VME Backplanes
-
product
VME Master - DAQ and Detector Interface
VX1394
The VX1394 board features a radiation hard 4.8 Gbps SERDES ASIC, which, in connection to a rad-hard optical transceiver implements a newer generation optical links for many detector readout systems. The ASIC performs data transmission, trigger distribution and clock forwarding towards the front-end electronics in the crate.
-
product
Backplane Test System
402HV
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
product
Backplane Profiling & Inspection System
603d
A major problem in the backplane industry is detecting bent connector pin defects. The most difficult being when the pin bends underneath the shroud rather than going into the hole. Many times this defect cannot be detected electrically as the connector pin is touching the conductive annular ring of the hole, allowing electrical test to pass. Unfortunately, it is an intermittent connection and will fail later on as there is not an actual mechanical connection.
-
product
PCI Express Gen 3 Test Backplane
SKU-015-01-PCIe
PCI Express Backplane was designed to support a variety of modern PCI Express board’s production testing and debugging. The backplane expands the Host computer into four x16 PCI Express slots via 10 ft. CAT7 data and 10-pin flat Power control cables. PCI Express Backplane and UUTs (unit under test – add-in PCI Express board) are powered by a standard ATX power supply connected to the backplane via 24 and 8 pin power connectors located on the backplane.
-
product
6U VPX Power Backplanes
VPX is a broadly defined technology utilizing the latest in a variety of switch fabric technologies in 3U and 6U format blades. Open VPX is the architecture framework that defines system level VPX interoperability for multi-vendor, multi-module, integrated system environments.
-
product
Wiring Analyzers for Cables, Wire Harnesses, Backplanes
CableEye M2Z, M3Z, M4
Fast ● Simple ● Precise
Advanced wiring analyzer scans for continuity (opens, shorts), miswires, resistance, capacitance, components (resistors, diodes, LEDs, capacitors), insulation resistance, intermittent connections.
For diagnostic and Pass/Fail Testing
All CableEye® testers are suitable for production, fault diagnosis, QC (Quality Control), assembly, and prototyping of standard or custom cables. Each combines test, fault location, design, documentation, labeling, and database storage in one instrument. Tests can be performed on long cables (with or without connectors) or no cables (e.g. connectors, backplanes, PCBs, components).
Standard Features & Benefits:- USB certified, PC-based tester for a versatile, fast, robust system with long life-cycle.
- Multilingual, dynamic, graphic-rich display (netlist & wiring schematic) provides clarity and speeds diagnostics.
- 128 Test Points, expandable to 1024 providing flexibility as your product line changes.
- Real-time screening for intermittent connections for pinpointing elusive faults and improving quality.
- Automation scripting in a simple, intuitive language allowing non-programmers to reduce operator error by automating repetitive steps.
- Pop-Up Work Instructions. choose the exact amount of detail, imagery, language and automation you need to ensure your work instructions and tests are carried out flawlessly.
- Flexible tolerancing: optionally define as percentages or absolute terms, as well as asymmetrically (e.g. +0%/-10%) for improved yields.
- Barcode-tracking & archival data-logging to achieve error-proof test process and improved traceability & productivity.
- Print PASS/FAIL labels, test reports (with or without color wiring schematics/netlists) and log reports to satisfy ISO9000 reporting requirements.
- Compatible with laptop and touchscreen PCs for fieldwork and rack/off-bench mounting.
Includes:
CB15C board set (Item 745C) for common computer and peripheral device cables; comprehensive PC software with Database of >200 standard cables; 2 yr Product Support Subscription comprising Warranty, free tech support, and free software upgrades.
Select Add-On Options:
Hardware: 128-point Expansion Modules (attach to base); Environmental Sensor
Software: PinMap™ fixture editor, Connector Designer™ connector editor, or Autobuild™ guided assembly modules
camiresearch.com |@CAMI_CableEye |+1.978.266.2655 -
product
VME Radar Processing System
Signal Processor is Standard 19' rack mount chassis. 400 Hz, 3-phase, 115VAC aircraft power is available. Typical system can handle 200 MB/s (minimum) input data (also output data since we record the input data). Options include 10 GigE, Infiniband, FibreChannel or Serial FPDP. Optional 1GigEthernet for output products, parameter data, control messages, etc.
-
product
Passive Backplanes
Passive Backplanes series are easily customized which include PCI boards, ISA boards, PICMG 1.3 full-sized, PICMG 1.0 full-sized and half-sized single board computers. All backplane products provide with matching chassis and outstanding expansion flexibility.
-
product
PICMG 1.0 Full-Size SBC Backplanes
PICMG 1.0 Full-Size SBC Backplanes product line offer you low MTTR (Mean Time to Repair) approaches. The SBC backplanes are the most flexible and expansible solutions for industrial and slot-hungry applications.
-
product
2 Slot 6U VME 64x Backplane
DP-VME-7008
DP- VME-7008 is a 2 slot 6U VME 64x backplane designed to be used with VME boards. This module provides the interface and communication between 2 slot and the rear side mating for the rear boards.
-
product
6-slot ATX-supported PICMG Bus Passive Backplane
ATX6022/6
*1 PICMG, 4 PCI and 2 ISA*Compatible with AX60501 and AX60530*Supports both AT and ATX power supply
-
product
8-Channel VME LVDT/RVDT Scanner
V550
The V550 is a 6U, one-slot VME module which will acquire position data from up to eight LVDT (linear variable differential transformer) position sensors. The LVDT sensors are excited by an ultrastable synthesized sinewave generator, and conditioned by a precision 16-bit A/D converter followed by digital signal processing. The resident microprocessor supervises scanning and signal conditioning, and places updated position data in VME-accessible dual-ported data registers for instant access from the VME bus.
-
product
VME Extender
VME64-M
VECTOR Electronics and Technology, Inc.
Excellent performance with a multi layer design
-
product
VME Sequencer
SIS3100
The SIS3100 was developed as the VME side of our PCI to VME interface. The module is however perfectly suited for other custom applications like a histogramming multiscaler for LIDAR or a generic DSP controlled VME histogrammer .
-
product
Digital Backplanes
MSXB 034
Digital Backplanes provide expansion slots to accommodate compatible digital external boards. Digital Backplanes are passive, and connect all signals in each of the expansion slots in parallel. All expansion slots are identical.
-
product
Backplane
Axiomtek offers various kinds of backplanes for industrial computing platforms, including PICMG 1.0 PCI, PICMG 1.0 ISA, PICMG 1.3 full-size, and PICMG 1.3 half-size backplane. Axiomtek's backplane product line provides not only the highest compatibility with power supply unit but also the best choice of slot expansion.
-
product
VME SBC
XVR19 6U
The XVR19 provides straightforward, cost-effective and low risk upgrades for users of previous XVR products, bringing enhanced processor performance, enhanced storage and improved protection against obsolescence. They will also be attractive for new programs looking to benefit from Abaco’s established and proven VME roadmaps.
-
product
cPCI Serial Backplanes
CompactPCI Serial is an industrial standard for modular computer systems. It is based on the established PICMG 2.0 CompactPCI standard, which uses the parallel PCI bus for communication among a system's card components. In contrast to this, CompactPCI Serial uses only serial point-to-point connections.
-
product
VME Extender
VME64-M-5R
VECTOR Electronics and Technology, Inc.
Excellent performance with a multi layer design
-
product
PICMG 1.0 Half-Size SBC Backplane
PICMG 1.0 Half-size SBC Backplane designed with industry-standard ISA and PCI gold fingers for expansion. SBC Backplane equipped with fanless cooling and low-power configurations especially suitable for mid-range industrial applications.
-
product
FlexVPX Backplane
FlexVPX provides system designers with the flexibility and performance required for the most demanding applications. The ability to interconnect 2 and 3-slot 3U VPX compliant backplanes allows for custom system configurations using COTS hardware. Backplanes are equipped with PCI Express bridges that ensure fast and high-throughput for point-to-point communication between different elements in the system.
-
product
16-Channel VME Analog Output/Thermocouple Simulator Module
V470
The V470 is a 6U VME module that provides sixteen independent, isolated analog outputs that may be user-programmed to operate as voltage outputs or thermocouple simulators. Users may write temperature or voltage values at VMEbus speed, and the microprocessor will transparently do all necessary calculations and update the channel electronics.
-
product
13-slot ATX-supported PICMG1.3 Bus Passive Backplane
FAB114
The FAB114 has a PICMG 1.3 CPU card slot, one PCI Express x16 slot, three PCI Express x1 slots and a total of eight 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Through one PCIe x16 link, this PICMG 1.3 backplane maximize the performance of high-end PCI Express graphics and video cards. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB114 is perfect fit for AXIOMTEK's SHB100 and SHB110. AXIOMTEK also offers versatile 4U industrial chassis specially design for the FAB114, such as the AX61400, AX6156 series and AX61491.
-
product
VME Bus Analyzer / Exerciser
VME650
The VME650 Analyzer / Exerciser supports the latest VME bus specifications and protocols. From standard VME transfers to MBLT protocol.
-
product
VME PCI Express Crate Controller
V120
The V120 is a VME bus master crate controller, usable as a crate slot 0 arbiter or as a secondary controller. Each PCI Express cable driver board, in a PC backplane, can drive one to four V120s over standard, flexible PCI Express cable assemblies up to 7 meters long.
-
product
VME & CPC Systems
Verotec has a selection of configured systems plus individual elements such as backplanes, power supplies and cooling products, compliant with the PICMG / VITA specifications, and supported by a range of accessories. We offer these in standard VME and CompactPCI platforms across various mechanical form factors with customising options to suit specific applications.
-
product
6-Channel VME Pulse Amplifier
V860
The V860 is a multichannel pulse amplifier packaged as a standard VME module. It accepts logic-level inputs and generates high-level, very fast positive output pulses.
-
product
PCI/PCI Express Expansion Backplane
SKU-075-0X
PCI/PCI Express Expansion backplane was designed as a universal solution for Desktop or Laptop host computer expansion.It allows adding up to 4 PCI and up to 2 PCI Express boards to the host computer. Expansion backplane can be placed inside any general-purpose computer chassis and connects to the host computer via 5ft (or 10ft) CAT6 cable.
-
product
VME Type 32 with 6U, 5 slot Backplane
32V05MMX36N3V10
VME Type 32 with 6U, 5 slot Backplane J1, J2.





























