Showing results: 826 - 840 of 2118 items found.
-
BIRD 210 -
HGH USA
Testing detectors requires the implementation of ultra-low noise driving electronics and presenting high quality optical stimuli to the detector under test. This meets all these requirements and allows to test any type of detector by easily implementing the detector’s driving signals and providing exhaustive and accurate measurement results.
-
#TNC950AR -
NSI Industries
The Net Chaser Ethernet Speed Certifier and Network Testeroffers a complete solution to test and speed certify the data-carrying capabilities of Ethernet network cables up to 1 Gb and s by testing for noise in the network, detecting faults in the cable wiring, and ensuring that cables are able to support the speed capabilities of […]
-
Vidac Solutions
Partial Discharge testing is a way of detecting voids or imperfections in insulators that would lead to overheating and breakdown under normal operating conditions. Due to the nature of the signal being measured, this test is very susceptible to electronic and RF noise and a proper corona-free properly isolated test chamber is required.
-
Topaz -
Teledyne e2v
The Topaz series of industrial CMOS sensors include 2MP (1920 x 1080) and 1.5MP (1920 x 800) resolution devices. The sensors use state-of-the-art low noise, global-shutter pixel technology to offer powerful solutions and enable compact mobile designs for many applications.
-
SiTek Electro Optics AB
Functions according to the Lateral Effect Photodiode principle. It is an analogue device and therefore displays excellent position resolution. The resolution is determined by the system signal-to-noise ratio. It is operated in the biased mode. Typical applications include: distance andheight measurement, alignment, position and motion measurements and vibration studies
-
SiTek Electro Optics AB
Functions according to the Lateral Effect Photodiode principle. It is an analogue device and therefore displays excellent position resolution. The resolution is determined by the system signal-to-noise ratio. It is operated in the biased mode. Typical applications include: distance andheight measurement, alignment, position and motion measurements and vibration studies
-
E9988E -
Keysight Technologies
Short wire fixturing eliminates problems commonly found with long wire fixturing, such as noise and deterioration of test stability. This translates into transportable, repeatable and stable tests on your i3070 Series 5i, even if you need to deploy tests halfway across the globe, or on different manufacturing sites.
-
M9183A -
Keysight Technologies
The Keysight M9183A is a 6 digit PXI digital multimeter that measures common parameters such as DCV, DCI, ACV, ACI, 2- and 4-wire resistance, frequency, capacitance, and temperature. It offers40 ppm basic DCV measurement accuracy, excellent noise rejection, and handles inputs of up to 300 V.
-
LSS Series -
Noise Laboratory Co.,Ltd.
A simulator to reproduce “High energy induced lightning noise” which is induced by potential change on the ground, or done to power lines or telephone lines as result of lightning current.This immunity test is required by major standards including IEC61000-4-5 and JEC 210/212 and is widely used in many industries.
-
OE8000 -
OEwaves, Inc
RF Test Measurement System (TMS) utilizes microwave photonics techniques for automated measurement of ultra-low phase noise oscillators.
-
PI-41702 -
Pulse Instruments
The PI-41702 is a four channel bipolar DC Bias supply that can provide an output current up to 100 mA per channel. The output voltage ranges from –8 V to +8 V, and this card has special filter circuitry to reduce the output noise for those applications that require a low noise bias output. Additionally there is a ‘D’ type connector that allows the introduction of laboratory type supplies to reduce the noise further. To change from using the internal power supplies to external power supplies requires repositioning jumpers. The PI-41702 also has voltage and current sense for remote measurement of the voltage and current levels.
-
WMA-005 And WMA-005LF -
Falco Systems
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
WMA-01 And WMA-01LF -
Falco Systems
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
WMA-02 And WMA-02LF -
Falco Systems
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
LAB / HPL -
ET System Electronic GmbH
*Output from 5kW to 10kW*Output voltage up to 600V*Output current up to 500A*Dimensions: 19 "x 3 U x 620mm*Integrated load; voltage controlled*For 2-quadrant operation*Compact design*Low noise development for pleasant work in the immediate vicinity of the device