-
product
Die Test Handler
3112
Chroma 3112 is a productive pick & place handler for high volume single- or multi-site bare die testing.
-
product
200KHz / 10000Freq.Point LCR Meter
MCH-2816A
It has high test frequency of 300kHz and 0.01Hz stepping arbitrary programming, and it has 10mV-2V signal level, all making it meet the precision test requirements of production line quality control, in-coming inspection and lab. Its HANDLER, RS232c interfaces are used for the component automatic sorting system, which provides the conditions for computer telecommunication and test recording. Flexible frequency-response analysis:Due to non-ideal inductor, capacitor and resistor, in order to preci...show more -
product
Gravity Test Handlers
Extremely small to very large packages, very wide temperature range, high throughput octal site and quad site testing.
-
product
Tri-Temp Octal Sites Handler
3160-C
Chroma 3160-C is a productive pick & place system for high volume multi-site IC testing.
-
product
50Hz-100kHz LCR Meter
11022/11025
Chroma Systems Solutions, Inc.
0.1% basic accuracyTransformer test parameters (11025), Turns Ratio, DCR, Mutual Inductance0Hz, 60Hz, 100Hz, 120Hz, 1kHz, 10kHz, 20kHz, 40kHz, 50kHz, 100kHz test frequencies21ms measurement time (≥100Hz)Agilent 4263B LCR Meter commands compatible4 different output resistance modes selectable for non-linear inductor and capacitor measuringHigh resolution in low impedance(0.01mΩ) and high accuracy 0.3% till 100mΩ rangeAdjustable DC bias current up to 200mA (constant 25Ω) (11025)1320 Bias Current S...show more -
product
IC Pick & Place Handlers
Chroma's IC test and handler solutions assure that IC packaging meets the original design specifications and verify the performance of the IC before it is assembled into the electronic product.
-
product
TestStation Automated Inline Handler | In-Circuit Test Solution
Teradyne’s High-Speed Inline Automated Board Handler with TestStation Multi-Site Test Insert is designed for productivity, fast change-over, and low operating cost. Our in-circuit test solution fits seamlessly into automated production lines to provide “hands-off-lights-out” operation.
-
product
Programmable Low-Ohm Meter
DU5210/5211
Delta United Instrument Co., Ltd.
20m ~ 2Mtest range, 0.1% accuracy Provided Level and Pulse measurement modes, can be lower temperature influence in Pulse Mode Provided HI/LOW limit and BIN Sorting comparator function, to meet your needed 100 sets of memory, can be saved test parameter and comparator setting, easy to use. Auto Calibration Program Function, to easier your calibration procedure. (Specificity calibrator needed) Cover up free, system firmware upgrade can be update via RS-232, easy to maintenance High speed FADC, ...show more -
product
PHOTO COUPLER TESTER
May be linked to machine handler for automatic test on production line.Test items include:VF、IR、Vceo、Iceo、Vsat、CTR
-
product
6TL60 Rotary Test Handler
H79006010
6TL60 has been designed according to the 6TL philosophy, following the concepts of flexibility, modularity and scalability, and with the aim of improving production efficiency as well as increase production capacity and reduce costs.The 6TL60 is the best production solution to automate test processes to reduce the cycle time and the footprint used in the manufacturing plan
-
product
Test Handler
M6242
Optimal Test Handler for Mass-Production DRAM, with Double the Throughput.
-
product
Automated Fiber Handler
1200
The 1200 Automated Fiber Handler is the first fiber preparation product that enables optical fiber manufacturers to significantly reduce the cost of production measurements by automating the critical optical fiber stripping, cleaning, cleaving and temporary coupling processes.
-
product
Slip Line Detection System
YIS 200
The YIS and SF Series metrology systems are designed for optical detection of wafer defects such as crystaldislocations, slip and other defects. The YIS-300HM (for 300 mm wafers) and YIS-200HM (for 200 mm wafers) utilizeMakyoh optics technology (Magic Mirror) and integrated robotic wafer handler provided by Hologenix.
-
product
ATOM Handler
The ATOM-IC Handler is a benchtop handler designed for use on engineering test floors and in development operations. Its innovative design allows for maximum flexibility and minimum cost and maintenance.
-
product
Component Test Systems
These products include test peripherals used with test systems, such as interfaces that connect semiconductor devices with test systems, and handlers that transport semiconductors to the test system. System-level test equipment and software are also included in this category.
-
product
Power Discrete Tester
Mostrak-2
M2 test system has multiple test generators which cover static and dynamic test procedures. It is our first truly modular tester which allows for the system to be upgraded and expanded when needed. M2 are designed to get the tester as close as possible to the handler interface and operator at the highest possible speeds. M2 is capable of HV (3 kV) and LV (600A) testing and has dynamic switching capabilities up to 1200V. MOSTRAK systems can test the following device types: MOSFET, IGBT, Bipolar transistor, Diode - rectifiers, Thyristor (SCR) - Triac, Linear voltage regulator (VReg), Transient voltage suppressor (TVS).
-
product
Final Test Manipulators
for test heads up to 250 kg / 550 lbsfinal test dedicatedhandler docking prolowest possible floor loadeasy motion in z-direction to facilitate docking processforce feedback control feature ensuring operator safety and protecting equipment during set-upactive cable managementdurable and robust designoptimized footprint for various test heads580 mm linear in/out motion for handler service access160 mm linear side-to-side feature270 column pivoting featurenumerous additional, unique features for individual set-up requirements
-
product
Single- and Dual-Yaw Axis Wafer Transport Robot
GPR-GB7SY
The GPR-GB7SY Yaw-Axis (single and dual yaw) robot features Genmark’s technologically advanced mechanisms including patented GPR and YAW technologies to achieve the highest level of performance currently available in an automated material handler capable of transporting up to 450mm wafer payloads with utmost reliability and precision.
-
product
Octal Test Site Handler
3180
The Chroma 3180 is a productive pick & place system for high-volume multi-site IC testing.
-
product
Test Handlers
Cohu has 50+ years of semiconductor test expertise designing and manufacturing pick-and-place, gravity feed, test-in-strip handlers, MEMS test cells, and turret-based test handling and back-end finishing equipment for ICs, LEDs and discrete components.Our test handlers support a variety of package sizes and device types, including automotive, mobile, power, micro-electromechanical systems (MEMS) and microcontrollers, among others.
-
product
LCR Digital Bridge
FD2810B
• Test parameter: C, R, L, Z, D, Q• Test frequency: 100Hz, 120Hz, 1kHz, 10kHz• Test level range: 0.1V, 0.3V, 1.0V• Output impedance: 30Ω, 100Ω• Slow or fast (15 times/s)• Automatic selecting, out of limit alarming• Provide the RS-232 & HANDLER interface• Accuracy: 0.1%
-
product
6TL36 Plus In-line Test Handler w/Bypass
EA923
- Test handler 6TL36 Plus.- Dual line (bypass)- 1096 x 1875 x 1851mm [WxDxH]- Expandable to form a group with several 6TL36 modules (adapt line to production volumes).- ICT, FCT with RF, ISP or Combined test (ICT+FCT)- Servocontrolled DUT stop (stopper-less system)- Exchange time 3,2s- Max. PCB dimension 600x450mm- 19” rack space for instruments integration: 28UH- Receiver 25 slots in probe plate + 4 slots in push plate- Automatic Conveyor width adjustment- Optional Return Conveyor- High dynamics conveyors (1500 mm/s)- 90mm Top-30mm Bottom Component clearance- SMEMA and Hermes standard- CE
-
product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
product
In-Line Functional Test Fixtures
Add an advantage to in-line production with fast change over interchangeable fixturing. Circuit Check’s in-line board handlers and in-line board handler fixturing exceed the high performance requirements associated with high-volume production. Circuit Check supports in-line fixturing for all the leading handlers.
-
product
Package Test Loadboards/DIB
DTS Package Test (DIB) loadboards are designed to specific devices and configured for both hand test and fully automated handler applications. DTS loadboards incorporate any brand of socket or contactor and can be configured for multi-site testing. Designs incorporate all necessary components, connectors, mechanical hardware and stiffeners to provide a complete plug-n-play solution. DTS has a vast database of tester and handler information which allow designs to be started and completed quickly without burdening the customer to supply excessive information. DTS designers are experienced in all device types, including digital, analog, mixed signal and RF devices.
-
product
Automated Lead Frame Testing
Sigma MAG
The Sigma MAG comes with an independent lead frame (un)loader for hands-free bond testing. The magazine handler is compatible with OHT and AGV and allows top and front-loading of multiple types
-
product
ULTRA® Contactors
ULTRA CONTACT Series offers high yield, durability and consistent performance under the most demanding testing environment. Our design offers easy integration to most test handler platforms and on automotive devices.
-
product
Modular Gravity Handler For Small Devices
Rasco SO2000
Modular designed gravity handler with various input and output possibilities. SO2000 can handle the smallest possible packages for gravity and provides a broad range of Sensor and MEMS applications.