Wideband Test
-
Product
Test Equipment
Digital Multimeter
-
*True RMS*2,000 counts*Auto/manual range*Auto power off (APO): 5 mins approx.*Over range display*Non-contact AC voltage detection (NCV) (with audible sound and visible indication)*Auto/manual AC/DC voltage measurement (600V AC/750V DC)*Auto/manual resistor measurement: 0-20MΩ (approximate)*Continuity check: approximate <50Ω buzzer sounds*Diode check*Auto/manual AC/DC current measurement (mA/mA/10A)
-
Product
Test Receiver
KH3932
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KH3932 EM1 test receiver is a fully automatic test receiver and the main tool for EM1 testing. The frequency range of the KH3932 receiver is from 9kHz to 300MHz. Equipped with a power absorption clamp, it can meet the power line disturbance power test. After the artificial power network is configured, the power terminal disturbance voltage test can be carried out. The machine has fast test speed and maneuverability. Strong, stable performance, convenient test data processing and other advantages. The KH3932 receiver uses the USB interface to exchange data with the computer, which makes the transmission speed fast and the bit error rate low. Connect to the computer for testing and use the operating environment familiar to the operator to improve work efficiency.The equipped operating software saves the data of a variety of external equipment, and supports plug and play a variety of external test equipment. The software and hardware are developed by our company. The whole machine uses a fully enclosed structure, and the chassis uses highly conductive materials with good shielding effects. Due to the use of specific technologies and processes, the problem of its own resistance is fundamentally solved. The measurement results are in the international general report format, which can be saved in the computer's hard disk or transmitted through the network, printed out directly, and saved using a USB storage device. The report is rich in content and can be printed directly according to user needs without additional editing.The measurement receiver complies with the requirements of the national standard GBT6113.101 and the international standard CISPR16-1.
-
Product
Testing Software
IEC 61850
-
Beijing GFUVE Electronics Co.,Ltd.
Intelligent substation has widely adopted IEC 61850 standard communication, the standardization of information model is the basis for intelligent substation equipment (or system) to achieve IEC 61850 communication. This module can test if the information model meet the requirements of DL/T860 standard, national network and related model specifications. It can test and control unit model, protection unit model, econometric model, condition monitoring model. It is selectable to test according to IEC61850-6 SCL grammatical rules, IEC61850-7 logic nodes and common data, the national network model standards and custom models.
-
Product
Test Equipment
Digital Clamp Meter
-
Is a large AC current digital multi clamp meter, integrated with 2000 Count, True RMS, auto and manual measurement, air-cored coil sensing technology.
-
-
Product
Microwave Testing
110H
-
The PICOPROBE® MODEL 110H is a high performance microwave probe which incorporates our patented coaxial design techniques and has inherent low loss and low dispersion characteristics.
-
Product
Usability Testing
-
Using our proven testing usability methodology, we deliver a 360-degree view on a product's operability by analyzing, identifying and benchmarking the weak spots in core features of the application and suggesting opportunities for improvement.
-
-
Product
Test Clips
-
Angled Nose allows tight hold on 66 blockUse on 110 block with jumper and bed of nailsUse on larger cables with single piercing nail
-
Product
EMC Testing
-
Does your product send or receive electromagnetic data? This can be analyzed using various tests. We investigate the interference immunity and emitted interference of simple electrical devices and complex machinery. Our EMC measurements and tests conducted in accordance with standards recognize all activity in the electromagnetic field and ascertain how immune to interference a piece of equipment is. We will also offer guidance on optimizing the product in terms of its EMC properties during the development phase.
-
Product
Functional Testing
-
Whatever your functional testing requirement, whether analogue, digital, or a combination of technologies, we have a solution. With over 2500 applications delivered in this field we have a level of experience that cannot be matched. Ensure the reliability of your product with our functional testing tools. Our functional test solutions range from completely standalone applications to those matched for our FLEX range of ATE test systems. Whatever your testing needs, we will help you choose the best option for you.
-
Product
Vibration Test
-
Vibration testing determines the dynamic effects on component part of vibration within the frequency ranges and magnitudes that may be encountered during field service. Vibration, for example, causes loosening of parts or relative motion between parts in the specimen, producing objectionable operating characteristics, noise, wear, and physical distortion, and often results in fatigue and failure of mechanical parts.
-
Product
Assembly & Testing
-
All components and subassemblies receive the highest attention to detail and workmanship, ensuring your satisfaction. From the initial design phase through to the final assembly, we are committed to producing the best possible products for our customers. Our team of skilled builders and assemblers take pride in their work and are committed to producing the best possible products.We thoroughly test and inspect all of our products before they leave our facility, and we stand behind their quality and workmanship. We are confident that you will be satisfied with your purchase, and we ensure that every product meets our high standards of quality control before it is shipped.If you have any concerns about the quality of your product, please don't hesitate to let us know. We are always happy to address any issues and ensure your complete satisfaction with our products.
-
Product
Accessibility Testing
-
It is a social responsibility to provide the perfect accessibility of software application to the differently-abled populations. ImpactQA ensures this by providing service across WCAG guidelines which are published by the Web Accessibility Initiative (WAI) of the World Wide Web Consortium to provide the best coverage in terms of accessibility testing quality. It is the only approach you can know for assured that your website, app, multimedia or electronic document is accessible to people with impairment. Usually, people with disabilities use convenient technology which helps them in operating a software product.
-
Product
PRODUCTION TESTING
-
The Production Test Department is a component of the Engineering Department where production test technicians perform routine factory testing in accordance with approved test procedures. Most of the electronic testing is automated, whether ambient acceptance testing or environmental ESS testing.
-
Product
Test Prods
-
Test prod with 4mm plug, test prod with 2mm pin, safety test prod, test prod 2mm, test prod 4mm, miniature test prod.
-
Product
Testing Services
-
Austin Labs is the industry leading third-party testing facility. We help our customers overcome testing challenges in their products including Data Integrity, Performance Analysis, Protocol Analysis and compliance, Error Injection, Signal Integrity, Electrical Compliance, Interoperability, Technical Consulting, Design and Feasibility.
-
-
Product
Strength Testing
-
Sataton Instruments Technology CO., Ltd
Air permeability tester is professional designed to determine the permeability of materials to air. By testing the rate of flow of air passing perpendicularly through a given area of tested sample under a given pressure over a given time period, the tester can provide results of air permeability performance by calculation the indices. The air permeability testing instrument is applicable to many type of materials, including industrial fabrics, nonwovens, made-up textiles, paper and board, foam and other materials.
-
Product
Hipot Tests
-
The hipot test (high potential test) or dielectric withstand test, is used to determine the insulation and dielectric strength. It is carried out on modules, devices and systems of protection class I + II. In this test, the insulation of the test object is subjected to greater stress by the high voltage than in normal operation. It is determined whether the insulation of all current-carrying conductors, as well as the safety distance to the enclosure, is sufficient and complies with the legal requirements under normal operating conditions.We will be happy to assist you with any questions or solutions to problems.You will find a large selection of high-voltage testers in our comprehensive shop.Questions? We are always at your disposal.
-
Product
Low Cost Microwave Wideband Electro-absorption DFB Transmitter
MT62 (40KHz~33GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MT62 series microwave DML optical transmitter, are able to transmit 33G microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 60Gb/s high speed communication system.
-
Product
Meter Testing
METES
-
Meter test systems with high accuracies of up to 0.02% and a wide measuring range for precise measurements in single- and three-phase applications. The meter test systems of the METES series are used to test the accuracy of Ferraris meters and electronic electricity meters under any operating conditions. The impact of system perturbations such as harmonics or flicker on the meter can be taken into consideration during tests.
-
Product
Motor Testing
-
Electronic Systems of Wisconsin, Inc.
ESW's Motor Test Systems come fully equipped with the latest industry features based on your testing needs. The on-screen display in our testers make it easy to read, track, and record your motor information during the testing process. We realize this importance and want to make sure you never have to worry about losing key information ever again. Performance and reliability are important, so we make sure you will have full confidence of every motor you test, whether you place it in your product or send out the door to your customer. ESW's design team works closely with you to determine the tests you need, in order to make a system that will meet all your testing needs. See the slideshow below to see some of our Motor Testers.
-
Product
Test Patterns
DisplayMate Multimedia Edition
-
DisplayMate Technologies Corporation
DisplayMate Multimedia Edition is the most advanced and powerful version of DisplayMate ever, with lots of proprietary and highly innovative suites of test patterns for setting up, tuning-up, calibrating, testing, evaluating, diagnosing, and analyzing CRTs, analog and digital LCD, Plasma, DLP, LCoS, and SXRD monitors and projectors, microdisplays, video boards, color printers, TVs and HDTVs, NTSC/PAL Television encoders and decoders, and more.
-
Product
Automation Testing
-
If you want to test all the major features of your application just before release, but you are short of time for complete testing, opt for Automation Testing.
-
Product
Network Testing
-
Service Providers are under significant pressure as service revenues plateau, competition intensifies and traffic growth skyrockets. Service Providers have relied on Enghouse Networks automated network testing for decades because this mission-critical solution adds significant and tangible business value. The solution enables Service Providers to improve network reliability and performance, accelerate time to revenue for new services, minimize expensive truck rolls and improve customer satisfaction.
-
Product
Test Tables / Test Consoles
-
Adaptronic test tables and test consoles are a decisive component of the adaptronic kit for the assembly of comfortable and high-quality test systems for the wiring test of manufactured cable harnesses of all types.
-
Product
Leak Testing
T SERIES
-
The new T series marks the evolution of the leak testers for the industry. A touch of innovation that fosters man-machine interaction thanks to the innovative tempered glass touch capacitive panel and other technological innovations that make the range, the natural evolution of the previous M series, the new benchmark for testing and proof brought.
-
Product
Test Sockets
BGA/LGA
-
There are a lot of options when it comes to bench test sockets. Save yourself and your lab time, money and frustration by working with Ardent for truly customized test socket solutions to meet your needs and do the job with high performance, reliability and quick turnaround that you need and deserve.
-
Product
Test Probes
E-Series
-
Your product descriA full portfolio designed for general purpose test on bare boards, surface mount assemblies and other forms of test specially to meet any needs.ption goes here.
