PCI Express Test
See Also: PCI Express, PCI Express Analyzers, PCIe
-
Product
PCI Express Digital I/O Cards With Counters And COS Detection
PCIe-DIO-24DCS, PCIe-DIO-24DC, PCIe-DIO-24DS, and PCIe-DIO-24D,
-
This product is a x1 lane PCIe DIO board available in four models ranging from basic DIO to advanced COS detection and Counter/Timer capabilities. The card emulates an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C can be further broken into two 4-bit nybbles via software and configured as either inputs or outputs.
-
Product
PCI Express System Timer (USB Interface)
SKU-032-01
-
The MiniPCI Express System Timer uses a standard USB interface to synchronize IP signals. This system timer provides accurate clock timing for Asterisk® open-source PBX software.
-
Product
ARINC-429 Module
M4K429RTx
-
The M4K429RTx is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 4000 family of carrier boards. The module supports up to ten ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word.
-
Product
Flexible Cable, 2.4 Mm To 3.5 Mm
85134H
-
The Keysight 85134H is a 62.9 cm (24.75 in) long1 flexible cable with a 2.4 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss greater than or equal to 16 dB. Insertion loss is 0.31 * sqrt (f) + 0.2 (where f is frequency is GHz) for the test port connector and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 2.5 inch radius. Stability1 of the Keysight 85134H is less than 0.12 dB and phase is less than 0.13o * f + 0.5o, (where f is frequency in GHz).
-
Product
Test Port Adapter Set, 3.5 Mm (Test Port) To Type-N
85130C
-
The Keysight 85130C test port adapter is designed to protect the test set port when it would be directly connected to the device under test. These adapters have a special rugged female connector designed for connecting to the network analyzer test port. This special connector will not mate with a standard male connector, but converts the rugged test set port to a connection that can be mated with the device under test. The set contains a 3.5 mm to type-N male adapter and a 3.5 mm to type-N female adapter. The frequency range for these adapters is dc to 18 GHz with a return loss of 28 dB or better.
-
Product
PCI Bus Carrier
APC8621A
-
This board interfaces industry-standard Industrial I/O Pack (IP) modules to a PCI bus on a PC-based computer system. The half-length card is ideal for use in smaller PC chassis.
-
Product
PCI bus Test Adapter
pcibus1b
-
All important PCI bus signals routed to pin headers for easy connection of logic analyzer. Filter assistance for logic analyzer: D-FF to delay FRAME# by one cycle. To see actual PCI data transfers, filter for FRAME2# high + FRAME# low (address phase), or IRDY# low and TRDY# low (data phase). Business card size. Notched for 5V PCI bus (can be used on 3.3V bus with mechanical modification).
-
Product
PCI Card
EXC-8000PCIe104/xx
-
The EXC-8000PCIe104/xx card for PCI/104-Express systems supports up to four dual redundant 1760 channels using the M8K1553Px(S)-1760 module and is compatible with all common variations of MIL-STD-1760 (A,B). In addition, Checksum, SRQ bit and Header Words are supported on each channel.
-
Product
PCI Module
PCI-ECL-II
-
PCI-ECL-II - with Spartan 6 FPGA, 16Mx32 SDRAM, 20 ECL TX , 20 ECL RX, and 12 TTL IO
-
Product
Single Stream STANAG3910/EFEX Test And Simulation Module for PCI
APXX3910
-
STANAG3910/EFEX Test and Simulation module for PCI with 1 dual redundant HS/LS channel and onboardFibre Optic Front End (FOFE). Easily select between EFAbus and EFEX modes for Tranche II Eurofighter. The APXX3910 is a functional replacementfor model APX3910.
-
Product
Wafer-Level Parametric Test
-
Wafer-level reliability engineers need to reduce test time without sacrificing measurement quality and accuracy.
-
Product
PCIe-8432, PCI Express, 2-Port, Isolated, RS232 Serial Interface Device
781744-01
-
The PCIe‑8432/2 is a high-performance interface for high-speed, port-to-port isolated communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial … interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
96/48-CH Opto-22 Compatible PCI Express Digital I/O Cards
PCIe-7248/7296
-
ADLINK"s PCIe-7248/7296 are high-density parallel digital I/O boards with 96/48 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCIe-7248/7296 can utilize the Opto-22 external devices. The PCIe-7248/7296 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCIe-7248/7296 provides 4/2 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCIe-7248/7296 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCIe-7248/7296 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
Product
PCIe-8430, PCI Express, 2-Port, RS232 Serial Interface Device
782122-01
-
The PCIe‑8430/2 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard … COM ports for compatibility with programs that use serial communications.
-
Product
Squid Carrier Board™ Family PCI Express Carrier Board for 8 MiniPCI Express Modules
SKU-085-01
-
Squid PCI Express Carrier board for MiniPCIe modules is the first product in the Squid PCI Express Carrier Board™ family. PCI Express Carrier board was designed to expand modern motherboards that have PCI Express interface. It allows connection of up to 8 MiniPCI Express half or full-size MiniPCI Express modules to the one motherboard’s PCI Express slot.
-
Product
Flying Prober Test System
QTOUCH1404C
-
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built high resolution Vision Camera for easy monitoring of probe needle contact. The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision.
-
Product
MIL-STD-1553 A / B Test And Simulation PCI Module
PCI-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
PCI Matrix Cards
-
PCI Matrix cards are available in the following:*Reed relay based matrices available in 22x4, 22x8, 44x4 or dual 20x4 formats with 1-pole, 2-pole or 1-pole screened relays*2 Amp electro-mechanical relay based 1-pole matrices available in 32x2, 32x4, 16x4, 16x8 or 8x8 formats.*Select modules are supplied with our eBIRST Switching System Test Tools, these tools provide a quick and simple way of finding relay failures within LXI, PCI and PXI switch systems.
-
Product
PMC to PCI Adapters
-
The PMC to PCI, PMC to CPCI and PMC to PC/104+ adapters enable the use of the PMC650 or PMC850 bus analyzers in PCI, CompactPCI and PC/104+ systems. The PMC analyzer plugs onto the adapter and then the mated adapter and analyzer plug into a PCI, CompactPCI or PC/104+ system. These passive adapters route the bus signals from the analyzer to the bus with minimal trace length and impedance matching. The adapters provide the full 64 bit interconnect between the analyzer and the bus.
-
Product
PXI Express Embedded Controller
PXIe3110
-
The PXIe3110 is the most compact andpowerful 3U one-slot embedded controller forthe PXI Express and CPCIexp platform. With itshuge and future-ready interface capabilities,it runs perfectly with most test and measurementapplications.The Controller is driven by a 7th generationIntel® Core™ processor combined with up to32 GB DDR4 memory and easily supports highbandwidth applications with its PCIe Gen3system and storage interconnectivity.
-
Product
PCI Express
PCIe
-
PCI Express (PCIe) has become the leading interconnect technology to succeed the Peripheral Connect Interface (PCI) architecture. The PCI Express(PCIe) architecture retains the PCI usage model and software interfaces for investment protection and smooth development migration. The technology is aimed at multiple market segments in the computing and communication industries, and supports chip-to-chip, board-to-board and adapter solutions. PCI Express 5.0 currently runs at 16GT/s or 32Gbps per lane in each direction, providing a total bandwidth of 128GBps in a 16-lane configuration which is the largest size in use.
-
Product
PCI Express Optical Link Board
SIS1100-E2
-
The SIS1100-e2 is the follow up card to our SIS1100-eCMC board (without CMC carrier functionality). It was developed to extend the lify cycle of our PCIe to VME interface. For software/driver compatibility reasons we still employ the PEX8311 PCI Express to local bus bridge chip.
-
Product
PCI Express Flat Cable
SKU-043-01
-
12-inch PCI Express Flat Cable is used to connect a MiniPCI/MiniPCI Express/PCI Express host cards with PCI Express adapter boards.
-
Product
4-Port PCI Express
PEX 8617
-
The ExpressLane™ PEX 8617 device offers 16 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 4 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 16-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including workstations, communications, storage, and embedded systems as well as intelligent I/O modules and add-in cards.
-
Product
PCIe-8431, PCI Express, 16-Port, RS485/RS422 Serial Interface Device
780592-02
-
The PCIe‑8431/16 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PCI Express x4, Gen3 XMC Carrier
TPCE278
-
The TPCE278 is a standard height PCI Express Revision 3.0 compatible module that provides one slot for a single-width XMC module used to build modular, flexible and cost effective I/O solutions for all kinds of applications like process control, medical systems, telecommunication and traffic control. The TPCE278 is a versatile solution to upgrade well known XMC I/O solutions to the PCI Express signalling standard. The PCI Express x4 link from the host board to the XMC module is enhanced by a PCIe Gen3 Redriver, allowing safe operation of XMC modules on PCIe mainboards.
-
Product
PCI Express 16 Isolated Input Digital Interface (3-13V)
8006e
-
The 8006e PCI Express digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, pushbuttons, and other user inputs. The inputs can sense both AC and DC voltage while providing optical isolation, which eliminates spikes and surges present in industrial environments. The board is PCI Express X1 compliant and is compatible with any PCI Express slot.
-
Product
Squid PCI Express Carrier Boards for M.2 SSD Modules
SKU-064-2X
-
Flexible x1 PCI Express to 3 MiniPCI Express Splitter (Splitter) was designed to expand modern motherboard (ATX, mini ATX etc.) that have PCI Express interface. It allows you to connect up to three MiniPCI Express add-in boards to the standard motherboard PCI Express connector.Splitter includes 3 MiniPCI Express adapter boards, x1 PCI Express host board and 3 flat PCI Express Cables.
-
Product
Basic 3U VPX-to-PCI Express (PCIe/PCI-e) Adapter
8065
-
The Technobox, Inc. P/N 8065 is a 3U VPX-to-PCI Express (PCIe) adapter that provides a convenient and cost-effective means for developing 3U VPX boards in a personal computer environment. It can also be used for production testing of 3U VPX boards. The adapter is a half-length PCIe card with the VPX card under test mounted close to the PCIe edge fingers to minimize signal lengths. When seated in a PC motherboard, the VPX card primary side faces upward to allow convenient access to components.
-
Product
12-Lane, 10-Port PCI Express
PEX 8713
-
The ExpressLane™ PEX8713 is a 12-lane, 10-port, PCIe Gen3 switch device developed using 40nm process node. PEX8713 offers PCI Express switching capability that enables users to create up to 9 downstream ports with varying widths including native x2. Today's processor south bridges offer x1 or x4 PCIe lanes, where x1 often does not provide enough bandwidth and x4's sheer size could waste valuable PCIe lanes.
