Force Gauges
measure push and pull.
-
Product
Strain Gauge and RTD via Ethernet
2612
-
Simultaneous measurement of four strain gauges or RTDs6 or 4-wire measurement with 200 nV resolution at a 6 Hz rateAuto-calibration cycle measures excitation at remote strain gaugeCompatible with Linux and WindowsUse our design assistant to configure a system and calculate pricing
-
Product
Analog Surface Profile Gauge
NOVOTEST LIMIT
-
Mechanical depth gauge is designed to comply with ASTM D 4417-B, SANS 5772, US Navy NSI 009-32, US Navy PPI 63101-000 for (depending on configuration): measures the peak-to-valley height of a blast cleaned surface; measurement the depth of focal corrosion; measures depth of narrow holes and grooves.
-
Product
Digital Coating Thickness Gauges
-
The Elcometer range of digital coating thickness gauges has been specifically designed to provide highly accurate, reliable and repeatable coating thickness measurements on almost any substrate, whether ferrous or non-ferrous. Dry Film Thickness can be measured on either magnetic steel surfaces or non-magnetic metal surfaces such as stainless steel or aluminium using a digital coating thickness gauge. The principle of electromagnetic induction is used for non-magnetic coatings on magnetic substrates such as steel. The eddy current principle is used for non-conductive coatings on non-ferrous metals substrates.
-
Product
Linear Strain Gauges
-
Linear Pattern Strain Gages are the most straightforward geometry of strain gauge, designed to indicate strain in only a single direction.
-
Product
Forced Air Cooled RF Coaxial Loads
86700 Series
-
The 86700 Series Forced Air Cooled RF Coaxial Loads are capable of dissipating up to 75 kW of CW RF power from DC Hz to 240 MHz with a VSWR of 1.15:1 or less. With this low reflection coefficient the loads are very useful for tuning transmitters.
-
-
Product
Sensor Products: Weld Force Gage
90061
-
Model 90061 is a self-contained, portable measurement system which allows auditing of the pinch force generated between the electrodes of resistance spot welders. Resistance welding uses a pair of electrodes to clamp two base metals firmly together prior to and during application of electrical current. Poorly clamped parts result in a defective joint. A correctly clamped assembly aids in reducing the resistance in the joint and allows the current flow to properly heat the base metals to weld the part.
-
-
Product
Sensor Products: Weld Force Probe Auditing System
90061-XH Series
-
This system is ideal for field measurement and data logging of forces between the tips of resistance spot welders. The system consists of a handheld sensor and portable readout/ data logger (PMAC 2000).
-
Product
ThermalAir Series Temperature Forcing System
ThermalAir TA-1000B Rack Mount Test System
-
The ThermalAir TA-1000B high capacity thermal air stream system is used for temperature testing, fast thermal cycling, and device temperature characterization of components, hybrids, modules, PCBs, and other electronic and non-electronic assemblies at precise temperature from -25°C to +200°C.
-
Product
Reusable ICP® Strain Gauge
-
This high-resolution dynamic alternative to bond foil strain gauges uses a quartz sensing element in a durable, titanium housing. It has 0.0006 microstrain resolution, 5 volt output, 100k Hz frequency response and 0.5 gram mass for lightweight test articles. The reusable sensor comes with a calibration certificate, attaches to the test specimen in 60 seconds and is removed in 10 seconds.
-
Product
LAP's Laser Gauge For Straightness Measurement Of Bars And Tubes
Check X-Line
-
This process is unique on the market and was developed with our partner sema Systemtechnik. You receive a verifiable quality assurance of your rods or pipes in the current production. The modular design allows individual configurability and can be easily integrated into the existing system. Benefit from the competence and experience of two strong partners.
-
Product
Split Ultrasonic Level Gauge
HR9100D
-
HighReach Measuring & Controlling System Co.,Ltd
Stable and reliable / We select high-quality modules and key components from the power supply part to select high-stability and reliable devices, which can directly initiate imported instruments.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type Q, Ø0.80mm, 305gf
K100-Q080305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style Q, Tip Diameter Ø0.80mm, Spring force 305gf, Steel with Gold Plating.
-
Product
Multifunction Engine Gauge
1U378-series
-
This 3” instrument combines the three essential engine parameters in a compact package. Rugged D’Arsonval meter movements with two jewels are used to indicate cylinder head and oil temperatures. A brass bourdon tube mechanism precisely indicates oil pressure. A selection of fittings is available to simplify installation.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type C, Ø1.50mm, 155gf
K100-C150155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style C, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
Product
Force Sensors
-
Is defined as a transducer that converts an input mechanical force into an electrical output signal. Force Sensors are also commonly known as Force Transducers.
-
Product
Destructive Coating Thickness Gauges
-
Designed for measuring on a non-metallic substrate or assessing the thickness of a multi-coat paint, Elcometer offer a range of destructive coating thickness gauges such as the Elcometer 121/4 and Elcometer 141 that are portable and easy to use.
-
Product
Thickness Gauge
124
-
The Elcometer 124 Thickness Gauge is used to measure the peak-to-valley height of a surface profile moulded in the Elcometer 122 Testex® Replica Tape.
-
Product
Coating Thickness Gauges
-
Non-destructive coating thickness measurement of non-magnetic coatings, e.g. paint, enamel, chrome on steel, and insulating coatings, e.g. paint and anodizing coatings on non-ferrous metals.
-
Product
Thickness Gauge
-
Hildebrand Prüf- und Meßtechnik GmbH
You can select a Thickness Gauge based on a specific standard, a specifiy material or foot diameter and weight/pressure.
-
Product
Gauge Type T Thermocouple Wire
W-TW-40
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Atomic Force Microscope
3DM Serirs
-
Park Systems has introduced the revolutionary Park 3DM Series, the completely automated AFM system designed for overhang profiles, high-resolution sidewall imaging, and critical angle measurements. With the patented decoupled XY and Z scanning system with tilted Z-scanner, it overcomes the challenges of the normal and flare tip methods in accurate sidewall analysis. In utilizing our True Non-Contact Mode™, the Park 3DM Series enables non-destructive measurement of soft photoresist surfaces with high aspect ratio tips.
-
Product
Analog Pressure Gauges
-
Analog pressure gages use a needle to indicate the pressure sensed on a dial scale. Analog pressure gauges are inexpensive, easy to use, and don’t require a power source.
-
Product
Force Sensors
-
Piezoelectric force sensors, respectively piezoelectric force transducers or load cells, are perfectly suited for the precise measurement of compressive and tensile forces, both in highly dynamic applications and in quasi-static processes. In universities and industry, for basic research or quality assurance: exact data is always essential in order to measure force characteristics and make processes more cost-effective. Thanks to their rugged design, piezoelectric force sensors from Kistler keep precise track of quasi-static and highly dynamic force processes, even when conditions are difficult. Our force sensors can also handle simultaneous measurements of multiple orthogonal force components.
-
Product
Pedal Force Load Cells
-
Pedal Effort Sensors are designed to measure load applied to the brake, accelerator, and clutch pedals during acceleration, deceleration, and transmission shift events. The units are compact and light weight, making them easy to install and remove.
-
Product
Tool, Inspection Depth Gauge, Micro Coax, Receiver
910121179
Inspection Tool
Tool, Inspection Depth Gauge, Micro Coax, Receiver
-
Product
Bore Gauges Xtreme 3 Digital Smart
-
• Great measuring range (2 - 300 mm)• Integrated Bluetooth® technology• Blind bore measurement from 2 to 6 mm and from 12.5 mm• Fixed anvils• UKAS certificate included with all rings• UKAS certificate included with each instrument• Manufactured according to DIN863• Memorization of 4 ring gauges values• Water and coolant resistant, protection rating IP67 according to IEC 60529• Programmable by PC• S_Connect Proximity
-
Product
Pfund Thickness Gauge
3233
-
Available in aluminium or stainless steel this instrument consists of two concentric cylinders, one sliding inside the other. A spherical glass lens, which has engraved measurements, is fitted to the end of the central cylinder and when pressed into the wet film, leaves a circular trace.The diameter of the mark on the lens is measured and, using the supplied conversion table, the thickness of the coating can be easily assessed.Ideal for measuring the thickness of wet translucent products such as varnishes, oils etc.Measurement range of 2.25 - 360μm (0.09 - 14.17mils)
-
Product
Precise Temperature Forcing System
TA-5000A Series
-
The ThermalAir TA-5000 Series of temperature forcing systems bring precise thermal testing capabilities directly to your test application, exactly localizing to where thermal conditioning temperature cycling is required. ThermalAir TA-5000 temperature systems provide flexible thermal test solutions for an array of products and technologies.
