Showing results: 451 - 465 of 690 items found.
-
410104258 -
Virginia Panel Corporation
The 75 Module, triple tier ITA is rugged and perfect for high I/O test and measurement applications. This ITA is made of steel to prevent any deflection caused by the high insertion forces from the available I/O. The added tapped holes on the back of the frame allow you to attach an enclosure or custom fixture.
-
TDK RF Solutions Inc.
By combining the latest in LED technology with the unmatched illuminating dynamics of prismatic glass, this High Bay LED luminaire brings a superior, incomparable proficiency and reliability to the table. With its remote driver capability, the TDK HBLED-540 High Bay LED Light Fixture is ideal for EMC chambers with minimal RF emissions.
-
Campbell Scientific, Inc.
The solar radiation sensors that Campbell Scientific offers come in a variety of designs: pyranometers, net radiometers, quantum sensors, and pyrheliometers. These sensors measure various aspects of the energy imparted by the sun on the Earth’s surface. A leveling fixture fitted with a bubble level may be required to accurately install solar radiation sensors.
-
JRE 2525 -
JRE Test, LLC
Originally designed for testing rack mounted RF Sensing equipment, the roomy JRE 2525 is ideal for large wireless devices such as; Rack Mount Mesh Network AP's, Cellular/LTE/4G Base Stations, Wireless Laptops, Test Fixtures for testing Large RF Modules, and other large RF devices.
-
Z-Axis Connector Company
Custom test sockets are traditionally expensive to build and maintain. To reduce these costs, consider: Using rapid prototyping techniques to build a housing. Using replaceable Z-Axis Connectors. Depending on board layouts and compressed height, these sockets or test fixtures can achieve high numbers of mate/de-mate cycles and operate at GHz frequencies.
-
Q1 Test, Inc.
In-circuit-testing (ICT) is usually used on mature products, especially in subcontract manufacturing. It uses a bed-of-nails test fixture to connect with multiple test points on the PCB’s bottom side. With sufficient access points, ICT can transmit test signals into and out of PCBs at high speed to apply evaluation of components and circuits.
-
Beehive Electronics LLC
The Beehive Electronics 135A RF Helmholtz coil generates a well-controlled, uniform magnetic field. It can be used to calibrate magnetic field probes, such as the Beehive 100 series, or for testing the susceptibility of other devices to magnetic fields. The Helmholtz coil comes supplied with a fixture that makes it easy to calibrate Beehive 100 series probes.
-
Flex 40 -
A.T.E. Solutions Ltd.
The Flex 40 is generally suited to the larger Generic Test Systems. A Flex 40 is a dual bay version of the Flex 30 that gives us the ability to fit a wide range of external instrumentation, PXI, custom modules and large fixture interfaces. Generally it is fitted with the VPC G12x Interface but this can be changed to suit the requirement.
-
Leak Testing -
TQC Ltd
TQC have supplied automatic leak test / pressure test equipment for over 25 years. The supply has included simple manually connected leak test fixtures to fully automatic, high speed production leak test facility. TQC supply leak testing equipment to meet the customers requirements.
-
Photo Emission Tech., Inc.
The I-V Curve Data Acquisition includes a fixture for holding cells for testing (see Figure 1 below). This fixture can accommodate cells from small to up to 100 mm x 100 mm. Adjustable cell stops, in the X & Y-axis, are provided to consistently locate the cells for testing. Two micro-manipulators are provided as shown in Figure 1. Each micro-manipulator has two spring loaded contacts to allow 4-wire measurement even for cells that have top contacts only. Two back-side voltage contacts are embedded in the Plate (galvanically isolated from the Plate) and make good electrical contact when the cell is held down by vacuum to the plate. All voltage and current probes are gold-plated. The cell is held down with vacuum during testing (built-in vacuum pump).
-
Instron
The Instron® Curved Needle Testing System is built on the 5900 system platform and is ideally suited for needles used in abdominal, fistula, vascular, intestinal, or other surgical procedures. This system provides two different needle testing solutions: one for curved needle puncture testing and one for bend testing. The curved needle puncture testing fixture is used to evaluate needle sharpness and insertion force, while the needle bend testing fixture is used to evaluate flexural properties of the needle during use. With its tabletop design, the Curved Needle Testing System has a small footprint and takes up minimal bench-top space. The testing system operates with Instron Bluehill® Universal software that provides test control, data acquisition, test results, and reports, as well as a large library of calculations.
-
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicators within this range are encased so that the operator can either use it on the move (if battery powered) or be a permanent fixture, e.g.: wall mounted.
-
Radiometrics Midwest Corporation
One of the more difficult tests to understand is shielding effectiveness or transfer impedance. The data from these tests may vary dramatically based on the test method selected, test fixture, test setup, measurement sensitivity, test personnel, etc. At Radiometrics all shielding effectiveness test are performed or supervised by NARTE Certified engineers.
-
Datest
Customer-supplied or developed in-house• Ruggedization of existing (lab-built) fixtures• Co-develop hardware/software• Deployment, implementation, and training• Engineering evaluation tools• Design verification• Medical device evaluation• Manufacturing test systems• Verification test systems• Go/No-go tests• Serialization, recordkeeping, and datalogging• Troubleshooting failed units with other test platforms
-
TA-55 -
Tech-Aid Products
Radar altimeter panel designed after the ALT-50A test fixture. (Ref. Fig. 5-1). Panel allows testing of the indicator or R/T independently or together. An internal power supply is provided to support stand alone testing of the indicator. This panel contains a 4 digit DVM and comes with enclosure. This panel will allow by the book testing.