Showing results: 481 - 495 of 690 items found.
-
Focus-FX -
Kyoritsu Testsystem Co., Ltd.
This is general function test system. User can change board model easily by replacing a test fixture and changing inspection program. We have variety of measurement instruments such as FX modules which can control commercial instruments. It is possible to add required modules into existing units as they are connected by USB port. User can expand as per desired inspection specification.
-
GRS500 -
Polar Instruments Inc
Designed to help troubleshoot complex boards when fixture based tools are not a viable solution, the GRS500 is designed to help you compare the characteristics of good and faulty PCBs, using nodal impedance test, and a "Videosection" technique which presents you with high resolution images of a good board for use in live video comparison with the board under test,
-
F9 Systems, Inc.
The CalBlade backplane calibration fixture isdesigned to permit accurate and convenient impedance and transmission measurements of a HM-Zd backplane. The CalBlade is used to calibratethe logic card connector interface to the backplane rather than to the usual far-end of the coaxial measurement cables. Very accurate impedance, skew and propagation delay measurements are possible since parasitic fixturing effects are removed.
-
Terotest Systems Ltd.
In-circuit test works by checking all components are fitted correctly to the PCB and are within the correct electrical tolerance. In-circuit testers do this by interfacing to the board via a "bed of nails test fixture" and programs can be generated via CAD data. They offer a quick and easy method of checking the manufacture of the board and also offer a reliable and simple fault report.
-
YAVHF3X4C50 -
6TL Engineering
Fixture friendly. Use this product inside a Faraday chamber, and benefit from the fact that wiring in-out the chamber is drastically reduced! This module features three multiplexers in cascade configuration, for frequencies up to 2,5GHz. In/out is through SMB connectors, selectable for 75 and 50 Ohm. There’s direct control of the relays (24Vdc) or integrating CAN bus interface.
-
YAVHF3X4C -
6TL Engineering
Fixture friendly. Use this product inside a Faraday chamber, and benefit from the fact that wiring in-out the chamber is drastically reduced! This module features three multiplexers in cascade configuration, for frequencies up to 2,5GHz. In/out is through SMB connectors, selectable for 75 and 50 Ohm. There’s direct control of the relays (24Vdc) or integrating CAN bus interface.
-
YAVHF3X4 -
6TL Engineering
Fixture friendly. Use this product inside a Faraday chamber, and benefit from the fact that wiring in-out the chamber is drastically reduced! This module features three multiplexers in cascade configuration, for frequencies up to 2,5GHz. In/out is through SMB connectors, selectable for 75 and 50 Ohm. There’s direct control of the relays (24Vdc) or integrating CAN bus interface.
-
N1425B -
Keysight Technologies
The N1425B is designed to operate specifically with the B2985B/87B. It can hold DUTs with large terminals being used with the N1426C. The N1426A with the N1425B is available for measurements of small DUTs such as PC boards or IC sockets. The N1426B with the N1425B enables the construction of simple custom-made test leads. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1425B to the B2985B/87B.
-
N1425A -
Keysight Technologies
The N1425A is designed to operate specifically with the B2985B/87B. It can hold DUTs with large terminals being used with the N1426C. The N1426A with the N1425A is available for measurements of small DUTs such as PC boards or IC sockets. The N1426B with the N1425A enables the construction of simple custom-made test leads. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1425A to the B2985B/87B.
-
Virginia Panel Corporation
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. The G12x uses the same platform and slides as the G12, providing support up to 180 lbs (81 kg) to accommodate the largest fixtures. G12x accepts ITAs designed for both the G12 and G12x.
-
YAVTB000 -
6TL Engineering
When wiring a test fixture, you often have a need to join three or more wires onto the same test point. This module solves this problem, adding test points for manual test probes and a 4 position DIP switch. Circuits 1 and 2 feature up to 5 poles in parallel to increase the space for power supply terminals.
-
TPA-GFM -
High Power Pulse Instruments GmbH
*Electrically isolated probearm for GND needle contact or general purpose DC, twin-wire HBM or flexible pitch VF-TLP/TLP/HMM/HBM force/sense probing based on the HPPI GF-A flexible pitch setup.*Suitable to mount the GF-A ground fixture needle for flexible pitch measurements. In addition a cable (e.g. for HBM) can be directly connected to the contact pin.*High stability
-
Circuit Check, Inc.
We are the only test engineering firm in the US that specializes in both test fixtures and test systems. This allows us to implement solutions that others can’t. Circuit Check’s reference test systems are built upon our common platforms. Our solution oriented approach ensures tailored test systems with maximum flexibility, while at a low investment cost.
-
95TM -
Com-Ten Industries
The ComTouch controller reports current reading, force results, test stand direction, limit switch warnings, test stand speed, and error messages. Designed to be rugged, sturdy, and easy-to-use, this test stand is built to last. Just select from our wide line of fixtures for standard tensile testing or install an optional compression cage for testing in compression.
-
Terotest Systems Ltd.
Backplane and cable test systems from Terotest include LINX, a fixtureless test system. Each LINX test card plugs directly into the unit under test, which removes the necessity for long test cables and fixtures. This is called distributed testing and results in dramatically lowered costs. LINX is extremely easy to use, with a self-learn function or input from CAD.