Wireless Test Fixtures
Typically use a PCB in lieu of wire to route IO connections between ATE interface and UUT connections.
-
Product
Mixed Signal, Multi-Functional Test Module
PXIe-ScanIO-112
Test Module
The PXIe-ScanIO-112 delivers a powerful combination of digital, analog, and AC-coupled testing in a single PXIe module. With 104 boundary-scan controllable digital I/O channels and 8 analog I/O channels ranging from –15V to +15V, engineers gain the flexibility to test a wide variety of board-level designs. The module supports IEEE-1149.6 AC-coupled interconnect testing, configurable single-ended and differential pin operation, and integrates seamlessly with the Corelis ScanExpress™ suite.
-
Product
Semicon Test Probes
-
Fine pitch, 0.20 mm [8 Mil] - single & double ended - non-rotating - kelvin - RF - high performance.
-
Product
Compact EMC Test System
Multi-CE5
-
The Multi-CE5 includes an Electrical Fast Transient Generator (EFTG), a Combination Wave Generator (CWG) and a Coupling-/Decoupling Network (CDN) for single-phase power supply lines. The software program CE-REMOTE allows full remote control of the test generator via Ethernet light guide as well as recording, evaluation and documentation of test results, according to IEC 17025. To record the wave shape of impulses, it is equipped with an Impulse Recording Function (IRF).
-
Product
Vibration Test Systems
G-5 Series
-
Both Shock tests at from relatively high acceleration(max. 4900m/s2 -500G) to low acceleration with wide pulse width, difficult to achieve with conventional Shock Test Systems and Vibration tests for not only IEC, MIL and JIS but also requiring higher acceleration, velocity and displacement than ordinary VTSs can be carried out with one system.
-
Product
Millimeter Wave Antenna Testing
-
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
Product
Test Services
-
INFRAMET offers two types of services in field of electro-optical imaging systems: 1)Trainining and consulting; 2)Test services.
-
Product
Water Quality Test Kits
-
The range of model shapes, sizes and capabilities of water quality test kits reflects the diversity of potential end users, who could just as easily work for a small laboratory as for a giant water treatment plant. The simplest water test kits are pocket-sized and measure only one water-quality parameter, such as pH or conductivity. A step above these water test kits are test kits able to measure multiple parameters, including total dissolved solids and dissolved oxygen. A bit higher up the price-performance curve are industrial-quality handheld water test kits that measure one or multiple parameters, and may even log the readings to enable trend analysis.
-
Product
Wireless Ethernet Bridges
-
Our wireless Ethernet bridges connect your wired devices to a wireless network - explore our range of advanced solutions.
-
Product
Gravity Test Handlers
-
Microtec offers a wide variation of customizable gravity handlers. The focus of our systems is based on the approach to provide 1 system for many different applications. By pursuing continuous improvements and setting the objective to provide our customers the most convincing test handlers, we are always driven to push our products and its features to the limits and exceed traditional boundaries.
-
Product
Power Supply Test System
-
The Procyon PTS 2100-10 is a configurable turnkey Power Test System, delivering automated test equipment (ATE) to some of the world’s largest-volume manufacturers as well as the affordability needed by niche market producers. Aerospace, defense, and avionics power supply ATE test systems applications include functional testing of AC and DC power supplies, generator, and engine control units, as well as a wide range of associated electronics.
-
Product
Xenon Test Chambers
-
Weice Testing Instrument Co.,Ltd.
Weice Xenon Test Chambers (Xenon Arc Test Chambers) are used to induce property changes associated with the effects of sunlight, moisture, and heat. The property changes include cracking, color fading and yellowing could be simulated just in few days and weeks.
-
Product
Thermal Testing
-
A view of multiple testing stations for use in conducting Thermal Analysis on various materials. This is one of several areas assigned to various thermal tests. Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), Thermomechanical Analysis (TMA), and Dynamic Mechanical Analysis (DMA)
-
Product
Test Manufacturing
-
Since forming in 1986, Amfax has always recognised the importance of having a strong manufacturing department in house, staffed by skilled qualified individuals.
-
-
Product
Analogue Concrete Test Hammer
181
-
The Elcometer 181 Analogue Concrete Test Hammer provides a quick, simple and inexpensive method for non-destructive evaluation of concrete compression strength and other masonry materials.
-
Product
Test Valva Score
AI
-
Test Value Score is a revolutionary AI-powered feature that dynamically assigns a score to each test according to the contribution it provides to the testing process. The Test Value Score allows Test Managers to optimize their testing operation under time constraints and budget limitations.
-
Product
Redox Flow Cell Testing
-
Specifically designed for use with our Redox Flow Cell Test System. All non-metallic flow paths are made with non-corrosive, chemically resistant plastics only!
-
Product
Intusoft Test Designer
-
Test Designer is today's only complete design simulation and verification system for analog, mixed-signal and mixed-systems design, which also features full fault and test synthesis capability. For the first time ever, engineers can efficiently design, simulate and test complex analog and mixed-signal circuitry in the design cycle
-
Product
Test Systems
-
6TL’s speciality is simplifying the architecture of test systems, so that our customer’s Total Cost Of Ownership is drastically minimized. The technology that conveys our mission is called FastATE.FastATE technology is based on using intelligent modules to build test systems.
-
Product
Circuit Breaker Test System
TDR9100
-
The Doble TDR9100 Circuit Breaker Analyzer is a state-of-the-art circuit breaker test set for testing all types of circuit breakers with efficient and accurate performance measurements.
-
Product
Tecap Automated Test Suite
-
Control of Automated Test Equipment (ATE) for functional test and in-circuit testOperation of test facilities with adapters and PLCssemi- and fully automatic testing of electronic components and assembliesFinal Test in ProductionTest of pre-series and sample seriesStandardized test program developmentAdaptable to your own system environment (customizing) – 100% usable after installation with standard elements
-
Product
Test Hardware
TTPSimulate XMC/PCIe
-
TTPSimulate is a high-performance test system which enables the simulation of a networked TTP system in real-time. It allows full hardware in the loop verification of a TTP unit. There are two form factors available for this product – PCIe and XMC card format. Both cards can act as four independent TTP nodes and have an IRIG-B interface for time-stamping.
-
Product
N Test Finger Nail
TF-24 series
-
Are designed to perform tests specified in many standards to determine compliance with safety requirements.
-
Product
Design for Test
-
Test Coach offers Design for Test (DFT) consulting to assist customers with design review of prototype boards prior to release for production. Design for Test analysis is extremely important in ensuring that an assembly will achieve the highest possible test coverage. For ICT, this DFT will review the board to confirm that the bed-of-nails test fixture can be fabricated to test an assembly without sacrificing test coverage. As with ICT, Flying Probe benefits from DFT analysis by reviewing test point access and mechanical challenges that may affect the potential test coverage. Completing a DFT enables Test Coach to make recommendations to our customers that may be implemented on boards during the design phase which will allow for the most comprehensive coverage at time of test.
-
Product
Meter Test & Calibration
-
Kongter Test & Measurement Co., Limited
Kongter offers a whole line of products for meter test and calibration including portable power source, standard reference meter and meter test system. All products are accredited to the highest production standards with different options of measurement accuracy (class 0.05 and class 0.1).These enable them to cover different applications for test and calibration of different types of energy meters, electric transducers, indicating meters and so on.
-
Product
Function Test Systems
-
These specialist Automeg models test the function and integrity of wiring harnesses combined with active components such as relays, switches, contactors, diodes, LEDS, actuators and other active components.Our software takes the complex and traditionally long task of creating functional tests away from the test engineer and allows these to be created automatically, from existing ECAD data and our component library and automated software routines. All the different routes and subtests are automatically calculated in seconds.
-
Product
ADI Test Fixture
TA-6500
-
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) type connector to minimize contact wear. The expanded localizer and nav input pins J2-34/35 are exposed on the panel to facilitate the insertion of a 200 ohm shunt when required. The fixtures rear panel has connectors for the required dual API/Synchro transmitter interface while the panel switches provide the correct routing of each.
-
Product
Package Testing
-
AMERICAN TESTING LABORATORY tests all types of product packaging, from shipping crates to child resistant packaging. In addition, we test the effects of many types of physical and environmental shocks on products inside the packaging.
-
Product
Universal Test Machine Stands
FTUS
-
Portable, adjustable height, stands are available for all FTU chamber models. They support the chamber without transferring weight to your testing machine. Standard Universal Test Machine stands are furnished with an 18 inch, electrically actuated, lift system, four swivel casters with locks, and an all welded frame. Four types of stands are available
-
Product
Protective Relay Test Set
POM2-6143
-
POM2 series protective relay test equipment is the best modular designed relay tester with local control system. There are 2 models, the POM2-6143 and POM2-3243, the POM2-6143 with 6×15A and 4×300V.
