References
A source of comparison.
See Also: Reference Standards, Reference Antennas, Reference Decoders, Reference Jumpers, Reference Sources, Reference Transformers, Reference Transmitters, Acoustical References, Frequency References, Solar Reference Cells
-
Product
2-Channel DAC FMC Module
FMC230 – HPC
-
Sundance Multiprocessor Technology Ltd.
The FMC230 is a dual channel DAC FMC with a very wide band. The two 14-bit D/A channels operate at 5.7Gsps (2.85Gsps direct RF synthesis) and are clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. The FMC230 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
Product
VXT PXIe Vector Transceiver
M9421A
Vector Signal Transceiver
Purpose-built for rapid solution creation and faster throughput in manufacturing test of wireless components, power amplifiers, and RF front-end modules Increase test density and reduce your footprint with up to four VXT instruments in one 18-slot chassis Reduce development time with open-source test libraries and reference solutions Start closer to your finish line with built-in FPGA-accelerated measurements Optimize test routines using proven software for noise figure and standard-specific measurements
-
Product
16-Channel ADC Module
FMC116
-
Sundance Multiprocessor Technology Ltd.
The FMC116 is a sixteen-channel ADC FMC Daughter Card which is fully compliant with the VITA 57.1-2008 standard. The FMC116 provides sixteen A/D 14-bit 125Msps channels which can be sampled by an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. A trigger input for customized sampling control is also available. The FMC116 has the HPC (high-pin count) connector, front panel I/O, and is conduction cooled capable.
-
Product
4-Channel 200 MHz A/D with 32-Channel DDC, Virtex-7 FPGA - XMC
Model 71762
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- Four 200 MHz 16-bit A/Ds- Four multiband DDCs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable serial gigabit interfaces- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Also available in 3U VPX, 3U & 6U cPCI & PCIe- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe- See comparable Jade Xilinx Kintex UltraScale FPGA Module: Model 71862
-
Product
Conventional Panel-mounted Type Power Amplifier Control Unit
PAT01
-
PAT01 is a power amplifier control unit that controls timing output and reference signal test source for power amplifier.
-
Product
VME Analog Output Module
DP-VME-2115
-
DP-VME-2115 is an industrial standard 24 channel D/A (Digital to Analog) board. It incorporates most of the features which are demanded in industrial applications. Each Digital to Analog Converter (DAC) is provided with a separate reference voltage selection either from internally generated reference or from the external input. This external input reference signal is passed into the protection circuits before it is fed to any active components. The input protection circuit is designed for ± 25Vp-p input ranges. The DAC output may be unipolar or bipolar and the output is jumper selectable, which is routed to the VME P2 connector, with short circuit protection of upto 30mA.
-
Product
Solar Cell I-V Characterization System
VS6821
-
Industrial Vision Technology Pte Ltd.
This system provides cell manufactures and laboratories a new way in testing and measuring photovoltaic cells. Integrated with Steady-State Solar Simulator, it provides complete coverage of testing parameters and measurement requirements by most international standards. Its test methods, procedure & equipment are IEC 60904 compliant. Calibration of reference cell is performed at Fraunhofer ISE in Germany, and is traceable to PTB.
-
Product
IRIG B to NTP/SNTP Converter
-
Signals & Systems India Private Limited
IRIG B TO NTP/SNTP CONVERTER – SPC-INS-1010 is a compact DIN rail mountable protocol converter unit which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using IRIG-B signal obtained from GPS receiver. It provides nanosecond accuracy when external time references are not available. It has the storage facility to store the system log file. It delivers NTP, SNTP, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through Web-based application. It supports a wide range of power supply input either 90V-260V AC/DC or 18-36VDC or 36V-72VDC.
-
Product
Humidity Detectors
-
A humidity detector, also referred to as a humidity meter or humidity gauge, is a device with a humidity sensor that measures the relative humidity in the air. PCE Instruments offers a number of humidity detector products including handheld humidity detector, data recording or data logging humidity detector, and combination or multifunction humidity detector devices that also measure parameters such as room or ambient temperature and atmospheric or barometric pressure. A humidity detector can measure relative humidity (RH) as a percentage (%) from 0 to 100 % RH, depending on the humidity measurement range of the specific model.Humidity is a key factor in everything from library and museum archival to agriculture, construction, manufacturing, transportation, warehousing, and heating, ventilation, air conditioning and refrigeration (HVACR). A relative humidity meter also is helpful in evaluating workers' heat stress risk on production floors and job sites. In addition, humidity plays an important role in the residential sector. If the humidity is too high in a private household, mold can grow. Mold creates a health hazard for anyone breathing the air in the home.
-
Product
Lake Variable Area Flow Meters
-
Lake Variable Area flow meters, often referred to as rotameters, measure flow rate of a liquid or gas by relating linear displacement of an internal “float” or sharp-edged orifice plate (Lake) to a corresponding flow rate. As flow rate increases, the orifice area that the flow moves through also increases – thus, the term “Variable Area.” Variable Area meters either allow flow through a peripheral orifice formed between a tapered wall and a float as in the traditional rotameter, or an annular orifice and an internal tapered metering pin in the Lake Monitor.
-
Product
FMC Dual ADC 12-bit 2.6 GSPS, Single DAC 16-bit 12 GSPS
FMC250
-
The FMC250 is an FPGA Mezzanine Card (FMC+) per VITA 57.4 specification. The board has dual ADC and single DAC. The FMC250 utilizes dual AD9625 ADCs providing 12-bit conversion rates of up to 2.6 GSPS and a single DAC (AD9162 or AD9164) providing 16-bit conversion rates of up to 12 GSPS. The analog input, digital output, clock and trigger interfaces of the FMC250 are routed via SSMC connectors. The internal clock frequency is programmable and the clock is capable of locking to an external reference.
-
Product
DC to LVDT and DC to RVDT Converters
-
Computer Conversions Corporation
The SLVT Series are complete, low profile, continuously updating, single channel, Isolated Digital to LVDT Converters used to simulate the output of LVDT's (Linear velocity displacement transducers), RVDT's (Rotary...) and other phase/voltage sensitive AC devices. They provide a very precise linear AC voltage output proportionate to the magnitude of the input data, in or out of phase respective of the AC reference input as determined by the MSB of the input word (offset binary format).
-
Product
Paramagnetic Oxygen Analyzer
Model T802
-
The Model T802 O2 uses the proven paramagnetic measurement principle, coupled with state of the art microprocessor technology, to provide accurate and dependable measurements of Percent-Level O2.Paramagnetic technology is non-depleting, which means that there are no consumable parts, and ensures a consistent performance over time. The selectivity of the paramagnetic measurement for oxygen means that there is little or no interference from other common background gases. The T802 offers a stable and inherently linear measurement of oxygen, making it possible to calibrate the analyzer by checking only two points. There is no requirement for a reference gas during operation.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T802 comes with the NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
Sound Level Indicators
-
A sound level meter is a measuring instrument used to assess noise or sound levels by measuring sound pressure. Often referred to as a sound pressure level (SPL) meter, decibel (dB) meter, noise meter or noise dosimeter, a sound level meter uses a microphone to capture sound. The sound is then evaluated within the sound level meter and acoustic measurement values are shown on the display of the sound level meter. The most common unit of acoustic measurement for sound is the decibel (dB); however, some sound level meter devices also determine the equivalent continuous sound level (Leq) and other acoustic parameters. With a portable sound level meter, industrial hygiene and workplace safety professionals can measure sound levels in multiple locations to ensure environmental conditions fall within recommended exposure limits (RELs). Some sound level meter devices can be permanently installed for continuous monitoring of sound levels at a work or job site.An important attribute to consider when searching for a suitable sound level meter is its type or class. The type or class of a sound level meter defines the device's accuracy as per American National Standards Institute (ANSI) or International Electrotechnical Commission (IEC) guidelines. Typically, "type" is the grade according to the ANSI S1.4 standard, whereas "class" is the grade according to the IEC 61672 standard. There are two types or classes assigned to sound level meters: type 1 / class 1 or type 2 / class 2. For assessing noise in basic industrial, commercial, educational, recreational or residential applications, a type 2 / class 2 sound level meter usually will suffice. For precision-grade assessments often made in a laboratory, a type 1 / class 1 sound level meter primarily is used. PCE sound level meter products are lightweight, easy-to-use and manufactured in accordance with the highest industrial standards.
-
Product
COM Express Type 10 Starter Kit Plus
COM Express Type 10 Starter Kit Plus
Software Development Kit
The COM Express Type 10 nanoX Starter Kit Plus consists of a COM Express Type 10 core module reference carrier board that provides two PCIe Mini Card slots, 2 RJ-45 LAN ports, 2x USB 3.0, 2x USB 2.0, 1x USB client, 2x DB-9 COM, 1x SD card socket, and Mic/Linein/ Line-out. ADLINK also provides additional development tools including a verified 10.1" LVDS panel (optional), power supply, thermal solution and cabling accessories.
-
Product
Balance Thermocouple Power Sensor, DC To 18 GHz
N8481S
Power Sensor
The Keysight N8480S Series Balance Thermocouple Power Sensors are intended to be used as measurement standards for RF power. They are suitable for use in a microcalorimeter-based primary measurement standard and as a secondary or reference measurement standard. The new balance thermocouple power sensors offer a broad frequency range DC up to 18/50 GHz, high maximum input power of +20dBm, fast measurement speed/settling time as well as ease of maintenance.
-
Product
Universal Clock
DXD-8
-
The DXD-8 Universal Clock, a precision multiformat reference generator generates up to 4 independent video syncs and audio clocks simultaneously. With the PTP option, it acts as a bridge between an IP infrastructure and legacy A/V equipment.
-
Product
Rad-Hard Analog ICs
-
ST's wide range of rad-hard QML-V qualified analog ICs covers analog-to-digital converters (ADC) and digital-to-analog converters (DAC) for telemetry, instrumentation and imaging applications. Our portfolio also includes rad-hard op amps, high-speed differential amplifiers up to 1 GHz, shunt voltage references and comparators to ensure a complete solution for signal conditioning, referencing and data conversion.
-
Product
2-Channel 500 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - 3U VPX
Model 52650
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Supports gigabit serial fabrics including PCI Express, Serial RapidIO and Xilinx Aurora- Two 500 MHz 12-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factors provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Programmable Voltage Reference Plug-In
ProDAQ 3202
-
The ProDAQ 3202 voltage reference card is used in the ProDAQ 3180 ultra-performance motherboards and LXI function card carriers. The ProDAQ 3202 voltage reference card is plugged directly onto the motherboard or carrier and can distribute the reference voltage to all ProDAQ function cards via two signal lines. This allows the distribution as a differential signal to overcome possible noise pick-up.
-
Product
Downconverter
DOWNCONVERTER 10 GHz VXI
-
The DOWNCONVERTER 10 GHz design assumes its use in closed mobile complexes for field testing of communications equipment. To do this, the device has applied advanced solutions to reduce the phase noise of the output signal in conditions of increased vibration and temperature. The device has a temperature-stabilized reference frequency generator with the ability to output a reference frequency signal. Also, it is possible to operate from an external reference generator.
-
Product
Power Meter
TW3211
-
Techwin(China) Industry Co., Ltd
TW3211 optical power meter Is a handheld optical power meter, newly released in 2007, which can be used for absolute optical power measurements as well as for relative loss measurements in optical fibers. A Ø1.0mm photosensitive area photodiode is used to significantly improve the stability and the reliability. It features ingenious appearance, a wide range of power measurement, high accuracy, an user self-calibration function and a reference power level storage.
-
Product
Anechoic Chamber room for Automotive components
-
Anechoic Chamber room of most suitable Automotive devices EMI/EMS test of the method of ALSE, which meet the global standard like a 2004/104/EC, several emmission standard like a CISPR25 which automotive manufacturers in EU/USA refer to, Immunity standard like a ISO11452 and others for the Automotive devices.
-
Product
CT/PT Test Set
PCT200Ai
-
PCT200Ai is the CT/PT test set (current transformer analyzer) that can finish various current transformer test of different CT and plus reference testing functions of PT. Compared with PCT200i, its accuracy is higher.
-
Product
1 GHz A/D and D/A with Virtex-6 FPGA - 6U VPX
Model 57630
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- One 1 GHz 12-bit A/D- One 1 GHz 16-bit D/A- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- Dual-µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Reference Grade Expandable Production Interface
Atlas
-
Atlas and Titan are world class multi-track interfaces offering flexible expansion and unsurpassable sonic clarity. Using the latest generation of Prism Sounds trusted conversion, Atlas provides more preamps than Titan making it suitable for a wider range of recording scenarios.
-
Product
Fluorescence Lifetime Systems
-
TCSPC, short for time-correlated single photon counting, refers to a powerful analysis method used especially in life sciences and fundamental physics. This technique is used to perform hyper-accurate fluorescence and phosphorescence lifetime measurements. As technology leader in equipment for multidimensional single photon counting, Becker & Hickl has been offering a wide range of high-efficiency TCSPC systems since 1993.
-
Product
Rack Mounted Spectrum Analyzer
-
Designed for the measurement and analysis of communications and broadcast carriers, making uplink, down- link, L-Band carriers, IF, and 10MHz reference signals easy to measure, monitor, and store.
-
Product
Power Integrity Analyzer Reference Solution
-
The power integrity analyzer reference solution is a hardware-based solution with the Keysight Infiniium S-Series 10-Bit ADC oscilloscope and probes, including the N7020A power rail probe that lets you see the true AC power noise on your DC power line and supports up to +/- 24 V offset and the N2820A high-sensitivity current probe that can measure down to 50 uA.
-
Product
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function PXI modules
PXI-2502
Multifunction I/O
ADLINIK PXI-2501 and PXI-2502 are high-speed, high-performance analog output multifunction PXI modules. These devices are able to update up to 8-CH, 12-bit analog outputs imultaneously sustaining 1 MS/s. The reference sources and output polarities are programmable individually per channel. Combine this with the multiplying PXI architecture, ADLINK PXI-2500 series PXI modules can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory. The PXI-2500 series integrate up to 8-CH, 400 kS/s, 14-bit single-ended analog inputs with programmable polarity, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
