-
Product
Transducers
-
Transducer is a tonpilz piston source approximately 1/2 wavelength in diameter at the center of its operating frequency range and is designed with an industry standard mounting hole pattern through4-corner integral mounts which allows support for both new and existing vessel array configurations.
-
Product
Pitot Tube Flow Meter
PTFM-1000V2
-
The Pitot Tube Flow Meter, PTFM-1000V2 is a standalone interface for measuring exhaust gas flow rate of combustion engines. The system uses the tried-and-tested pitot tube principle with high-frequency transducers to accurately measure highly pulsating exhaust flows with a sampling rate of 1kHz. This rapid capture rate ensures that any pulsations or exotic behaviour in an engine is measured, and the unique design of the PTFM pitot tube means reverse flows can be measured with the same guarantee of sensitivity. The interface can be run standalone with a laptop, or seamlessly integrated to run alongside an analyser system without adding any more steps to the test cycle process.
-
Product
Vibration Sensors
-
Metra Mess- und Frequenztechnik in Radebeul e.K.
Metra has been developing and manufacturing piezoelectric vibration sensors Since 1954. There are transducers for nearly every purpose. Our product range includes accelerometers with charge and IEPE compatible output.
-
Product
Accessories
-
Check out the full line of quality Amprobe accessories, which are field tested to help you get the most out of your Amprobe tools, including:*Rugged test leads of all types and sizes for Amprobe instruments*Current transducers for maximum accuracy and safety*Temperature accessories for surface, air/gas, or liquid temperature measurements*AC relays for low-voltage control circuits*Adapters, software, carrying cases and more
-
Product
Sensors
-
A wide range of probes, sensors and signals is available for ALMEMO® data loggers and measuring instruments, which are connected via intelligent connectors with integrated data carrier. For common measuring tasks the connectors are configured at the factory and the measuring device automatically recognizes the connected sensor. All sensors can be calibrated, scaled and provided with a unique designation via the intelligent connectors. The programming always remains with the corresponding sensor, so that it can be connected to any input on the measuring instrument. Inaccuracies of a sensor can be corrected in the connector, thus turning simple sensors into precise transducers.
-
Product
Analog Power Transducers
ROCHESTER
-
AMETEK Power Instruments offers a wide range of Rochester Analog Power Transducers for meeting all of your power measurement needs. The transducers consist of two families of products; the Process and Ultra series. Each one is designed to provide an exact fit for your monitoring application.
-
Product
Power and energy calibrators
-
Three or single phase electric power/energy calibrator with power quality functions for calibration and testing of grid measuring appliance like power meters, power transducers or power quality analysers.
-
Product
Low Range Low Cost OEM Differential Pressure Transducer
P17
-
The P17 OEM Low Range Low Cost pressure transducer features high sensitivity to very low pressures with full scales available down to 0.1 In H2O. Output signal is 5 Vdc and power can be +5 to +28 Vdc. Zero and Span adjustments are included. The P17 has a robust steel sensor construction.
-
Product
Portable Digital Manometer
PS309
-
Featured are an integral variable reluctance transducer, solid state electronics module, 3 digit liquid crystal display (LCD)* and battery pack with six 1.5V penlight cells for truly portable operation. The units can also be powered from an external DC power supply or AC battery eliminator (converter) module. The transducer features all corrosion resistant materials in contact with the pressure media (both ports in differential units), very low internal cavity volumes and ultra-low volumetric displacement with full-scale pressure excursion. Transducer calibration is unaffected by dielectric properties of the sensed fluid. Gauge and differential transducers may be disassembled and range changed by simple diaphragm replacement.
-
Product
Wireless Transducers with GSM Modem
-
Wireless GSM data loggers for temperature, humidity, binary-u. counter input.
-
Product
Antennas
-
Is a specialized transducer that converts electric current into electromagnetic (EM) waves or vice versa.
-
Product
Multibeam Echosounder - Shallow Water
SeaBat T20-P
-
The ultimate combination of portability and performance. With the SeaBat Portable Sonar Processor mobilization time is reduced to help you focus on getting the job done. Fully adaptable to a wide range of applications the T20-P uses compact low-weight transducers in a 1°x1° configuration. The Portable Sonar Processor is water resistant and is capable of time tagging typical support sensors.
-
Product
NI-9425, 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
779139-01
Digital Module
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
-
Product
NI-9375, 30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
785192-01
Digital Input Module
30 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The NI‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The NI‑9375 offers isolation between the input and output banks from channel‑to‑earth ground.
-
Product
Signal Splitter
-
The Dynamic Signal Buffered Splitter protects sound and vibration sensor acquisitions from the unwanted effects of a parallel troubleshooting or diagnostic instruments. G Systems Dynamic Signal Buffered Splitter provides buffered and unbuffered outputs connected to the same signal input. Up to 16 sensors, typically accelerometers, proximity probes, microphones, and pressure transducers, may be connected to the 16 signal inputs.
-
Product
Pressure Sensors For Motorsport
EPT1500
-
The EPT1500 series of Pressure transducers has a miniature design using a hermitically welded, thin filmmeasuring cell, coupled with high level output circuitry. This technology ensures this sensor is suitable for some of industries harshest environments, including automotive, industrial hydraulics, refrigeration, off-road, construction and agricultural applications. The EPT1200 and 1500 series offer measurements in gauge and absolute pressure, with ranges up to 400 Bar and are backed by a one-year warranty.Miniature design | Rugged construction | Wide operating temperature range | Long life High performance
-
Product
NI-9411, ±5 V to 24 V, 6 Differential/Single-Ended Channels, 500 ns C Series Digital Module
779005-02
Digital Module
±5 V to 24 V, 6 Differential/Single-Ended Channels, 500 ns C Series Digital Module - The NI‑9411 works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and devices. The NI‑9411 is a correlated digital module, so it can perform correlated measurements, triggering, and synchronization when installed in a CompactDAQ chassis.
-
Product
4-CH 24-Bit Universal Input USB DAQ Modules (OEM Version Available)
USB-2401
Data Acquisition Module
The USB-2401 is a 24-bit, 4-channel simultaneous-sampling universal input USB DAQ modules featuring built-in signal conditioning circuitry, providing direct measurement of commonly used sensors including current output transducers, thermocouple, RTD, load cell, strain gauge, and others. Individual channels can be programmed to measure different signal types. The USB-powered USB-2401 is equipped with removable screw-down terminals for easy device connectivity, and the included multi-functional stand fully supports desktop, rail, or wall mounting.
-
Product
Short Leadtime Transducers
-
In addition to custom designs, we also have a carefully selected offering of transducers which can be ordered on a short lead-time.
-
Product
Digital Power Transducer
LP Series
-
*High accuracy 0.07% rd + 0.03% ro*Excellent long term stability*Outstanding over capability and temperature performance*Wide selection of input / output ranges*Meets ANSI C37.90 (1989) and BEAMA No. 219 tests*High magnetic field immunity*Real power - able to measure distorted waveform
-
Product
PCI-4461, 204.8 kS/s, 118 dB, 3.4 Hz AC/DC Coupled, 2-Input/2-Output Sound and Vibration Device
779307-01
Sound and Vibration
The PCI‑4461 is a high-accuracy data acquisition module specifically designed for sound and vibration applications. It provides simultaneous two-channel dynamic signal generation and simultaneous two-channel dynamic signal acquisition with six gain settings to configure the input range. The PCI‑4461 also includes software-configurable AC/DC coupling and integrated electronic piezoelectric (IEPE) conditioning to ensure precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. Common applications include audio test; automotive test; noise, vibration, and harshness (NVH) analysis; and machine condition monitoring.
-
Product
Transducers
-
Brüel & Kjær Sound & Vibration A/S
Transducers have been a core part of Brel & Kjr's business for more than 70 years. The quality of our transducers is world-renowned. It is the result of our vast experience and knowledge, backed up by meticulous testing and quality control. Furthermore, all transducers are calibrated individually before shipping. In turn, this ensures that you always receive the performance and durability you expect.
-
Product
Static Load Cells (5 N to 300 kN)
2530 Series
-
The Instron 2530 Series static load cells are precision force transducers engineered for versatile use in tension, compression, cyclic, and reverse stress testing, delivering accurate measurements down to 1/500th of their capacity. Individually temperature-compensated and calibrated, they support automatic recognition and electronic calibration, and are built to international force-measurement standards (ASTM E4, ISO 7500-1 class 0.5, and JIS B7721, B7733). With overload protection (150 % of rating without damage, 300 % without mechanical failure), the 2530 family offers consistent, repeatable performance across a wide force range (5 N to 300 kN).2530 Series load cells with capacities of 5 N to 100 N are for use with 3300, 3400, 5900, and 6800 Series testing systems.2530 Series Load cells with capacities of 500 N to 300 kN are for use with 3300 and 3400 Series testing systems.
-
Product
VCS
Control Parameters
-
Pre-test of the system for the purpose of evaluating the optimal parameters to be used for test performance Preparation for vibration testing is an important and labor-consuming process. It is attributed to the fact, that correct mounting of the transducers on the test specimen and selection of the reference transducer are crucial factors for the successful performance of the testing procedure.
-
Product
Computer Conversions GT Transducers
H25
-
Computer Conversions Corporation
Computer Conversions GT Transducers are brushless, Electromagnetic, Rotary Sensors used to provide Precise Absolute or Incremental Position, and Velocity feedback in harsh environments. All Computer Conversions Transducers are continuous rotation, bi-directional, and electronically passive devices (no electronic components to degrade or fail), that require zero maintenance, and may be installed in virtually inaccessible locations.
-
Product
Linear Variable Differential Transformers (LVDTs)
-
Whilst there are several ways to measure displacement, the Linear Variable Differential Transformer (LVDT) remains a popular transducer in most industrial applications. LVDTs initially were used as a means of taking dimensional readings in laboratories. They gained popularity in a wide variety of industrial monitoring and control applications, and whilst an LVDT is used to measure displacement the technology can be employed within other transducer types.
-
Product
Signal Conditioner
ClipX
-
Fast and digital signal conditioning for force sensors, load cells, torque sensors, pressure transducers, as well as temperature and standardized signals (current/voltage). Guaranteed measurement accuracy, even in harsh industrial environments with electrical interferences.
-
Product
Torque Measurement Trainer Module
-
Unitech Scales And Measurements Pvt. Ltd
Torque Measurement Trainer comprises of strain gauge based reaction type torque transducer, fulcrum arm of 1 M length with L angle to mount the sensor, Pan & weights with digital torque indicator to read the torque in Kg-m.
-
Product
Transducer Calibration
m+p SensCal
-
Regular transducer calibration is an essential requirement for maintaining the accuracy, reliability and repeatability of the results obtained from a measurement system. m+p international’s m+p SensCal program provides a quick and simple process for calibrating accelerometers (piezo-electric with charge output or IEPE, piezo-resistive, capacitive) in your laboratory, as well as velocity or displacement transducers.
-
Product
Acoustic Transducer
RESON TC 1037
-
Originally designed for underwater telephone systems, the TC 1037 is a rugged directional transducer ideal for operating at low frequencies.
