Force Gauges
measure push and pull.
-
Product
CORROSION GAUGE
MX-1
-
The MX-1 will hold a single velocity, making it the perfect choice applications where only one material is being tested day after day. With the preset velocity in the gauge, you simply turn it on and go to work. The tool's backlit display is easy to read, even in dim light conditions, and the unit operates for up to 200 hours on a single set of AA batteries. The MX-1 comes complete, ready to use, and is protected by Dakota Ultrasonics 5 year limited warranty.
-
Product
3-Component Quartz Force Rings And Links
-
Three-component dynamic force sensors are offered in both ICP® and charge output configurations for dynamic and quasi-static force measurement applications. Each utilizes an array of precision aligned, quartz sensing crystals. Measurements along the z-axis are proportional to applied compression, tension and impact forces. Measurements along the x and y axes are proportional to shear forces that are imposed upon preloaded crystals by the test fixture.
-
Product
Vacuum Pressure Gauge
EEPV511
-
Test vacuum accessories and emission control devices such as EGR valves canister purge systems, air switching and divert valves, vacuum delay and check valves, heater and A/C controls and cruise control systemsMulticolor gauge face with scales of inch, Hg, psi, negative kPa and positive kPa
-
Product
High Force Type Spring Probes
-
Total length of spring probes for high force is longer than standard type and is more optimized to use for testing PCB. We have 1mm to 2.54mm pitch and you can choose not only tip type but also spring force for each pitch. This makes it possible for you to choose spring probe suits the best for your use.
-
Product
High Performance Fluorescent X-ray (XRF) Coating Thickness Gauge
FT150 Series
-
Hitachi High-Technologies Corp.
The FT150 is a high-end fluorescent X-ray coating thickness gauge equipped with the polycapillary X-ray focusing optics and Vortex silicon drift detector. The improved X-ray detection efficiency enables high throughput and high precision measurement. Furthermore, new design to secure wide space around sample position gives exellent operability.
-
Product
Acquisition Of Strain Gauges, Isolated, 18-bit
APCI-3300-8
-
18-bit resolution, unipolar, 16-bit accuracy 8 differential inputs for strain gauges Voltage range 0 to + 2.5 V 8 independant voltage sources for the connected pressure sensors Output voltage for the voltage sources 5 V, 40 mA Gain and offset calibration Calculation of the pressure value through software Programmable gain 16-bit accuracy with sample rates of 20, 40, 80 or 160 Hz 4 digital input channels, 24 V and 3 digital output channels, Open Collector, isolated
-
Product
Wall Measurement Thickness Gauge Wall Thickness Test Instrument
HS160
-
Shenzhen Chuangxin Instruments Co., Ltd.
HS160 Wall measurement thickness gauge, wall thickness measuring equipment apply to measure the thickness of all kinds of material, through which the ultrasonic wave can propagate at a constant speed and can get reflection from the back. This instrument can be used for a variety of plate and all kinds of machining parts for accurate measurement. Another important function of this gauge is to monitor all kinds of pipelines and pressure vessels used in the production equipment, monitoring their degree of corroded thinning during the using process. It's widely used in petroleum, chemical industry, metallurgy, shipbuilding, aviation, aerospace and other fields.
-
Product
Ultrasonic Thickness Gauge
45MG
-
The 45MG is an advanced ultrasonic thickness gauge packed with standard measurement features and software options. This unique instrument is compatible with the complete range of Olympus dual element and single element thickness gauge transducers, making this innovative instrument an all-in-one solution for virtually every thickness gauge application.
-
Product
Load Cells & Force Transducers
-
BLH and Nobel Weighing Systems offer a wide variety of load cells and force transducers, ranging from the unique KIS load cell and weigh module to the VPG transducers range of products. Our many years of experience, our state-of-the-art instruments, and the exceptionally broad range of components that go into our systems allow us to deliver high-quality solutions tailored to your needs.
-
Product
Pressure Gauges
-
Digital and analog pressure gauges in absolute, barometric, gauge, differential, sealed gauge, and vacuum pressures in a variety of pressure units including bar and psi up to 25,000 psi.
-
Product
A-/B-Scan Thickness Gauge For NDT
SONOWALL® 70
-
SONOWALL 70 is the first thickness gauge in the market with intelligent probe identification. The extended probe management allows probe-specific information such as DAC-curves, delay lines, and serial numbers to be saved directly in the ultrasonic probe. In addition to various thickness applications, the device can be upgraded to a full-function flaw detector.
-
Product
Linear Gauge Sensors
GS Series
-
All the GS series Digital Linear Gauges are upgraded. The GS-1700/1800 series is a compact and cost effective basic type. The GS-6700/6800 series is a vibration resistant type which provides better performance of vibration resistance 1.5 times in strength compared to the basic type. The GS-4700/4800 pursuits heavy-duty performance required in production site. Long stroke type the GS-5050/5100 series has wide measurement range (stroke) at 50 mm or 100 mm. Using ball bearing mechanisms in these all models greatly increases bearing life.
-
Product
High Power Temperature Forcing System
MaxTC G4
-
NEW G4– MaxTC is our premium Temperature Forcing System product, specifically designed for industry needs as a result of customer´s feedback from the Flex-TC. Its powerful cooling force (90W @ -40°C), rapid transition rates (75°C /min) and remote control capabilities will provide solutions to all semiconductor testing needs. MaxTC is compact, ultra quiet (55 d BA) and fits into any laboratory. A premium product at amazing value.
-
-
Product
Strain Gauge Measuring Instruments
-
It is a Strain Gage Indicator and also function as a Strain Gage Transducer Indicator.As a Strain Gage Indicator, it can support 10 types of bridges and dummies. While if used as a Strain Gage Transducer Indicator, there are 24 bits A/D converts to make the measurement.
-
Product
Gauge Type T Thermocouple Wire
W-TW-44
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Quartz Charge Force Rings
-
Ring-style sensor configurations measure dynamic compression. Tension measurements are also possible if the unit has been installed with proper pre-load.
-
Product
Digital Indicator for Strain Gauge Sensors
AD-4530
-
Low cost digital indicator for various applications. Suitable for measurement of load, pressure, torque, tension and more at an affordable price.Digital Zero (DZ) stores zero data at any measurement point. This function can also be used to tare weight. Measurement can simply be restarted when it was interrupted by a loss of power.Power on zero function adjusts to zero when the power is turned on.Digital filter provides stable measurement results.Digital span calibration. Easy calibration just by inputting the rated output of a sensor. No need to use a mass.
-
Product
Contactless Wafer Geometry Gauge
MX 20x series
-
The E+H geometry gauges are based on two heavy plates mounted parallel to each other. Embedded in the plate are a set of capacitive distance sensors. The wafer will be moved manual or automatically between the plates and measured without any movement.
-
Product
Gauge Type T Thermocouple Wire
W-TW-24
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
-
Product
Digital Linear Gauge
GS-7710A/7710NA
-
GS-7000 series are pen-figured type of linear gauge sensors at φ8mm, which are mostly suitable for multi-point measurement.It can save the space at the measurement area and its structure is conforming to the IP67 protection class which has enough durability against harsh environment.
-
Product
Imaging Gauge Software Test System
-
The IMAGING GAUGETM quality analysis system was developed by APPLIED IMAGE to address the growing need to standardize the evaluation of camera image quality. The system includes a Test Chart manufactured using our ACCUedge® technology, along with unique Image Analysis Software, used together to analyze the quality of the imaging system, and then provide a summary report on the various image quality metrics. Our goal is to provide a simple to use, unique image analysis system, that can be utilized by R&D, scientists, system integrators, technicians and field operators to evaluate the camera quality or imaging system.
-
Product
Tool, Inspection Depth Gauge, Mini Coax, Receiver
910121156
Inspection Tool
Used to verify the depth setting of the center conductor of receiver mini coax contacts.
-
Product
Contactless Wafer Gauge for Resistivity, Thickness
MX 60x
-
The MX60x series measure Resistivity or Sheet Resistance of silicon and other materials.
-
Product
Ultrasonic Thickness Gauge
72DL PLUS
-
The Olympus 72DL PLUS™ ultrasonic thickness gauge delivers precision thickness measurements at high speed in a portable, easy-to-use device. With fast scanning, advanced algorithms, and our lowest-ever minimum thickness capability, you can confidently measure the thickness of very thin layers in the most challenging applications.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type C, Ø1.50mm, 305gf
K100-C150305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style C, Tip Diameter Ø1.50mm, Spring force 305gf, Steel with Gold Plating.
-
Product
Pressure / Force Sensors
-
Panasonic Industrial Devices Sales Company of America
Panasonic offers high precision Pressure Sensors for industrial, medical, clean room and other gauge equipment uses. Some include a built-in amplifier and compensating circuit in a compact, low and high pressure Sensor with high accuracy and reliability.
-
Product
Electronic Tensile Strength Tester Pull Force Test Chamber Applicable Industri
-
Shenzhen Chuangxin Instruments Co., Ltd.
This machine can test various materials (both finished and semi-finished products ) of tensile strength ,compressive strength and elongation ,can do stripping ,tear strength ,flexural ,compression test and etc. It can connect up to the computer and display or printout the test times , test value , max. value , etc . Also it can make various report forms according to the requirements .
-
Product
Strain Gauge and RTD via Ethernet
2612
-
Simultaneous measurement of four strain gauges or RTDs6 or 4-wire measurement with 200 nV resolution at a 6 Hz rateAuto-calibration cycle measures excitation at remote strain gaugeCompatible with Linux and WindowsUse our design assistant to configure a system and calculate pricing
