-
Product
8-Ch, 16-Bit Isolated Analog Input EtherCAT Remote I/O Module
AMAX-4817
Analog Input Module
Suitable for EtherCAT networks8-ch, 16-bit analog input channels with 2,500 VDC isolation±275 V high common-mode voltage rangeQuick removable European type connectorSupports EtherCAT Distributed Clock (DC) mode and SyncManager modeTwo rotating switches for up to 256 slave IDs
-
Product
Test Slave For The LIN Bus With Various I/Os
PLIN slave
-
The PLIN slave is an evaluation board with an interface for a LIN 2.0 bus. The device also offers comprehensive I/O functionality, which is accessible via operating and display elements.
-
Product
LVDS I/O Module
LVDS-MOD3
-
Curtiss-Wright Defense Solutions
The LVDS-MOD3 is a front panel mezzanine module designed to provide LVDS I/O functionality to Curtiss-Wright's FPGA-based processing PMC modules. This LVDS I/O module provides 32 differential pairs to the front panel. The LVDS-MOD3 LVDS I/O module is aimed at embedded application development.
-
Product
PXI 32 Channel I/O, High and Low Side Driver
40-413-003
Digital I/O Module
The 40-413 range is available in three configurations, a high side only, a low side only and a combined high and low side (shown here) –each capable of driving 2A loads. Each output is fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments.
-
Product
Dual PoE-PSE I/O Board/Box
AX93A21
-
*2 PoE-PSE ports comply with IEEE802.3af standard via an internal cable or network cable connected to LAN ports on SBC to power an external PoE device*With an external 12 VDC-in, the 2 PoE-PSE ports are capable of following IEEE802.3at standard
-
Product
4-Ch, 16-Bit, 200 KS/s Isolated Analog Output USB 3.0 I/O Module
USB-5820
USB Interface
USB 3.0 SuperSpeedDaisy chainable by built-in USB hub4 x 16-bit analog output channels with 2,500 V DC isolationMultiple voltage and current output rangesRemovable European-type connectorSupported operating systems: Windows 10/11
-
Product
2Counter/2DO Modbus RS-485 Remote I/O
ADAM-4080
-
2ch counter/2ch digital outputProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system2500VRMS isolation protectionCounter frequency up to 50kHZ
-
Product
6-Ch Voltage Analog Input EtherCAT Slice IO Module
AMAX-5017V
EtherCAT Slice IO Module
Channels : 6 (Differential)Input Type : V,mVVoltage Range : ±150 mV, ±500 mV, ±1V, ±5 V, ±10 VInput Impedance : >10M ΩResolution : 16-bit with ±0.1% FSR accuracySample Rate : 100 sample/s (per channel)
-
Product
Digital I/O Boards
-
Cable Transfer speeds up to 400 mb/per second Large FPGA provides for flexable cable interface
-
Product
16-Ch Sink-Type Digital Output EtherCAT Slice IO Module
AMAX-5057
Digital I/O Module
Channels:16 (Sink Type)Voltage Rating:10~30VDCRated Current Output:0.3A per channel atsignal "1"Leakage Current:25 μA per channel atsignal "0"Output Delay:From logic level 0 to 1:10μs;From logic level 1 to 0: 100μs
-
Product
96 Channel I/O and 64 Channel I/P VME Module
DP-VME-3132
-
The DP-VME-3132 provides 96 channel RS422 differential digital I/Os and 64 channel RS422 differential isolated inputs on the front end and rear side. On the rear side, it is interfaced with the VME 64x backplane.
-
Product
PCI Multi-function I/O Module
APC730
-
APC730 I/O boards provide a variety of I/O functions on a single card. These high-density boards perform both high-speed and high-resolution A/D and D/A conversion and also handle digital I/O plus counter/timer functions.
-
Product
12DI/6DO IoT Modbus/SNMP/MQTT Ethernet Remote I/O
ADAM-6050
Ethernet I/O Module
12ch digital input(counter)/6ch digital output(pulse output)Protocols:MQTT(TLS),SNMP,Modbus TCP,RESTful API,ASCIIGCL to perform basic logic control rulesPeer-to-Peer function to map I/O statusCloud access: Data update to AzureBuilt-in web serverWatchdog timer to recover the system
-
Product
Analog Output Module For Remote I/O
Analog Output Module
The Analog Output Module for Remote I/O features a 2-wire spring terminal connection, selectable output ranges (0 V to 10 V, ±10 V, 0 V to 5 V, ±5 V, 0 mA to 20 mA, 4 mA to 20 mA, and ±20 mA) output ranges, and short circuit proof outputs. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Analog Output Module for Remote I/O from a real‐time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
-
Product
PXIe-6381, 16 AI (18-Bit, 625 KS/s), 2 AO (2.86 MS/s), 24 DIO, PXI Multifunction I/O Module
790689-01
Multifunction I/O
The PXIe-6381 offers analog I/O, digital I/O, and four 32-bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe-6381 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
General Purpose I/O Modules
HY-TTC 36X
-
HY-TTC 36X is a CANopen-based, cost effective, modular and user-friendly solution for extending the number of I/Os in mobile applications. This controller is best suited for different kinds of control tasks in a vehicle and acts as slave unit in a CAN-based network architecture.
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24 V.
APCI-1500
-
PCI interface to the 32-bit data busConnector compatible to PA 1500Connector and software compatible to CPCI-150016 isolated input channels, 24 V, including 14 interruptible3 software-programmable counters/ timers16 isolated output channels, 10 to 36 V, output current 500 mATimer-programmable watchdog for the reset of the outputs to ??Diagnostic report through status register in case of short-circuit, overtemperature, voltage drop or watchdogInterrupt triggered through watchdog, timer, errorOne ground line for all inputs and one ground line for all outputs
-
Product
I/O Board With Two COM, Four USB 2.0 And Audio For PICO840, PICO841, PICO842, PICO843
AX93283
-
*Specifications: 1 x RS-232/422/485, 1 x RS-232, 4 x USB 2.0, 1 x Audio (MIC-in/Line-out), 1 x power-on, 1 x Reset, 2 x LED*Dimensions: 118 x 29 mm*Compliant products: PICO840, PICO841, PICO843
-
Product
PCI Digital IO Board
-
*Bus Interface: PCI Bus*Counter/Timer: 16 Channels*Counter Size: 32 bit*Max. Source Frequency: 80MHz*Compatibility: 5 V TTL/CMOS*Discrete Inputs: 24 Channels*Discrete Outputs: 24 Channels*Pulse Generation: 12 Channels*Bi directional I/O's: 8 Channels*Oscillator stability: 50 ppm*Op-to isolation for I/O's*DMA buffered operation*16-bit data bus 32 bit Address bus for External Memory Interface*The Pulse Width and PRI of the pulses can be varied*The pulse generation frequency from 10Hz to 40MHz (25ns to 100msec)*The no. of pulses controlled from 1 to 255 pulses*All the pulse input and the output signals and Bi-directional write signals driven through Pin Driver*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
I/O Board With Two COM, Four USB 3.0, VGA And Audio For PICO880, PICO500, PICO300
AX93275
-
*Specifications: 1 x RS-232/422/485, 1 x RS-232, 4 x USB 3.0, 1 x VGA, 1 x Audio (MIC-in/Line-out), 1 x Power On, 1 x Reset, 2 x LED*Dimensions: 118 x 40 mm*Compliant products: PICO880, PICO500, PICO300
-
Product
6U VME I/O & Comm Board
64C3
-
NAI’s 64C3 is a 6U VME multifunction I/O and communication board with six function module slots that can be configured with a variety of I/O and communication functions. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.By eliminating the need for multiple, specialized, single-function boards, this unique design increases packaging density, saves enclosure slots, and reduces power consumption. The 64C3, a low-power/high-performance board, is ideally suited for rugged defense, industrial, and commercial applications.
-
Product
4AI/4DO Modbus Ethernet I/O
WISE-4010LAN
Ethernet I/O Module
Supported protocols: Modbus/TCP, TCP/IP, UDP, DHCP, HTTP, MQTTSupports RESTful web API in JSON formatSupports local logging with RTC time stampSupports mobile device web configuration in HTML5Supports 10~30 VDC power with reverse protectio
-
Product
Remote I/O
-
ADAM remote I/O are categorized into 5 families: IoT/OPC UA Ethernet I/O, Modular I/O system, RS-485 I/O and Serial/USB Converters/Repeaters.
-
Product
High Density I/O Module
ADAM-500 Series
-
Remote I/O modules for multi-channel thermocouple data acquisition with Modbus RTU/TCP support, ideal for precise temperature monitoring.
-
Product
Multifunction Analog I/O Card
LPCI-AIO16A
-
Model LPCI-AIO16A provides 500k samples/second, with 16-bit resolution, for the board’s 16 single-ended or 8 differential analog input channels. Also included are two 12-bit analog outputs, 16 digital I/O lines and an 8254 with three 16-bit counter/timers. The board meets the MD2 Low Profile PCI Bus Specification and can be installed in any 3.3V or 5V PCI or PCI-X slot.
-
Product
16-Ch Isolated Digital Input And 16-Ch Isolated Digital Output EtherCAT Remote I/O Module
AMAX-4830
Digital Input Module
Suitable for EtherCAT networks16-ch digital input and 16-ch digital output with 2,500 VDC isolationWide input voltage range (10 ~ 30 VDC)Wide output voltage range (5 ~ 40 VDC) and high output current (350 mA/ch)Quick removable European type connectorLED indicators for I/O statusSupports EtherCAT Distributed Clock (DC) mode and SyncManager modeTwo Rotary switches for up to 256 slave IDs
-
Product
Reconfigurable FPGA w/ AD/DA & Digital I/O PCIe Mini Card
TMPE627
-
The TMPE627 is a standard full PCI Express Mini Card, providing a user programmable Xilinx Artix-7 7A50T FPGA. The TMPE627 provides 14 ESD-protected 5 V-tolerant TTL lines. All I/O lines are individually programmable as input or output. TTL I/O lines can be set to high, low, or tristate. Each TTL I/O line has a pull-resistor to a common programmable pull-up voltage that can be set so +3.3 V, +5 V and GND.
-
Product
100 MHz 32-CH High-Speed Digital I/O Card
PCIe-7360
Digital I/O Module
ADLINK's PCIe-7360 is a high-speed digital I/O board with 32-CH bi-directional parallel I/O lines. Data rate up to 400 MB/s is available through the x4 PCI Express® interface. Clock rate can support up to 100 MHz internal clock or 200 MHz external clock, ideally suiting applications of high-speed and large-scale digital data acquisition or exchange, such as digital image capture, video playback and IC testing.
-
Product
I/O Board With Two COM, Four USB 3.0 And Audio For PICO880, PICO500, PICO300
AX93299
-
*Specification: 1 x RS-232/422/485, 1 x RS-232, 1 x Audio (Mic-in/Line-in/Line-out), 4 x USB 3.0*Dimension: 118 x 40 mm*Compliant Product: PICO880, PICO500, PICO300
-
Product
4Relay/4DI IoT Modbus/SNMP/MQTT 2-Ports Ethernet Remote I/O
ADAM-6266
Ethernet I/O Module
4ch relay/4ch digital input(counter)Protocols:MQTT(TLS),SNMP,Modbus TCP,RESTful,ASCIIGCL to perform basic logic control rulesCloud access: Data update to AzureAuto-bypass function to ensure daisy-chain data transmissionPeer-to-Peer function to map I/O statusBuilt-in web serverWatchdog timer to recover the system
