Interfaces
connections between dissimilar environments.
See Also: Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, Interconnects
-
product
Two Way Monitoring and Control
The Drexelbrook 560 DRX Series wireless products feature 900KHz frequency hopping, spread spectrum technology to provide a reliable, license free, wireless link between the field instrument and the control room.These wireless interface products provide a cost effective alternative to expensive hard wired connections.Using Frequency Hopping Spread Spectrum (FHSS) technology, a robust signal is provided that is virtually free from disruption due to interference.
-
product
IRD
SFT3975C
Hangzhou Softel Optic Co., Ltd.
SFT3975C HD IRD is SOFTEL’s new product which can receive signals from tuners (DVB-C, DVB-T/T2, DVB-S/S2/S2X, ATSC-T, ISDBT optional), ASI and IP. After demodulating, de-scrambling, re-multiplexing and decoding, it gives content out through various video/audio interfaces (HDMI, CVBS, 3G-SDI) or ASI or IP. This IRD is featured with two CAM/CI slots and BISS which supports to descramble encrypted Tuner, ASI or IP signals.
-
product
IP Gateway
SFT3503A
Hangzhou Softel Optic Co., Ltd.
SFT3503A Bidirectional IP Gateway is a head-end interface device which is used for DVB and Ethernet. It can be used both for a receiver and a lancers! On one hand, in the lancers part, this machine can be used for sending IP stream, turning the TS stream into IP Stream. On the other hand, in the receive part; this machine can be used for receiving IP stream, turning the IP stream into TS stream.
-
product
PC/104 OneBank Board
EMC2-ZU4EV
Sundance Multiprocessor Technology Ltd.
The EMC²-ZU4EV is a PCIe/104 OneBank™ SBC with a Xilinx Zynq SoC and a VITA57.1 FMC™ LPC I/O board. The main processing power of the EMC²-ZU4EV is a Dual Core ARM9 and combined with traditional FPGA fabrics/gates + High-Speed I/O interfaces, like USB2.0, HDMI, 1Gb Ethernet and SATA and provide an total solution for any Embedded Application.
-
product
Milliohm Meter
16502
Chroma Systems Solutions, Inc.
Basic accuracy : 0.05%Pulsed test current output mode is used to reduce thermal EMFs affection on milliohm measurementDC test current output mode is used to fasten measurement speed for inductive DUTDry-circuit test current output mode (limited Max. 20mV) is used to measure such contact resistances where the maximum open-circuit voltage must be limited to 50mVTemperature correction (TC function) regardless of material or temperatureUseful temperature conversion function for motor/ coil evaluatio...show more -
product
ColdFusion Switches
Chassis can be populated with any combination of Interface Blades making it the only L1 switch to support 10m to 128G in the same chassis.
-
product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-K
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
product
Datalogger IO-Expander
IOX-370
The I/O Expander takes as a central component of Immission measuring station the calculation of averages, controlling function controls and saving data. The raw data are analog, serial or read in via Ethernet. Automatically when certain events occur, a message by SMS or e-mail will be sent. The transmission of measurement data in the control center is via a modem or network. For configuration and visualization software IOVIS Lite is included. Furthermore, the stored values can requested with the integrated Web interface from any browser.
-
product
USB Type B Test Connector
Test connector for USB Type B (4 pole) for contacting USB interfaces. Application in USB devices like hard disks, data carriers, power supplies, etc.
-
product
Remote Radio Head Test, Reference Solution
The Remote Radio Head Test, Reference Solution provides the physical interfaces together with the vector signal analysis and vector signal generation you need to carry out comprehensive functional and performance testing of your RRH). Fully characterize the uplink and downlink, RF air-interface to and from the digital "front-haul".
-
product
Fibre Channel Modules
AIM’s Fibre Channel test, simulation and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with one dual core RISC processor per port, massive and scalable DDR3 memory and IRIG-B time encoder/decoder functions are standard. The new ultra high performance intelligent 4-lane PCIe 2.0 interface modules offer 2 ports with full function...show more -
product
PXI High Density MUX BRIC, 20-Chan, 40-Pole
40-570-215
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow tes...show more -
product
IP QAM
SFT3332 (-D)
Hangzhou Softel Optic Co., Ltd.
SFT3332 (-D) IP QAM modulator is Mux-scrambling-modulating all-in-one device developed by SOFTEL. It has 32 multiplexing channels, 32 scrambling channels and 32 QAM (DVB-C) modulating channels, and supports maximum 1024 IP input through the GE port and 32 non-adjacent carriers (50MHz~960MHz) output through the RF output interface. The device is characterized with dual RF output ports which broaden the bandwidth for QAM carriers.
-
product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequ...show more -
product
PMC ARINC 429 Board
MS 1723
- Bus Interface:- 32 Bit PCI Bus with PMC Interface- Speed of operation up to 66MHz- Spartan-3AN FPGA and Arinc429 controller based design- 8 transmit and 8 receive independent channels- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
product
PCI Express Mini Card
mPCIe-UCAN2 & mPCIe-UCAN2-ISO
The mPCIe-UCAN2 card features two CAN ports that instantly install in most any operating system as standard COM/ttyS devices. Each port supports CAN2.0 A/B and FD operations including data rates up to 10Mbps and timestamps with 1μs (or 1ms) resolution. These CAN ports can be controlled using a simple ASCII command/response interface using a superset of the popular CAN232 standard (extendedto support CAN FD requirements)
-
product
ISSRs for Mounting on Printed Circuit Boards
Series LS10
Series LS10 DC solid-state relays are designed for mounting on printed circuit boards. They facilitate heat-sinking by providing an interface surface. They can switch loads with high starting currents. The nominal switched currents depend on the size of the heat sink These relays use a direct-bonded copper substrate for thermal efficiency and long life.Available options include:LS60DC10C-21 10A, 7-36 Vdc Load; 3-10 Vdc ControlLS60DC10F-21 10A, 7-36 Vdc Load; 7-30 Vdc Control
-
product
GPIB ANSI X3.28 Interface
Model 4894B-7
ICS's GPIB to ANSI X3.28 Interfaces adapt older devices that use the ANSI X3.28 devices to the GPIB Bus. All ICS GPIB Interfaces are IEEE-488.2 compliant and HP-IB compatible.
-
product
Video Pulse Generator
MS 1811
*4 Channels of Variable Pulse / Amplitude Output*Pulse Generation Delay between any Two Channels can be Programmable between 2ns to 1ms*Pulse Width can be programmed from 20ns to 268ms (Range: 60ns � 2Sec, Resolution: 2ns, Accuracy: �5ns)*Programmable Pulse PRI (Range: 0ns � 2Sec, Resolution: 10ns, Accuracy: �5ns)*Delay Amongst Channels (Range: 0 � 1.34S, Resolution: 2ns, Accuracy: �5ns)*Rise Time and Fall time is less than 5ns (Programmable Slew Rate 2ns to 10ns � Optional)*Pulse Amplitude can ...show more -
product
USB Digital Storage Oscilloscope, 1GS/s, 200MHz BW, 10K/channel
Acute TS2202E
*PC-based (USB2.0 interface)*USB powered*2 channels (stackable up to 12 channels)*1 GS/s real-time sampling*200 MHz bandwidth*10K (TS2202)/64M (TS2212) points per channel*Vertical offset adjustable
-
product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends, 2m HV, Exit Towards Pin 1
A050DF5-T-HA200
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Ultrasonic Flaw Detector
MFD660C
MFD660C intelligent digital ultrasonic flaw detector, Mitech concentrated years meticulously developed premium product, has a lot of advantages like unique design, sophisticated manufacturing, convenient operation, powerful function. It had received customers' favored since its inception. It can test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in workpiece’s interior swiftly and accurately without any destruction. With full digital 640X480 TFT LCD di...show more -
product
EBIRST 8-pin Male Power D-type Termination Fixture
93-012-103
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
GPIB Digital Interfaces
All of ICS's GPIB Digital Interfaces are user configurable and let you transfer data as bits, bytes or as strings of bytes. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard and are HP-IB compatible.
-
product
Qseven® Reference Carrier Board
Q7-BASE
Qseven is a Computer-on-Module (COM) standard for small sized and highly integrated systems adopted by SGET. The Qseven concept is an off-the-shelf, multi-vendor, Computer-on-Module that integrates all the core components of a common PC and is mounted onto an application specific carrier board. Qseven modules have a standardized form factor of 70 mm x 70 mm or 40 mm x 70 mm and have specified pinouts based on the high-speed MXM connector, regardless of the vendor. The Qseven module provides the ...show more -
product
50 Ohm BNC to BNC Cable Assembly
40-977-501-2m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Digital Multimeter
M3511A
The M3510A and M3511A 6 1/2 Digits Multimeters are the newest generation of DMMs from Picotest. These new DMMs offer compact size, light weight, fast measurement speed & throughput, expanded measurement functions, systematization capability and highly usable interfaces including a standard USB interface and an optional GPIB/RS-232 interface. The M3510A and M3511A DMMs are suitable for both production and research/development use.
-
product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m, HV
A037DF4-C-HA050
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
sbRIO-9401, Non-Enclosed, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
782400-01
Non-Enclosed, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The sbRIO‑9401 is a configurable digital I/O interface for input or output in 4-bit increments. Therefore, the sbRIO‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the sbRIO‑9401 for implementing custom, high-speed counter/timers; dig...show more -
product
PCI To PCI Express Board
MS 1718
PCI to PCI Express card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit PCI signals from/to the Host System. These PCI signals are converted into PCI Express using PCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.