AC DC Electronic Loads
-
product
DC Power Supply
PW-7033
*Portable type, small size design*Overload protection*3 sets output: 0~32V/0~3A x 2 + 5V/3A*Parallel: 0~64V/0~3A or + 32V ~ -32V/0~3A*Series: 0~32V/0~6A*3 digits, 4 sets LED display, Green is display for voltage, Red is display for current, easy to read, no mistakes.
-
product
Coaxial Terminations (Loads)
Keysight offers a variety of coaxial terminations (loads) solutions to terminate up to 75 Ohm coaxial systems with precise, low reflection loads for superior RF performance.
-
product
DC System Power Supply, 40V, 19A, 760W
N5746A
The single output, 760W N5746A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current.
-
product
Load Cell Junction Box
SY-JUNCTION-IP67
The SY-JUNCTION-IP67 load cell junction box is useful to parallel connection of load cells and take just one cable out to almost any indicator, either batch controller or a PLC.
-
product
Unclamped Inductive Load Tester
ITC55100C
The system has been designed around a very powerful micro-controller that gives it a timing resolution of 40ns, twenty times faster than the previous model. Its response time to the peak and zero current is improved ten times. Combined this gives greater accuracy for the charging and avalanche times and for the reported peak drain current.
-
product
RF Electronic Calibration Module (ECal), DC/300 KHz To 26.5 GHz, 4-ports
N4433D
The Keysight N4433D RF electronic calibration (ECal) module makes calibration of Keysight vector network analyzers fast, easy and accurate. The N4433D is a precision 4-ports ECal module that supports selection of 3.5 mm connector and can be mixed up to 26.5 GHz. Select either female-female, male-male, or female-male connectors.
-
product
AC Ionisation
AC Short Range
Fraser Anti-Static Techniques Ltd
AC static eliminators for manufacturers.
-
product
PWM Type AC Power Supply
LSP-5KVA
• Circuit Type: (IGBT) MPWM Pulse Duration Modulation • Input: 1 Phase 220V±10%, 50Hz/60Hz±5% • Output Voltage: HIGH/LOW Adjustable 1)1 Phase Voltage Range: (HIGH)0~300V, (LOW)0~150V 2) Nominal Voltage: +10%~+25%, -10%~-30% • Output Frequency: 50Hz, 60Hz, adjustable between 45 and 70 Hz, 400Hz • Load Voltage Stabilization Rate: ≦0.5% • Frequency Stabilization Rate: 0. 1% (Fix Point 50Hz, 60Hz and 400Hz) • Wave Distortion Rate: ≦2% (Resistor Load); Efficiency: ≧85% • Output Instruments: Frequency Indicator, 4-digits RMS digital frequency indicator, resolution is 0.1Hz Voltage Meter, 4-digits RMS digital voltage meter, resolution 0.1V Ampere Meter, 4-digist RMS digital ampere meter, resolution 1Ma Power Indicator, 4-digits RMS digital power indicator, resolution 1W Power Factor Meter Resolution 0.001 • Protective Devices: Over load, short circuit, over voltage, over current, over temperature protective and alarm devices • Operating Environment: Temperature 0~40℃ Relative Humidity 0~90%
-
product
DC Clamp Meter
Shenzhen UYIGAO Electronic Technology Co., Ltd
Is used to measure the DC currents.
-
product
DC Power Analyzers
DC Power Analyzer provides unrivaled productivity gains when sourcing and measuring DC voltage and current into a DUT. The Keysight N6705C DC Power Analyzer is a highly integrated instrument that combines up to four advanced DC power supplies, DMM, oscilloscope, arbitrary waveform generator and datalogger. It provides an easy-to-use interface, with all sourcing and measuring functions available from the front panel. The N6705C makes these tasks easy:
-
product
Data Loading Products
TechSAT's data loading products are available to support all standard ARINC data loading protocols: ARINC 615/615A/826/844 for ARINC 429 and Ethernet based data loading. For next generation aircraft, TechSAT's data loading solutions bring portability to data loading over the new generation of avionics bus and network types: AFDX®/ARINC 664, Avionic & Deterministic Ethernet, TTP, and ARINC 825/CAN
-
product
48V / 300 Amp Load
BD18-48P
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
product
Hipot Current Calibration Load Resistors
HPRS-HIPOT-LOAD
The IET HPRS-Hipot-Load is an excellent replacement for the Fluke 5320A-Load Hipot current calibration load resistors. The IET high power resistive load can be used with the Fluke 5320A Multifunction Electrical Tester Calibrator or standalone. It provides a high power and high voltage load to various hipot tester to create the leakage current needed to calibrate various manufactures hipot testers.
-
product
VME Load Card
WIENER VME load boards are designed to test VME crate power supplies and fan trays by drawing power from the VME backplane and dissipating it as heat. A series of switches on the module front panel allows for easy adjustment of the current draw for each voltage channel.
-
product
Electromechanical Switches DC to 40 GHz
Fairview Microwave’s electromechanical switches exhibit extremely low insertion loss repeatability with guaranteed levels of 0.03 to 0.05 dB over 5 to 10 million switching cycles, depending on the model. Performance includes low insertion loss of 0.3 dB with high isolation of 100 dB typical, and input power ratings of up to 70 watts CW and up to 1 watt for hot switching applications. These switches cover broadband frequencies from DC to 40 GHz and are offered in three configurations: single-pole double-throw (SPDT), single-pole four-throw (SP4T) and single-pole six-throw (SP6T).
-
product
Load Cells, Weighing and Force Sensors
We are pleased to offer Load Cells from both Zemic and Vishay. We are the exclusive UK distributor for Zemic load cells.
-
product
AC Ionisation
AC Power Units
Fraser Anti-Static Techniques Ltd
A power unit designed to serve large systems
-
product
AC Fuel Flow Signal Generator
TA-100
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
product
In Line Load Cell (10KN-50KN)
106, 107, 108 Series
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 50kN and 10klb with better than ±0.5% non-linearity. This type is also available with fully welded cover.
-
product
High AC Current Capacitor
LC1/LC2/LC3-RNM
Induction Heating Processing Equipment, Electric Current Welding, High Power Resonant Circuits, Motor Controls; Oscillating, Bypass, Coupling circuits, High AC Current applications, High-Frequency AC Filter and Medium Frequency Power applications.
-
product
Small Engine AC Motoring Dynamometers
SAKOR Technologies developed its new Small Engine AC Motoring Dynamometer specifically to meet the needs of engine manufacturers who must now comply with engine testing procedures required by new emission standards contained in 40 CFR Part 1065. These new requirements apply to almost every kind of small internal engine, including those in handheld power tools and lawn and garden tools.
-
product
AC Power Sources
BPS Series
AMETEK Programmable Power, Inc.
The BPS Series consists of multiple high power AC power systems that provide controlled AC output for ATE and product test applications. This high power AC test system covers a wide spectrum of AC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the BPS Series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the unit to its designated location (using included casters), plug it in, and the BPS Series is ready to work for you.
-
product
Power Divider, DC to 18 GHz
11636A
The Keysight 11636A is a dc to 18 GHz power divider for direct power dividing applications. The excellent impedance match of all three ports improves fault location measurements by reducing re-reflections. The Keysight 11636A power divider/combiner is recommended when making wideband comparison measurements with a Keysight 8757 scalar vector network analyzer.
-
product
Bipolar DC Power Supply / Battery Simulator
IT6400 Series
The unique bipolar voltage/current output makes IT6400 series can be used as a bipolar power source or a bipolar electronic load. The battery simulating function is especially applicable for development and high speed production testing of portable, battery-operated products.
-
product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2
The TMO-2 Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The units provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Full scale output is specified at plus or minus 10 VDC. The TMO-2 provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability for applications such as weighing scales. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
product
DC Earth Fault Locator
GFL-T + GFL-R
The DC Earth Fault locator is suitable to test the DC Battery System and Trace Ground Faults. The system is suitable for Power Plants, Sub-Stations upto 765KV and other industries. The system is highly capable in tracing and pin pointing the DC earth faults in a live system without requiring any shut downs. The receiver sensitivity of 1mA and better is capable to trace most complex fault.
-
product
Through Hole Type AC Current Sensor
CTF-400B
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Suitable for current measurements of main cable.*Measuring range:AC 1A~400A.
-
product
Automation Software For Aim-TTi Power Products Including LD And LDH Series Electronic Loads.
Test Bridge
Test Bridge software is a simple Windows application intended to make it possible to create a test sequence that can control up to four Aim-TTi products and record measurement results in graphical and tabular form.
-
product
Adapter, 2.4 mm (f) to APC-7, DC to 18 GHz
11902B
The Keysight 11902B is a metrology grade, 2.4 mm female to APC-7 adapter with dc to 18 GHz operation.
-
product
24 V DC Ionisation
Pulsed DC Long Range
Fraser Anti-Static Techniques Ltd
Sensing and adaptive ionisation for long range and wide area applications.





























