Optical Combs
Frequency comb measuring light frequencies.
-
Product
Germanium Optical Power Head
81623C
Optical Power Sensor
The new 81623C optical power head provides a 5 mm detector area and allows flexible placement of the remote optical power meter, which is then connected to the N7749C. The 81623C accepts parallel beams with up to 4 mm diameter, standard SM fiber and MM fiber with max. 100 μm core diameter, NA ≤ 0.3. A wide choice of adapters allows input from popular fiber connector types, bare fibers or open beams. The magnetic D-shaped adapters allow rapid removal and replacement without twisting attached fibers.
-
Product
Comb Generator
CG 50/500
-
The main application of Conducted Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble conducted measurements using an ISN.reference signal source Noise Generators Signal Generators
-
Product
Reference Radiators / Comb Generators
-
The Spectrum Generator is a family member of the Schwarzbeck pulse generators, which are used as pulsestandard world wide. Whilst the latter one uses a bounce free relay contact to discharge a coaxial lineto the load resistor, it uses a special avalanche transistor instead of the relay contact.
-
Product
Erbium Fiber Frequency Comb
-
Detailed description of item: The AOSense frequency comb is a low noise, polarization maintaining (PM) device. Key features include a PM fiber architecture centered at 1550nm with turnkey modelocking; a free-running linewidth of the carrier-envelope offset frequency of <200 kHz; a temperature-insensitive all-fiber f-2f interferometer exhibiting fceo beatnotes with SNR > 45dB (300kHz RBW); and dual fast/slow cavity length actuators with a bandwidth of >300 kHz. The repetition rate of the comb is factory set and allows matching across multiple combs for dual comb applications. The optics package incorporates an optical heterodyne module designed for locking to the comb to an ITU-specified laser reference. The comb is capable of supporting an Allan deviation of < 5 x 10-18 at 1 second and ~10-20 after 105 seconds. Add-on features include all fiber extensions to visible wavelengths corresponding to several atomic transitions. An integrated comb electronics package is currently under development.
-
Product
Plastic Wet Film Combs
154
-
Metric and Imperial values are on the same comb, 50 to 800μm on one side, 2 to 32mils on the other.
-
Product
Long Edge Wet Film Combs (Stainless Steel)
3238
-
Each comb has 24 measurement steps (teeth) providing a more accurate wet film thickness value.
-
Product
Phase Splitter Comb Generator
-
*Differential output - can also provide single ended outputs, one with positive going pulse, the second with negative going pulse. * Pulse height adjustable +1 to +5V peak into 50 ohms, on positive output, with concurrent -1 to -5V peak on negative output * Produces differential pulse on positive edge of input clock * Input clock may be 20-100MHz sinewave or 0.5-100MHz square wave, producing comb to 4GHz. Usable energy to >10GHz. * Differential outputs are designed to drive matched 50 ohm loads, but can drive any load, including short, without damage. Has integral fan. * Power Requirements: -12V @ 120mA and +18V @ 90mA.
-
Product
Comb Generators
-
Keysight comb generators provide excellent phase and amplitude flatness making them ideal for use in phase calibration applications. A customer selectable USB-controlled frequency divider which allows for broad range of input signal frequencies from 10 MHz to 67 GHz and small minimum tone spacing of 10 MHz, makes Keysight comb generators suitable for characterizing non-linear devices.
-
Product
Mini Fiber Optic, Patchcord, Receiver, 36", Multimode, 62.5/125, Single Ended
7-416804000-036
Fiber Optic Patchcord
Mini Fiber Optic, Patchcord, Receiver, 36", Multimode, 62.5/125, Single Ended.
-
Product
Reticles, Optical Slits, Optical Apertures
-
With over 30 years of experience in the manufacturing of high precision Reticles, Slits, Apertures, and Pinholes, APPLIED IMAGE has gained a reputation for delivering precise and accurate parts. We have supplied thousands of these parts to be used in Day/Night Sights, Binoculars, Targeting Systems, Telescopes, Tank Sights, Microscopes, and many other Bore-Sight devices.
-
Product
65 GHz Single Channel Optical Module
N1030A
Optical Module
The N1030A is a plug-in module for the DCA-X mainframe that can be configured with one 65 GHz optical channel, or one 65 GHz optical and one 95 GHz electrical channel.
-
Product
Mini Fiber Optic, Contact, Receiver, Polymer Optic Fiber
610113170
Fiber Optic Contact (Receiver)
This contact available for purchase as a patchcord only. Choose link below to configure as a patchcord. Primary mating contact 610113171. (May mate with other ITA contacts, as well.)
-
Product
Optical Transceivers
-
Based on Reflex Photonics technology, these rugged embedded transceivers offer bandwidth up to 300 Gbps in a chip-sized component. Designed for harsh environments including space, military, aerospace, and industrial applications, the transceivers provide high I/O density with low SWaP. Versions are available for mounting mid-board, front-panel, or on a VPX backplane (aligned with the SOSA™ technical standard).
-
Product
Optical Identification
-
Application areas of the 1D/2D code reader range from product tracking and product control to product identification.The sensor can read 1D and 2D codes regardless of their position. Even if up to 25% of the code information becomes damaged or soiled, it is still read correctly. The reader can also be used for optical character recognition (OCR), e.g. in order to identify products based on type labels or serial numbers.
-
Product
Comb Generator
CG118
-
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
Product
Optical Detector
LG-9200
-
The LG-9200 is a non-contact type optical detector which emits red visible light and detects the reflected light from the rotating shaft. The reflection mark is used for the detection by affixing it on the rotating shaft. It enables detection at an angle. (reflective mark: HT-011 by Ono Sokki)The LG-9200 has a built-in compact amplifier and outputs the square wave (voltage) after waveform shaping.With a compact and light weight body, performances are upgraded compared to the previous model LG-916.(LG-9200 detection distance: up to 40 mm, response speed: up to 40 m/s)
-
Product
Optical Square
10777A
Accessory Kit
The Keysight 10777A Optical Square, used with Keysight straightness measurement optics, adds squareness measurement capability to the Keysight5530 Laser Calibration System. The optical square measures the squareness of axes during laser calibration of a machine tool. The Keysight 10777A uses two accurately-aligned mirrors to direct an output beam at precisely 90 degrees to an input beam.
-
Product
Optical Profiler
DRK8090
-
Shandong Drick Instruments Co., Ltd.
This instrument uses noncontact, optical phase shift interferometry method does not damage the surface when measuring graphics can be quickly measured by a variety of three dimensional surface morphology, and analyzed to calculate the measurement results. Suitable for measuring a variety of blocks, the surface roughness of optical components; scale, dial the groove depth; magnetic (optical) disk, the head surface texture measurements; structural morphology of coating thickness and coating trough structure at the boundary of the grating; silicon surface roughness measurement and the graph structure and so on.
-
Product
Optical Switches
-
Thorlabs' optical switches are available for fiber-optic circuit integration or construction. We offer optical switches with integrated MEMS technology, optical switch kits, and PRO8 modules. Also available are optical switches for applications requiring an optical shutter in the 1500 - 1600 nm range.
-
Product
X-ray Optics
-
Do you want to shape your X-rays to a tiny point? Then our X-ray optics can help you. Benefit from 30 years of know-how in the development and manufacture of customized optical components for demanding applications. Our high-precision optics offer unsurpassed performance and enable the best results in a wide range of applications.
-
Product
Optical Link
OPT-2
-
The OPT-2 Optical Link allows the THERMES-USB to be operated with total optical isolation between THERMES and the host computer. USB Isolation device offers up to 4500 volts DC isolation.
-
Product
Optical Slits
-
The APPLIED IMAGE Optical Slit reticles are available in sizes from 10μm (0.01mm) to 1,000μm (1.0mm) widths, on either Chrome on Glass or Chrome on Opal material, with an overall size of 25.4mm (1.0 inch) diameter.
-
Product
Comb Generator
RefRad X
-
A comb generator is built inside a conical antenna element. Therefore no cable between antenna and generator is required. Thus leads to repeatable measurement results and reliable simulation of radiation performance.Optionally a fibre link for synchronisation with the receiver is used.Frequency Range 10 kHz - 3 GHzFrequency Spacing 10 kHz, 1 MHz, 5 MHz
-
Product
Optical Transmitter
ST1310-XX
-
Hangzhou Softel Optic Co., Ltd.
ST1310-XX Optical Transmitter adopts high linearity ORTOL DFB laser, build-in perfect pre-distortion adjustment circuit and laser APC,ATC closed loop control circuit. All the operating parameters are controlled by micro-processor, The LCD screen on the front panel can display relative operating status and the fault information.
-
Product
Wet Film Combs (Stainless Steel)
Elcometer 115
-
Four separate thickness ranges are available up to a maximum of 1,250μm or 50mils and are manufactured to an accuracy of ±5% of marked value or ±3µm (0.12mil), whichever is greater.
-
Product
Optical Benches
-
There are two types of SPHEREA optical test bench, Autonomous, to meet very specific needs, Combined with a versatile bench, to enable multiple-system testing.
-
Product
Optics
-
Optics and Photonics Simulation Software. Ansys Optics solutions offer robust design, optimization, and verification simulation software backed by world-class support. These tools empower designers to expedite the development of groundbreaking optical products while improving performance, reliability, and yield. With a suite of top-tier physics solvers, Ansys Optics provides user-friendly workflows for precise multiscale system design, from the nano to macro scale, enabling the design of diverse applications across various industries.
-
Product
Fiber Optics
-
The most complete line of Fiber Optic Products for end-to-end AV signal distribution over fiber optic cabling.
-
Product
Optical Sensors
-
Optical (Infra-Red) Proximity Switches with advanced and reliable technology for every application offer a flexible solution for automation, where other Proximity Switches can not perform. Optical Proximity Switches have distinct advantage of higher sensing distance over Inductive and Capacitive types.
-
Product
Optical Measurement
-
• Vertical optical measuring machine for static and dynamic measurement of various elements on small cylindrical parts.• The parts can be mounted between two centres or held in place using various accessories.• Attractive design and robust construction with many new features: New touch screen control panel for easy operation directly at the workplace, bi-telecentric optical system, high resolution CMOS camera, precision sliding headstock with integrated and protected daily standard, quick and easy accessory changing system, integrated temperature sensors, dynamic LED indicator of the general status of the measured part (GO/NG) and operator messages. Equipped with an exclusive optics tilting system.• Machines specially designed to measure threads such as, parallel, trapezoidal, conical, round, square, conical, worms, ball screws, bone screws, dental implants, etc.• Reflex SCAN+ concept for measuring parts without prior programming at the touch of a button• Delivered complete with a PC and the Reflex SCAN+ software, which allows a multitude of elements to be measured easily and intuitively.
