-
product
IoT Ethernet I/O Modules
ADAM-6000/6200
Supporting Modbus & IoT protocols, Ethernet remote data acquisition modules offer analog, RTD, thermocouple, digital, relay and counter I/O.
-
-
product
Reconfigurable FPGA w/ AD/DA & Digital I/O PCIe Mini Card
TMPE627
The TMPE627 is a standard full PCI Express Mini Card, providing a user programmable Xilinx Artix-7 7A50T FPGA. The TMPE627 provides 14 ESD-protected 5 V-tolerant TTL lines. All I/O lines are individually programmable as input or output. TTL I/O lines can be set to high, low, or tristate. Each TTL I/O line has a pull-resistor to a common programmable pull-up voltage that can be set so +3.3 V, +5 V and GND.
-
product
16 Differential I/O Multi-Mode Transceiver Channels
DF1
Function module DF1 multi-mode transceivers with 16 programmable I/O channels. Differential transceivers increase resistance to noise by creating two complementary signals. These complementary signals produced on balanced lines double noise immunity by creating lower power requirements due to lower supply voltages.
-
product
USB-6343, 32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device
781439-01
32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device - The USB‑6343 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6343 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
PCI-6513, 64-Channel, ±30 VDC, Sink Outputs, Bank-Isolated Digital I/O Device
778970-01
The PCI-6513 is an industrial digital output interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6513 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
SH37F-37M-1 37-Pin Female to Male Shielded I/O Cable, 1 m
778621-01
SH37F-37M-1 37-Pin Female to Male Shielded I/O Cable, 1 m
-
product
6U VME I/O & Comm Board
64C3
NAI’s 64C3 is a 6U VME multifunction I/O and communication board with six function module slots that can be configured with a variety of I/O and communication functions. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.By eliminating the need for multiple, specialized, single-function boards, this unique design increases packaging density, saves enclosure slots, and reduces power consumption. The 64C3, a low-power/high-performance board, is ideally suited for rugged defense, industrial, and commercial applications.
-
product
Vision System With LGA1151 Socket 7th/6th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® H110, 4 PoE, 4 USB 3.0, And Real-time Vision I/O
IPS960-511-PoE
Featuring a multi-core CPU, IP40-rated rugged design, camera communication interfaces, real-time vision-specific I/O with microsecond-scale and LED lighting control, the IPS960-511-PoE provides an all-in-one solution that addresses the needs across various machine vision platforms and automatic inspection cases. The IPS960-511-PoE is powered by the LGA1151 socket the 7th & 6th generation Intel® Core™ (codename: Kaby Lake/Skylake) and Celeron® processors (up to 65W) with the Intel® H110 chipset. The intelligent vision system comes with dual DDR4-2133/2400 un-buffered SO-DIMM sockets for up to 32GB of system memory as well as supports rich camera interfaces for connecting industrial cameras, including four IEEE802.3at PoE LAN ports and four USB 3.0 ports. Its vision I/O integrates a full range of isolated I/O interfaces and real-time controls essential to machine vision applications, including trigger input, LED lighting controller, camera trigger, as well as an encoder input for conveyor tracking. The IPS960-511-PoE also supports lighting dimming control to identify object characteristics for different inspection. Two easy-swappable 2.5" HDDs are available for extensive storage needs.
-
product
SCB-100A Noise Rejecting, Shielded I/O Connector Block
785024-01
100-Pin Female SCSI to 100-Pin Female Screw Terminal, DIN Rail, Wall, Pane Terminal. Block The SCB-100A is a shielded I/O connector block for interfacing I/O signals to NI data acquisition devices with 100-pin connectors. Combined with shielded cables, the SCB-100A provides rugged and protected signal connectivity. It has a mechanical enclosure that features a magnetic removable lid and pinout diagrams. It also includes pane, wall, and DIN Rail mount options.
-
product
24 TTL Channels, Enhanced, Programmable I/O
TL2
Function module TL2 provides 24 channels of TTL/CMOS transceiver functionality as either inputs or outputs. The transistor-transistor logic (TTL) employs transmitters with multiple emitters in gates having more than one input. TTL offers high switching speed and relative immunity to noisy systems. CMOS sensors provide image sensing technology by converting light waves into signals that are small bursts of current. These waves can be light or other electromagnetic radiation.
-
product
REM-11100, 2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O
784748-01
2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O - The REM‑11100 is a voltage input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11100 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. This module features 2‑, 3‑, and 4‑wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling.
-
product
Industrial CANopen And CANopen FD Module For Digital I/O Applications
PCAN-MicroMod FD DR CANopen Digital 1
The PCAN-MicroMod FD DR CANopen Digital 1 is an I/O module for use in CANopen and CANopen FD networks. The modern CANopen FD® standard makes it possible to cope with the constantly increasing need for data transmission from sensors, machines and complex production systems. The module has a CAN FD interface as well as 8 digital inputs and 8 digital outputs. With the DIN rail housing and the support of the extended temperature range, the module is suitable for use in an industrial environment.
-
product
PMAC Input/Output (IO) Modules
PMAC Input/ output (I/O) modules offer a wide range of analog or digital IO including AC, DC, TTL and analog.
-
product
16-bit, 100KHz, 16SE/8DIFF A/D Inputs; 8 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
APCI-3120-16-8
*Optical isolation 500 V*16 SE or 8 diff. inputs*Data transfer rate: 100 kHz*16-bit resolution*8 analog output channels*Data transfer rate:30 kHz*14-bit resolution
-
product
Configurable 3U CPCI Multifunction I/O Boards
Optimized to deliver unusually high-function density, high resolution / accuracy and low power consumption for rugged defense, commercial aerospace, and industrial applications, NAI’s intelligent 3U CompactPCI cards can often operate as standalone systems, eliminating the need for a Single Board Computer (SBC), operating system and associated software royalty costs.
-
product
LVDS Digital I/O with Virtex-6 FPGA - 6U VPX
Model 58610
- 32 or 64 bits of LVDS digital I/O- One or two LVDS clocks- One or two LVDS data valid- One or two LVDS data suspend- Supports LXT and SXT Virtex-6 FPGAS- One or two DMA controllers move data to and from system memory- Up to 2 or 4 GB of DDR3- PCI Express (Gen. 1 & 2) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O to the carrier board- Ruggedized and conduction-cooled versions available
-
product
Robust DIN-rail Fanless Embedded System With 7th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor And Dual Modular I/O Expansion Design
ICO500-518
The ICO500-518 featuring flexible I/O expansion, sufficient storage and network capability is well-suited for transportation, public utility, smart building, solar energy, as well as factory automation fields. By bundling Axiomtek’s intelligent AMS software solution for device monitoring and remote management, the ICO500-518 is able to implement environment signal monitoring, edge analytics and remote device management in the IIoT world. It has also passed the EN 50121-4 certified for railway applications. The rugged high computing edge gateway has scalable CPU options with the 7th gen Intel® Core™ i7/i5/i3 (codename: Kaby Lake-U) or Celeron® processors and supports one DDR4-2133 SO-DIMM slot for up to 16GB of system memory. The ICO500-518 features basic benefits whether low latency or cost efficiency; moreover, offering much more other advantages for IIoT applications. It not only supports multiple OT communication protocols that can significantly reduce the effort required to collect data from different field devices, but also provide local intelligence to allow operators respond faster to events that happen at the remote site and minimizes latency between edge devices and the cloud server. Also, with TPM 2.0, this IIoT edge gateway provides tailored levels of security depending on the application needs. Axiomtek’s ICO500-518 has two optional plug-in I/O module slots and four different types of I/O modules to meet different customization requirements. An integrator can choose from four available I/O modules including an 8-port GbE LAN module; 8-port isolated RS-232/422/485 module; 4-port isolated RS-232/422/485 with one isolated DIO (8-in/8-out) module; 8-port isolated CANbus 2.0A/B module to customize the ICO500-518 to fit its specific project requirements. Additionally, the ICO500-518 offers flexible communication options - two full-size PCI Express Mini Card slots and one external SIM card slot for 4G/3G, GPS, LoRaWAN, Wi-Fi and Bluetooth connections. Furthermore, it supports swappable 2.5-inch SATA drive and external CFastTM card to provide sufficient storage capability. For withstanding harsh operating conditions, this IP40-rated embedded box PC offers an extended operating temperature range of -40°C to 70°C, a wide range DC input of 12V to 48V with OVP, UVP, OCP, RPP power protection, and up to 3G vibration endurance.
-
product
PCIe-7851, Virtex-5 LX30 FPGA, 750 kS/s Multifunction Reconfigurable I/O Device
781102-01
Virtex-5 LX30 FPGA, 750 kS/s Multifunction Reconfigurable I/O Device - The PCIe‑7851 features a user-programmable FPGA for high performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7851 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
I/O Input/Output Board
VME-4514A
The VME-4514A Analog I/O (AIO) Board provides 16 high-quality analog output channels which can be programmed with on-board jumpers to operate in a variety of voltage ranges. Each output can source or sink 10 mA at ±10 V. For off-line testing, the analog outputs can be disconnected from the I/O connector.
-
product
Avionics I/O Computers
With so many built-in capabilities, these highly-flexible avionics I/O computers are the ideal fit for a wide range of applications.
-
product
I/O Board With Two COM, Four USB 3.0, One Gigabit LAN, HDMI And Audio For PICO312, PICO313, PICO511, PICO512
AX93A01
*Specification: 1 x RS-232/422/485, 1 x RS-232, 4 x USB 3.0, 1 x HDMI, 1 x Gigabit LAN, 1 x Audio (MIC-in/Line-out), 1 x Power-on, 1 x Reset, 2 x LED*Dimensions: 118 x 40 mm*Compliant products: PICO312, PICO313, PICO511, PICO512
-
product
ATCA I/O Rear Transition Module (RTM)
ART002
The ART002 is an I/O expansion ATCA Rear Transition Module (ARTM) that provides GbE, 10 GbE, PCIe, USB and Management I/O for the front blade.
-
product
I/O Input Board
VME-3123A
16-Bit High-Throughput Analog Input Board, 16 Channels with Simultaneous Sample-and-Hold Inputs
-
product
PCI Digital I/O Cards
Sealevel PCI digital I/O cards are available with optically isolated inputs and Reed relay outputs. For high-voltage requirements, TTL versions provide convenient connections to industry-standard solid-state relay racks. Sealevel low profile PCI digital I/O boards meet the requirement for the MD1 low profile specification and feature Universal Bus (3.3V and 5V) for compatibility with both new and legacy computer systems.
-
product
PXI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module
778965-01
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6514 is an industrial digital I/O interface with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
3U cPCI I/O & Comm Board
75C3
NAI’s 75C3 is a 3U cPCI multifunction I/O and communication board with three independent function module slots. Two of the slots can be configured with a variety of I/O and communication functions; the third, with either a combination module featuring four multiplexed A/D channels and 28 Discrete I/O programmable channels, or with a reference supply. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
-
product
PCIe-7842, Virtex-5 LX50 FPGA, 200 kS/s Multifunction Reconfigurable I/O Device
781101-01
Virtex-5 LX50 FPGA, 200 kS/s Multifunction Reconfigurable I/O Device - The PCIe‑7842 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7842 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
Wireless I/O & Sensors
Advantech provides wireless I/O and sensor modules to shorten the gap between the field sites and the cloud.
