Broadband Test
-
Product
Broadband Test
458-3SLB
-
This compact, versatile unit accepts 1, 2 or 3 line modules or other products that use Telebyte's convenient line module form factor. At home in the lab or a high-volume production environment, it is capable of controlling from 1 - 24 channels and is ideal for testing DSL modems and other bandwidth-compliant telecom devices. While it can be used as a stand-alone unit, the built-in Control Module interfaces with a PC via RS-232, IEEE-488, or Ethernet. In addition, the 458 Universal GUI (included with purchase) may be used to control the unit from a PC. For added convenience, the Control Module firmware is field-upgradeable through the RS-232 port.
-
Product
TEM Cells
-
Transverse Electro Magnetic (TEM) cell or Crawford cell (named after its inventor) is used to generate accurate electromagnetic waves over a wide frequency range: DC (0 Hz) to GHz., EM waves generated in the cell propagate in transverse mode and have the same characteristics as a plane wave. It can be used to calibrate E-field broadband probes for testing radiated E-field immunity as well as for measuring radiated emission from a product with a spectrum analyzer/EMI receiver.TEM cell generates a consistent electromagnetic field for testing small RF devices such as wireless pagers, receivers, portable phones, etc.
-
Product
2.0 ~ 68.0 Gb/s Pulse Pattern Generator
CA9809
-
The UC INSTRUEMNTS CA9809 2.0 ~ 68.0 Gb/s Pulse Pattern Generator pulse pattern generator and error detector is a high performance, flexible and costeffective broad band data rate covered Pulse Pattern Generator that can operate from 2.0 Gb/s to 68 Gb/s. The CA9809 can be used with existing equipment to generate higher rate bit streams for use in telecom applications up to 68 Gb/s. Broadband test systems will benefit from the low power dissipation, precision connectors, and excellent output waveform characteristics. The compact size of the equipment allows the CA9809 to be placed at the measurement plane, reducing or eliminating artifacts related to long cables.
-
Product
Microwave Power Amplifier 10W 100 MHz to 20 GHz
GT-1000B
-
The Spanawave GT-1000B Microwave Power Amplifier offers linear high-power amplification across multi-octave bands. It is ideal for testing in EMC, wireless communications applications and Defense EW systems. For EMI/EMC and standards laboratories, the GT-1000B with 100 MHz to 20 GHz frequency range allows broadband testing without band switching or swapping narrow band amplifiers resulting in faster and more accurate testing.
-
Product
DSL/Gfast Test Software
-
Test Sentinel is a full suite of automated DSL and Gfast tools that allow a user to easily perform experiments and run standardized testing. This is the same set of tools used in our DSL and Gfast Testing Services to perform a wide variety of requests including Broadband Forum standardized tests and the Broadband Forum Gfast Certification.
-
Product
Clock Generation Devices
-
Analog Devices offers ultralow jitter clock generation products for wireless infrastructure, instrumentation, broadband, automatic test equipment, and other applications demanding subpicosecond performance. Our clock products are ideal for generating the high speed, low noise clock signals required to clock high performance analog-to-digital converters (ADCs) and digital-to-analog converters (DACs). ADI clock ICs integrate PLL cores, dividers, phase offset, skew adjust, and clock drivers in small chip scale packages.
-
Product
Broadband Network Test
-
Whether testing via Voice Switch, DSLAM, OLT or external access device, Enghouse LoopCare comprehensively manages testing in mixed technology networks.
-
Product
Serializer/Deserializers & Selector Muxes
-
Serializer/Deserializer muxes use both rising and falling edges of the clock to serialize the data from parallel inputs to serial output while demuxes deserialize the data from its serial input to parallel outputs. Selector muxes routes the differential inputs to either one or more of the desired outputs upon assertion of the appropriately selected port. Muxes can be used in various applications including High Data Rate Ethernet, Fiber Communication, Signal Routing and Broadband Test & Measurement Equipment.
-
Product
Active biconical Antennas
BicoLOG X Series
-
Only a single broadband test antenna for the complete frequency range from 20MHz up to 3GHz. Optimal for usage with spectrum analysers for EMC measurement. Active Antennas with high gain up to 41dBi.
-
Product
RF And Microwave Modules
-
Unlike specialized RF and microwave module product suppliers, Shengbo Technology has accumulated rich experience in designing and developing broadband microwave test products. As a sophisticated RF and microwave test system, a large number of high-performance RF and microwave modules are required for system integration. To this end, we have conducted in-depth research.
-
Product
Broadband
-
The UNH-IOL is the industry's leader in testing broadband systems and equipment. Working closely with service providers, equipment manufacturers, and the Broadband Forum, we have spent the last 15 years developing extensive testing coverage for DSL, GPON, TR-069, and IPv6. Our broadband testing can help ensure your products and services meet your customers' expectations with the highest quality possible.
-
Product
Antennas
-
Com-Power EMI / EMC broadband and tuned antennas cover the frequency range of 9 kHz - 40 GHz. Most electronic products are required meet the various international EMC regulatory standards before they are introduced to the market. Com-Power provides a wide range of EMI antennas and accessories. We also have the capabilities to assist you with custom EMC antennas for special applications to meet your exact needs.Contact us today to learn more about our EMC broadband test antennas.
-
Product
Optical & RF Switches
-
OPTELLENT is a provider of broadband test & measurement solutions for communications. OPTELLENT’s test and measurement solutions are designed to offer unprecedented low-cost of ownership and ease of use.
-
Product
Impedance Matching Pads
-
Surface mount and coaxial 50 Ohm / 75 Ohm impedance matching pads for CATV systems, broadband networks, test setups and more!
-
Product
Prototyping & Test Consulting Services Solutions
test
Don’t cut corners on the path to quality. We are experts in Design for Test (DFT), Design for Manufacturing (DFM), agile development, prototyping and standards/best practices in many industries. Speak to our prototyping and consulting services experts to ensure you make the right decisions and investments at the start of your project.
-
Product
Automotive Test Solutions
test
The testing and simulation systems from this division are used primarily in the automotive and automotive supplier industry. These are, for example, modular function-testing systems and diagnostic tools for automotive ECUs or bus communication systems for a wide variety of electronic components in automotive production. Electromechanical assemblies and entire car seats are also tested to ensure they function
-
Product
BSD (Test Diagnostics)
test
BSD Test Diagnostics software can be added to either developer or factory run-time systems to further improve the location of faults such as net bridges (short-circuits), open pins, open nets and even ''twisted'' connections that can occur within cable assemblies. BSD Test diagnostics reports faults in a verbose English language statement with pin level information included and can easily interpret multiple fault conditions.
-
Product
Semiconductors Testing
test
Our Testers support the production lines of variety of products such as 40/100 GBps Mux/DeMux, LNA, WiMAX RF Transceivers, Microwave & Millimeter Wave components. This high reliability products are being used in (a) Networking & Communications (b) Consumer Electronics (c) Military & Space
-
Product
Design for Testability (DFT Test)
test
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.
-
Product
Standardize Production Test Software For PCBAs And Electronic Devices
test
The vast majority of test project man-hours are spent on software development, so the choices that teams make in software tools and architecture have significant impact on deployment schedules. Standardizing software across a team or organization increases both efficiency and proficiency, lowering the risk of missed deadlines and improving test quality and reliability. Test software must:
-
Product
EFT Module for Teststand
test
The Electronics Functional Test (EFT) Module for TestStand provides out-of-the-box tools to speed up development of automated tests for electronic assemblies including PCBAs, subassemblies and final assemblies. Test engineers can develop, deploy and execute test sequences quickly and efficiently with minimal custom code development for a shorter time-to-solution.
-
Product
NI Real-Time Test Cell Reference System
778820-35
test
DIAdem Advanced with DAC Bundle, Perpetual License, Include 1 Year SSP
-
Product
Dielectric Material Test Fixture
16453A
Test Fixture
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
EMI Test System
TS9975
Test System
The R&S®TS9975 is the base system for conducted and radiated EMI measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for large equipment under test. Combinations of different applications or incremental expansion are easily possible.
-
Product
Generator/Analyzer for NFC/EMVCo Manufacturing Test
Micropross MP500 PT1-NFC
test
Support for ISO 14443 A/B, ISO 15693, MIFARE™, FeliCa™. Measurement correlation with NFC Forum and EMVCo certification test bench. Automated test executive with ready-to-run test sequences. Reader/Writer and Card Emulation modes, resonance frequency measurements supported on same antenna. Embedded analog measurements - LMA, field strength, S11, Q factor, waveform characteristics. Physical parameter/waveshape characteristic definition
-
Product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
Test Fixture
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
Product
EVSE Test Platform
Test Platform
To manage both the challenging high-power requirements of electric vehicle supply equipment and the market demand, it is crucial to rely on a test system that performs to your specs. The right system needs to combine the tools for reliable asset communication, microgrid management, effective protocol simulation and high-power testing. This EVSE platform combines the right energy regeneration equipment with 25+ years of test experience to deliver the results you need to meet conformance in the time you need it.
-
Product
PCIe 4.0 Test Platform
PXP-400A
Test Platform
The Teledyne LeCroy PXP-400A Test Platform provides a convenient means for testing PCIe 4.0 cards with a self-contained portable and powered passive backplane. The PXP-400A provides power required for both cards under test, and an interposer can be used for connection to a protocol analyzer.
-
Product
Regenerative Battery Pack Test System
17020E
Test System
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
Product
SSD Test Systems
MPT3000ES / MPT3000ES2
Test System
Using the same high-performance electronics and powerful software as all products in the MPT3000 family, the MPT3000ES and MPT3000ES2 engineering stations feature a small footprint configured to test up to eight SSDs in parallel. The system's small size and ability to plug into a standard AC outlet enable users to conduct program development and interactive device debugging in either office or lab settings.
