Showing results: 391 - 405 of 585 items found.
-
CX-Z12 -
Shenzhen Chuangxin Instruments Co., Ltd.
The Finger Nail Probe is indicated to test IEC 60335 and UL requirements. Used to check the security of parts that snap together. The spring gauge assembled in the handle can be calibrated to the necessary force for using the instrument. This probe is made of stainless steel with appropriated hardened tip and a handle in insulating material. Handle has a special adaptor M5 for use with 50N force gauges.
-
EN62471-C -
Lisun Electronics Inc.
IEC62471-2006(CIE S009) Photobiological Safety of Lamps and Lamp System and IEC TR62471-2(2009) Guidance on Manufacturing Requirements Relating to Non-laser Optical Radiation Safety have be published addressing hazard to human (mostly eye and skin), and are completely suitable to assess the optical radiation safety of non-laser sources, such as LED products, UV radiation in general lighting products and etc.
-
VS6821 -
Industrial Vision Technology Pte Ltd.
This system provides cell manufactures and laboratories a new way in testing and measuring photovoltaic cells. Integrated with Steady-State Solar Simulator, it provides complete coverage of testing parameters and measurement requirements by most international standards. Its test methods, procedure & equipment are IEC 60904 compliant. Calibration of reference cell is performed at Fraunhofer ISE in Germany, and is traceable to PTB.
-
SKS-1206IA/SKS-1206IB -
Shanghai Sanki Electronic Industries Co., Ltd.
The ring wave generator is fully compliant with the new standards of IEC61000-4-12 and GB/T17626.12. The interface contains standard differences between IEC and Chinese national standards. Users can choose to enter the corresponding interface to perform different Test: Program -controlled high-voltage power supply and electronic switch have the characteristics of high precision, long life and good reproducibility.
-
Hilo Test
The ESD Simulators ESD suitable for performing EMC tests of systems and equipment according to the standards IEC / EN 61000-4-2 and ISO / TR 10605. It can far beyond the standard boundaries higher test levels are adjusted. Depending on the device under test and the test setup are two test method shall be: Air discharge (AIR) and contact discharge (CON).
-
Hangzhou Xun Anda Electrical Co., Ltd.
maximum capacity of the battery:200AH/2000CCA(SAE)Voltage test range: 1.5-15VDCWorking voltage 1.5-15VDC,powered by the tested batterMaxim Power Consumption: around 0.5WOperating temperature: -10°C~50°C Operating humidity: 30%~90%, without condensationdisplay modes: Four different colors LED indicatorbutton: 3 buttons.Test Standard: SAE,DIN,EN,IEC,CA.
-
WINDCUBE -
NRG Systems, Inc.
WINDCUBE is a remote sensing wind measurement device that uses pulsed Doppler Lidar technology to provide high quality data on par with an IEC calibrated met mast. Introduced to the market by LEOSPHERE, WINDCUBE has quickly become recognized as the market standard for superior performance for both wind resource assessment and wind farm performance monitoring. Lenders have readily adopted data provided by WINDCUBE and consider this device to be “best-in-class.” WINDCUBE is categorized as being in Stage 3 of DNV GL’s rigorous standards related to remote sensor acceptance for formal energy assessment purposes.
-
Smartech Inc.
• New extra-large display• Programmable button according to your needs• Water protected for heavy-duty work with coolants and lubricants, protection rating IP67 according to IEC 60529,• Automatic wake-up by moving the electronic on his frame. (Absolute System S.I.S)• Sleeping mode after 20 min. of no use. (Absolute System S.I.S)• Position memorized in sleeping mode, Absolute System S.I.S*• Maximum speed of displacement : 2.5 m/sec• Mechanical frame in stainless steel, hardened and grinded• Great comfort of use thanks to its ergonomic frame• Thumb wheel on request (see accessories)
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Rain test chambers for ingress protection testing simulates rain/water test as per IEC 60529 and DIN 40050-9((IP Code standard)) test standard. • IPX1 Protection against vertically dripping water• IPX2 Dripping water ± 15° from vertical• IPX3 Protection against spraying water• IPX4 Protection against splashing water• IPX5 Protection against low pressure jetting water• IPX6 Protection against high pressure jetting water• IPX7 Protection against temporary immersion• IPX8 Protection against continuous immersion• IPX9K Extremely high pressure jetting water
-
Kast Eng Co. LTD.
All electric equipments & systems is required Impulse Simulation Test to the to be tested under the condition where the power source is applied to the product-under-test.At this test condition, the decoupler is needed to reduce the impulse flowing through the power line while testing. And the coupler which is inserted between tester and product, to simulate the actual condition, so the electric circuit of decoupler is prescribet by IEC rules.
-
Castle Sonus GA116I -
Castle Group Ltd.
The Castle SONUS GA116I is a feature packed instrument that is fully compliant with IEC 61672-1:2002 Class 1, and IEC61252: 1993. This meter gives simultaneous Leq (rms. average) personal exposure (LEpd) and peak measurement for assessments to the Control of Noise at Work Regulations 2005. It has a high-specification, Class 1 measurement microphone and is cased in tough, crack resistant ABS plastic.
-
MPI-520S -
Sonel S.A.
The MPI-520S multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520S is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.
-
19055 -
Chroma Systems Solutions, Inc.
Hipot or dielectric withstand testing instruments manufactured by Chroma are used for conducting electrical safety tests on electrical components and products to make certain they are in compliance with IEC, UL, TUV, CSA, EN and other electrical safety requirements. In addition, these instruments are designed for general product or component testing as well as complex medical safety testing (60601-1) ensuring human safety and product reliability.
-
C.A 762 -
Chauvin Arnoux Metrix
The CA 762 Voltage Absence Tester is an essential tool for any electrician to check that no voltage is present before working on an electrical installation connected to the network. It complies with IEC 61243-3 Edition 3 and can be used to work on any indoor or outdoor 600 V CAT IV installation. To fulfil the requirements of the standards and legislation in certain countries, there are 2 references, with or without IP2X accessories.
-
C.A 742 -
Chauvin Arnoux Metrix
The C.A 742 Voltage Absence Tester is an essential tool for any electrician to check that no voltage is present before working on an electrical installation connected to the network. It complies with IEC 61243-3 Edition 3 and can be used to work on any indoor or outdoor 600 V CAT IV installation. To fulfil the requirements of the standards and legislation in certain countries, there are 2 references, with or without IP2X accessories.