TTL
Transistor–transistor logic.
-
Product
High Impedance Differential Clock Divider
-
Alliance Support Partners, Inc.
he ASP-DCD-00 board is a high impedance input clock divider circuit. It is designed to provide minimum load to a clock source for frequency measurement. It accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms; it divides the input signal frequency from 2 to 256 times depending on shunt jumper selections on J3. The board requires 5VDC 500mA power source to operate. The output is capable of driving 5V TTL logic levels.
-
Product
Low Noise Dual Band VCO
-
This custom oscillator subassembly consists of two low noise oscillators covering 1.5 to 2.5 GHz, a power combiner, a standard Teledyne RF & Microwave amplifier, and a lowpass microstrip filter. Teledyne RF & Microwave designed both oscillators for low phase noise and linear tuning. The output frequency bands are switched using standard TTL control.
-
Product
Industrial Controller
-
Industrial Controllers are high-performance, fanless controllers that provide connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. Controllers also have onboard isolated, transistor‐transistor logic (TTL), and differential digital I/O. You can use LabVIEW system design software to create, debug, and deploy logic to both the onboard FPGA and the processor. LabVIEW contains over 950 signal processing, analysis, control, and mathematics functions to accelerate development.
-
Product
Dynamically Controlled, High Speed Digital I/O PXI Express Card
GX5292e
-
The GX5292e is a high performance, cost-effective 3U PXI Express dynamic digital I/O boards offering 32 TTL or LVDS input or output channels with dynamic direction control. The GX5292e also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 100 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
Digital I/O
-
ADLINK digital I/O cards feature TTL I/O, isolated I/O, relay output, and timer/counter, and supports up to 256-CH high-density on a single board, making them suitable for I/O status monitoring and ON/OFF control applications.
-
Product
Amplifier, Switch and Test Box
CLIOQC Model V
-
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
-
Product
sbRIO-9403, Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
780539-01
-
Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The sbRIO‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the sbRIO‑9403 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and other applications.
-
Product
GPIB to Relay Minibox™
Model 4864
-
* Model 4864-11 provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Optional 1 'U' high Rack Mounting Kits hold one or two 4864s.* Includes 50-pin mating connector for solder connections.* Optional 1 'U' high Rack Mounting Kits hold one or two 4864s.* Optional terminal board and terminal strip for easy connections without soldering. See the GPIB Accessory page. * Model 4864-12 provides 16 heavy duty form A contacts (SPST).* All other specifications are the same as listed for the 4864-11. * Model 4864-14 provides 16 Relay driver outputs that sink 300 mA.* All other specifications are the same as listed for the 4864-11.
-
Product
4-CH Analog Output Module
ND-6024
-
- Channels: 4- Voltage Output: -10 V to 10 V- Output Isolation: 5000 VRMS- Resolution: 12-bit resolution- Accuracy: ± 0.02% of FSR- 7 TTL digital input
-
Product
4 Channel DAC FMC Module
DACNF04 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-DACNF04 is a four channel Digital to Analog converter FMC which complies with VITA 57.1-2010. Each channel provides 16-bit input and one DC coupled single-end analog output with DC – 250KHz sampling speed based on Linear Technology’s LTC2704-16. The 16-bit input data for each channel is provided through SPI from the FPGA on the FMC carrier board. A single-ended TTL level trigger output is provided from the FPGA.
-
Product
PXI-6508, 96-Channel, 5 V TTL/CMOS, 2.5 mA PXI Digital I/O Module
777598-01
-
96-Channel, 5 V TTL/CMOS, 2.5 mA PXI Digital I/O Module—The PXI‑6508 uses four, 24‑bit programmable peripheral interfaces (PPIs) that can each be divided into three, 8‑bit ports. The PXI‑6508 can interface to peripherals or other computers, and it can operate in either a unidirectional or bidirectional mode and handshake with peripheral equipment. The PXI‑6508 is well suited for applications that require onboard pull-up resistors.
-
-
Product
Light Source
pE-300ultra
-
CoolLED's pE-300ultrais a fluorescence microscopy light source which offers intense, broad-spectrum LED illumination for imaging most common fluorescent stains. Users have access to both microsecond switching via multiple TTL inputs and the ability to mount inline excitation filters. This, when paired with today's high performance multi band filter sets, facilitates imaging traditionally done via a white light source and a filter wheel, with all the benefits of LED.
-
Product
Electronic DC Load, 80V, 80A, 400W With/without Remote Interfaces
LD400 Series
-
Versatile solution for testing dc power sourcesConstant current, resistance, conductance, voltage and power modesWide voltage and current range, 0 to 80V and 0 to 80A400 watts continuous dissipation at 28°C (360W at 40°C)600 watts short-term dissipation (up to 60 seconds)Low minimum operating voltage of <1V at 40AHigh resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminals (front terminals 30A max.)Full bus control via USB, RS232 and LXI compliant LAN interfaces (LD400P)GPIB option (LD400P only)
-
Product
Synchro to BCD and Resolver to BCD Converters
TSBC TRBC
-
Computer Conversions Corporation
The TSB Series are miniature, high performance, continuous tracking, synchro or resolver to digital (BCD) converters and angle indicators employing a type 2 servo loop, designed for military and industrial control applications. They will accept any 3 wire synchro or 4 wire resolver input over a frequency range of 50 to 1200Hz. and convert it into 0 to 359.9 degrees or +/-179.9 degrees, TTL compatible BCD data.
-
Product
Pulsed And CW EPR/ESR: Synthesizers Up To 280 GHz
-
Insight Product Company offers synthesizers at frequencies from 30 to 280 GHz which can be used in EPR/ ESR experiments. These sythnesizers are designed to go swiftly from the generation to the non-generation mode and back. This process is controlled by external TTL signal. There is also the possibility to manipulate the phase, namely to shift it by 90 degrees and 180 degrees. ON/OFF switch time is approximately 2 nanoseconds.
-
Product
Dual Channel Tri-Level Driver Card
40465
-
Two channels of 10MHz drivers, that can be operated as standard Two-Level Drivers or operated as two channels of Tri-Level Drivers. In the Two-Level mode, the input to each driver channel requires one channel of TTL level timing. Tri-and four level modes require a second clock input. In the Tri-Level Mode, the output from lowest rail to high rail can be 18.5V. Like the 40460 the rise and fall time as well as the high and low voltage levels of each channel is programmable.
-
Product
PXI-6541, 50 MHz, 32-Channel PXI Digital Waveform Instrument
778952-02
-
50 MHz, 32-Channel PXI Digital Waveform Instrument—The PXI‑6541 is a digital waveform generator and analyzer for interfacing with 32 single-ended digital pins. The PXI‑6541 can sample digital waveforms at up to 50 MHz and interface with common transistor‑to‑transistor logic (TTL) voltage levels. The PXI‑6541 also features advanced synchronization capabilities for building integrated mixed-signal test systems.
-
Product
Pattern Generator
-
AVLINK TECHNIC TAIWAN CO., LTD.
* Intelligent functionality. * With 162 MHz pixel frequency. * Support total 38 timings. (up to UXGA) * Support Sync Type: H/V (TTL), SOG. * Low cost. * Single interface easily use. * Portable design, working time up to 8 hours by inside Re-chargeable battery. * Auto Power-off on Battery mode. * Provide total 34 patterns, Include: Color bar, Gray, Grid, Block¡K * By 16x2 Character LCD and key buttons, easily control.
-
Product
PXI/PXIe Trigger-Module
PXT(e)1741
-
Easy linkage of various external modules to the PXI(e) trigger busHigh configurable trigger matrix12 independent configurable trigger linesInputs/Outputs compatible with 5 V TTL standardSoftware controlled triggering of any target device
-
Product
Bi-Phase Modulators
-
PMI's line of Bi-Phase Modulators includes a comprehensive selection of different models which cover broad octave frequency bands ranging from 0.5 to 40 GHz. Bi-phase modulators take a TTL level digital bits stream that’s encoded onto the RF carrier using 2 Phase Shift Keying (2PSK) modulation, where the 2 phases are separated by 180º. This performance is desirable in communications systems, microwave radio, radar, high data rate test & measurement, serial data transmission, base station infrastructure, and other industrial and military applications.
-
Product
IC-3173, 2.20 GHz Intel Core i7 Dual-Core Processor, 4-GigE Port, 2-USB 3.0 Port Industrial Controller
785270-01
-
The IC‑3173 is a high-performance, fanless industrial controller for developers who require a high level of processing power and connectivity for automation and control applications in extreme environments. The IC‑3173 provides connectivity for communication and synchronization to EtherCAT and Ethernet CompactRIO chassis, EtherCAT motion drives, GigE Vision and USB3 Vision cameras, and other automation equipment. In addition, this controller has onboard isolated, TTL, and differential digital I/O, so it can perform synchronization and control tasks without additional tethered I/O.
-
Product
NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
779351-01
-
5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
Product
Switch
-
Chengdu KeyLink Microwave Technology Co., Ltd.
The power supply voltage of the series products are ±5V ± 5%，which using TTL control(default “0”：ON；"1"：OFF.).The frequency range covered by 0.5GHz~40GHz.The products have the characteristics of small size, high reliability, low insertion loss and high isolation.The products are applied to all kinds of receiving and transmitting channels. KeyLink's switches can be categorized as follows.
-
Product
Digital Control Step Attenuator
-
Digital control attenuators with TTL parallel control offering fast switching speed and high attenuation accuracy
-
Product
Broadband Amplified Noise Modules
NC2000/4000 Series
-
The NC2000 Series amplified noise modules are an excellent choice for high-level noise modules mounted on a circuit board. The NC2000 Series modules are housed in 24, or14-pin dual-inline packages. The NC4000 series modules are housed in a 40-pin module that cover similar noise bands to the NC2000, but have higher crest factor, and 60 dB of TTL controlled attenuation.
-
Product
DFM (Deep and Fast Modulated) generators up to 280 GHz
-
Insight Product Company offers DFM (Deep and Fast Modulated) mm-wave sources at frequencies from 30 to 280 GHz. DFM generators are designed to go swiftly from the generation to the non-generation mode and back. This process controlled by the external TTL signal. ON/OFF switch time is approximately 2 nanoseconds.
-
Product
PXIe-6545, 200 MHz, 32-Channel PXI Digital Waveform Instrument
780993-03
-
200 MHz, 32-Channel PXI Digital Waveform Instrument—The PXIe‑6545 is a digital waveform generator and analyzer for interfacing with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 200 MHz and interfacing with common transistor‑to‑transistor logic (TTL) voltage levels. The PXI‑6545 also features advanced synchronization capabilities for building integrated mixed-signal test systems and per-bank digital timing features.
-
Product
300-Watt AC/DC Power Supply
Model 56RS1
-
NAI’s 56RS1 is a 300 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides a single full-power output at a baseplate temperature of +85° C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
Product
LCM Tester
Model 27012
-
To meet the high accuracy and low price requirements for LCM TV test device, Chroma 27012 that integrates the signal and power source provide a complete test solution for LCD Module. Its LVDS, TTL (Option) signal source fully complies with the digital signal standard, meanwhile with the 24V, 12V, 5V, 3.3V DC source output it is able to supply power to VDD, Backlight for LCM test without obtaining external power source. Equipped with the interface of single key to switch the Timing, Pattern and Program rapidly for test in auto or manual mode, the 27012 is able to provide a direct and convenient test environment for LCM TV by its complete hardware configuration and easy operation.
