-
*Tests compression on all domestic and import cars and trucks with gasoline engines*Compression tester kit includes: 2-1/2" gauge with dual inch/metric readings: 0-300 psi and 0 to 21 kg/cm2, 14mm/18mm solid short adapter, 14mm/18mm long flexible adapter and 14mm long reach adapter*Checks vacuum and fuel pump pressure and locates air leaks in fuel lines, vacuum operated chokes and emission control systems on all domestic and import cars and trucks with gasoline engines
-
Product
Hydrogen Fuel Cell
-
Honeywell Aerospace Technologies
Honeywell has a decades-long history of innovation in power generation for all kinds of aerospace and defense applications, which was further strengthened by the 2020 acquisition of Ballard Unmanned Systems, a global leader in fuel cell technologies for unmanned aerial vehicles (UAVs).
-
Product
FC(Fuel Cell) Impedance Measurement System
KFM2150 System
-
The KFM2150 system is a fuel cell impedance measurement system configured with an FC impedance meter KFM2150 and an electronic load PLZ-4W series. Combination of KFM2150 and PLZ-4WA series (0V input type) supports impedance measurement for single cell of fuel cell.In addition to impedance measurement with AC impedance method, KFM2150 system provides IR measurement with current interrupt method.Application software enables test for each characteristic of fuel cell such as I-V characteristics, Constant Current characteristics, Current Interrupt method and Cole-Cole plot by the AC impedance method. Moreover, each test can be performed in a specified order.
-
Product
2GE PoE, SFP Injector
EKI-2742FPI
-
Supports multi-rate for SFP slot, IEEE 802.3af/at compliant, Power input 48 VDC, supply 30W per port, Provides slim size and DIN-rail/Wall mount with IP31 metal mechanism.
-
Product
Fuel Injection Pressure Tester with 2 Gages & Quick Couplers in Storage Case
53980
-
Tests gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Quick couplers provide for fast and easy hook-up.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Tests all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Tests all Ford vehicles with Multi-port fuel injection systems.
-
Product
Injector Tester
7620A
-
Peaceful Thriving Enterprise Co Ltd
By connecting with the 12V battery, the tester generates four different output signal pulses for user to check the condition of the injector. By using the tester, user can check if the injector is clogged, leaking, or blasting. By selecting the continuous pulse, user can also use this test to help clean the injector.
-
Product
Fuel Injection Pressure Tester Bleed-Off Kit
37400
-
Adds a bleed-off feature to our Cat. Nos. 33770, 33800, 33865, 33900, 33950, 33980, 53770, 53900, 53950, 53980, (This feature is included with Cat. Nos. 36200, 36250, 38000, 53800, 53865, 56200, 56250 & 58000 ).
-
Product
PoE Injector
-
Our PoE Injectors support Power Over Ethernet powered devices in industrial environments. They deliver both data and power over a single standard Ethernet cable to a PoE powered device designed to receive both data and power through its RJ-45 port connector.
-
Product
Electronic Fuel Quantity Indicator
-
Proportional to the amount of fuel in the tank, thereby visibly indicating remaining fuel quantity to the pilot.
-
Product
Fuel Injection Pressure Tester with 2 Gages in Case
33980
-
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with multi-port and some throttle body injection (TBI). Test all Chrysler cars with multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Test all Ford vehicles with multi-port fuel injection systems.
-
Product
Electronic Fuel Injection & Ignition Spark Tester Kit
36310
-
Quickly diagnose "no start" and engine miss conditions in the electrical fuel injection and spark plug circuits. Analyze rough running engines. Contains Cat. No. 36300, Noid Light Set to test electronic fuel injection signals and the Cat. No. 23900, In-Line Ignition Spark Checker to trouble shoot the ignition system (Shows a duplicate view of the ignition spark). Supplied with Noid Lights to check Bosch PFI, Ford TBI, Geo TBI, GM PFI, GM SCPI and GM TBI.
-
Product
Fuel Hose Assembly Tester - Basic, USAF
9901-10FHT
-
The basic fuel hose assembly tester is utilized by those users who do not require the complete 9201A test system which includes all test adapters and components required by U.S. Air Force PD 89MMI638. The 9901-10FHT however includes the identical test pump, manifold and controls and with larger valves, ports and fittings for increased fluid flow, is designed for the identical mission of testing fuel hose assemblies. Maximum pressure is 1000 psi allowing better control resolution at lower test pressures.
-
Product
fuel Center Products
-
Secure PCI compliant and easy to install networking solutions for all the data connections in and around your fuel center.
-
Product
High-Precision Fuel Flow Measurement System
-
It enables to keep the temperature fluctuation of the circulation flow path in the system within ±0.2 °C (for 1 minute), which achieves stable fuel flow rate measurement.
-
Product
On-vehicle Ultrasonic Fuel Flow Meter
RealFlow
-
The RealFlow ultrasonic sensor from HORIBA represents a breakthrough in fuel flow measurement technology, for both the compactness in size and its high level of accuracy.The RealFlow has been designed for the ultra low-volume fuel flow conditions found in today’s high-efficiency road car engines, making it an ideal tool for R&D as well as emissions testing to the RDE and WLTP standards - especially with its ability for true engine bay installation due to being so compact in size - a real game changer in the Automotive industry!
-
Product
Fuel Cell Hardware
-
The TP series cells are designed primarily for researchers who are providing their own MEAs, but they can be provided with MEAs as well. They can be offered as stand-alone cells, or as integrated equipment with our turn-key testing stations.
-
Product
Battery Fuel Gauge
-
Global Digital Instruments, LLC
SenDEC Battery Fuel Gauges are designed to accurately monitor the charge capacity of lead acid batteries. SenDEC fuel gauges can be used to monitor DC powered equipment such as fork lifts, golf carts, floor care equipment, and any other battery powered equipment. Three battery discharge profiles are standard, plus custom profiles, and a lockout option.
-
Product
Fuel Flow Info
-
Custom range and dial markings are available. Call UMA representative for details!
-
Product
Injector Tester
7620
-
Peaceful Thriving Enterprise Co Ltd
By connecting with the 12V vehicle battery, the tester generates four different output signal pulses for user to check the condition of the injector. By using the tester, user can check if the injector is clogged, leaking or blasting.
-
Product
Fuel Injection Tester
FIT13APB
-
This basic fuel injection tester includes large and small Schrader adapters, M6-1.00 O-ring adapter, and tee manifoldIncludes everything necessary to test the following systems: American Motors; Bosch AFC, MPC European and Japanese (except CIS- use our FIT447); Chrysler Corporation; Ford Motor Company; GM (except TBI- use our FIT446)
-
Product
DURAMAX PVC/EVAP FUEL RAIL PRESSURE RELEASE TOOL
MST144
-
*Works on 2011 and later Duramax LML engines*Saves time by eliminating the need to remove EGR cooler and fuel rail*Quickly removes the Duramax fuel pressure release valve which otherwise would take up to 8+ hours to service
-
Product
SpectrOil M/F-W Fuel Analyzer
SpectrOil M
-
The SpectrOil M/F-W is a compact, rugged and easy to use fuel analysis spectrometer. It is designed specifically for the analysis of ash-forming contaminants in fuel such as sodium, potassium and vanadium that cause corrosion or deposits at turbine operating temperatures. It measures trace quantities of dissolved or suspended contaminant particles in a fuel sample using the time-tested and reliable rotating disc electrode (RDE) technique.
-
Product
Interface Cards / PoE Injector
-
Gigabit Ethernet with PoE allows for single cable camera solutions, simplifying installation and maintenance. For those who will be externally powering the camera we offer a single port Gigabit Ethernet card and a PoE injector unit.
