Automatic Test Systems
execute test program sets automatically. Also known as: ATS
See Also: Automatic Test Equipment, ATE Integrators
-
product
PIM Test Systems
AWT's Portable PIM testers are powerful yet compact tools for testing and analyzing telecommunications network infrastructure. These testers are ruggedized and can withstand harsh environmental conditions. they are accurate, reliable and easy to operate and they provide a wealth of features ideal for work in the field. Built-in Distance-to-PIM option.
-
product
In-Circuit Tester
Sparrow MTS 30
The Sparrow MTS 30 is a 19“ test system that can be integrated into any standard rack. The In-Circuit tester can also be used as benchtop test system. With this compact and flexible tester you can perform both analog and digital In-Circuit and functional tests.
-
product
Test Systems
6TL’s speciality is simplifying the architecture of test systems, so that our customer’s Total Cost Of Ownership is drastically minimized. The technology that conveys our mission is called FastATE.FastATE technology is based on using intelligent modules to build test systems.
-
product
Test Fixture (SMD Components)
16034E
Perform impedance evaluation on a minimum SMD size of 1.6(L) x 0.8(W) [mm]
-
product
E-mobility Test Systems
Correct contactingcharging cable detectionsecurity questionExtensive range of accessories for on-site measurements in a separate caseCharging cable with additional measuring lines (Sense)Convenient control through guided test procedure via WinSAM and tabletElectromechanical locking
-
product
Optics Test Systems
Electronic And Visual Autocollimators
Optik Elektronik Gerätetechnik GmbH
OEG GmbH specializes in the use of autocollimators, collimators and telescopes for special applications in optical measurement technology in the wavelength range from 380nm to 1550nm (SWIR).
-
product
High-Temperature Test Systems
HT-PEM (high-temperature polymer electrolyte membrane) technology represents a further development of PEM fuel cell technology. Unlike conventional PEM fuel cells, which operate at lower temperatures, HT-PEM fuel cells can reach temperatures of up to 200 °C.
-
product
Automatic Component Analyzer
TH2829C
Changzhou Tonghui Electronic Co., Ltd.
■ Freq: 20Hz-1MHz, resolution: 1mHz max. ■ Test Accuracy: 0.05% ■ Test Speed: 9ms ■ 800×RGB×480 7-inch TFT LCD display ■ Strongest signal source selection:
-
product
Laser Test Systems
Santa Barbara Infrared, Inc. offers an extensive family of test systems and components that test and characterize the performance of laser range finders, designators, illuminators and spot trackers.
-
product
Optics Test Systems
WAS 160: Wedge Angle Sensor
Optik Elektronik Gerätetechnik GmbH
Portable measuring head for wedge errors and radius of curvature, eg of car windshields, airplanes and helicopters. It can be used for any other glass panes.
-
product
Fully Automatic Plastic Tensile/Bending Testing Machine
This is a fully automatic tensile and bending tester for plastics. It is capable of continuous operation from measurement of specimen dimensions, supply, and data processing.
-
product
Automatic Double-Sided Bare PCB Final Inspection AVI System
FI-18 Series
InScan Limited (SIP) Co., Ltd.
InScan FI-18 is a compact and high performance fully automatic double sided AVI system for Final Inspection of PCB boards.The setup is based on golden board and CAD data which greatly simplifies the setup process. The FI-18 series inspects and processes a double sided board sized 210X300 mm 5.5 sec. Superior interline high resolution CCD sensor.
-
-
product
vibration test system
Labtone Test Equipment Co., LTD
Labtone EV series of electrodynamic shaker vibration test System simulate the vibration environment under the laboratory condition, and test the impact strength as well as reliability of various vibration test applications.Labtone EV series of electromagnetic vibration testing system simulate the vibration environment under the laboratory condition, and test the impact strength as well as reliability of various vibration test applications. In the laboratory, with the aid of vibration testing system, simulations of reproduction of sinusoidal, random, resonant search and dwell, classical shock and road models, etc. can be achieved. It is essential for product quality assurance, new product research and development.Labtone EV series of electromagnetic vibration testing system is specially designed to meet the need for long time operation. Vertical and horizontal vibrations can be achieved by the installation of vibration resistant base. The standard platform is equipped with high efficiency airbag shock isolation device, so that the vibration transmitted to the building can be minimized. There is no need for additional foundation in most of the cases.A complete set of vibration testing system is composed of shaker, power amplifier and vibration measuring control system, in accordance with the relevant national and international standards (such as: MIL-STD, DIN, ISO, ASTM, IEC, ISTA, GB, GJB, JIS, BS, etc.) to provide technical support for establishing product quality inspection.
-
product
Automatic Bias Controller
MATRIQ-IQABC
Optimizing DC bias points of an IQ modulator is no trivial task. There are six different Mach-Zehnder structures inside one dual polarization IQ modulator, all simultaneously influencing the properties of a single optical signal. Trying to optimize bias points using just the intensity measurement of the optical signal is time consuming, inaccurate and it requires a lot of knowledge and experience.
-
product
Automatic Transformer Test System
TH2829AX-24
Changzhou Tonghui Electronic Co., Ltd.
Number of Test PIN: 24 ■ Frequency: 20Hz-200kHz, Resolution: 0.5mHz ■ Signal Level: 5mV-2Vrms(Option:2mV-10Vrms) ■ Test Speed: max. 13ms ■ 7-inch TFT LCD display with a resolution of 800×RGB×480
-
product
Optics Test Systems
Front Window Scanner For Wedge Angle Measurement
Optik Elektronik Gerätetechnik GmbH
Scanning of complete automotive windshields to measure the wedge angle and thickness change, especially in the HUD area.
-
product
Automatic Battery
BATLV1200
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltageinstalations
-
product
Memory Test System
T5833/T5833ES
T5833 system is a cost-efficient, high-volume test solution capable of performing both wafer sort and final test of DRAM and NAND flash memory devices. Amid surging sales of mobile electronics, DRAMs, NAND flash memories and multi-chip packages (MCPs) — the main device types used in smart phones and tablets — are quickly evolving toward higher speeds and greater device capacity. Internet and cloud servers also are driving demand for faster, higher-capacity ICs. Yet the cost of testing today's wide array of memory devices is an obstacle for chipmakers, which urgently require solutions that can deliver high functionality, high performance and low cost of test (COT). Advantest's new, multifunctional T5833 memory test system meets these needs, delivering both wafer sort and final test capabilities for a full range of memory devices, including LPDDR3-DRAMs, high-speed NAND flash memories and next-generation non-volatile memory ICs.
-
product
SoC Test System
T2000
SoC devices require small-lot high-mix manufacturing methods in the present era of rapid generation change. Semiconductor makers struggle with requirements to replace their testers on a 2-3 year cycle. The T2000 addresses their needs by enabling rapid response to market needs with minimum capital investment.
-
product
Emissions Test System
PC-114
Perform Radiated & Conducted EMI pre-compliance testing at your facility up to 1 GHz. Com-Power PC-114 EMI emissions test system is a ideal solution performing pre-compliance EMC testing from 9 kHz - 1 GHz.. It has essential equipment needed for radiated and conducted EMI emissions measurements. The system includes a spectrum analyzer, antennas, near field probes, a preamplifier, LISN and a non conductive antenna tripod. Pre-compliance testing in EMC is a commonly used term not easy to define. In general, it implies testing done prior to formal testing for legal compliance. Formal legal compliance is performed at a facility designed and equipped with test instrumentation that is fully compliant with the applicable EMC standards. Such facility and instrumentation is capital intensive and can be expensive even to rent and not easily available. Compliance testing is performed per exacting requirements of the Standards and other reference documents adhering to the test methods and last detail. In addition, the test facility may require to be accredited by an accreditation body such as NVLAP, A2LA. Often it is desirable to know prior to compliance testing at such facility, whether a product is close to compliance and also how close. Pre-compliance testing is specially useful for specifications such as FCC, Part 15, EN 55022 or EN 55011 (CISPR 22 or CISPR11). Pre-compliance testing usually means using the full compliance methods but making a few educated compromises in use of site or equipment to reduce costs and testing time. Here are some benefits of pre-compliance testing.
-
product
Prototyping & Test Consulting Services Solutions
Don’t cut corners on the path to quality. We are experts in Design for Test (DFT), Design for Manufacturing (DFM), agile development, prototyping and standards/best practices in many industries. Speak to our prototyping and consulting services experts to ensure you make the right decisions and investments at the start of your project.
-
product
GT90 Dioxin+ Automatic Dioxin Sampling System
The GT90 Dioxin+ is designed specifically for an automatic and long-term sampling of dioxin emissions. The MCERTS certified system represents the cutting-edge technology for dioxin sampling and fulfills all requirements of the dioxin measurement standard. The system can be used in a variety of industrial processes such as waste incineration and cement production. Gasmet offers a full dioxin sampling solution package which consists of a system, lifetime service and support, documentation and training, and our expertise of over 30 years.
-
product
WEIGHING SYSTEM TESTING
1006
The Tester 1006 has a simultaneous control function of up to 4 load cells in any weighing system, upload and download function for programming the DAT and MC 302 series instruments, but it can also be used as a Calibrator and Peak detector. It is very useful for the correct mechanical installation and for fault diagnosis. The Tester 1006 is supplied as standard with cable for connection to our junction boxes / sum mod. CEM 4 / C and CGS 4 / C. Simultaneous display of the signal of each individual load cell allows to control the entire weighing system, weight distribution, overloads, faulty cells and faulty connections. OUT OF PRODUCTION. Pavone systems provides a new version of Tester 1006: Tester 1008.
-
product
Automatic Contacting Extensometry
AUTOX750
The Instron AutoX750 automatic contacting extensometer offers automated, high-precision strain measurement by motor-driven contact arms to engage specimens—eliminating manual setup while maintaining sub-micron accuracy over long travel. They integrate seamlessly with Instron testing frames and software to reduce operator error, speed cycle times, and ensure repeatable, standards-compliant strain data for metals, plastics, composites, and elastomers.
-
product
Engine Test Systems
Today''s engines and components require testing in a repeatable manner over a wide variety of conditions, ensuring that the final manufactured product consistently meets customer demands for performance and durability. The need for engines to be both economical and - above all - environmentally friendly, places fresh challenges on developers.
-
product
Automatic Calibration Module
ACM4509
ACM4509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full four-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to 18 connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
product
Mobile Measuring & Testing Systems
Individual testing tasks for technical plants and large machines often require the use of a large number of measuring instruments on site, which are difficult to network with each other and which, in the case of complex measurements, require a lot of experience and time in operating the measuring equipment and analysing the recorded measured values. The applications and possible uses can be quite different:
-
product
Portable Meter Test Systems
Zhengzhou SMS Electric Co.,Ltd
Portable energy meter calibration test devices.
-
product
Zero-distance Drop Test System
KRD40 series
KRD40 series drop tester, mainly simulates the resistance to drop and impact of large and heavy packaging products. Its strong power system and unique sample holder facilitate easy loading and unloading of oversized and overweight items and automatically rise to the setting. After the height, the drop test is completed. It can realize the drop test of the edge, surface and angle of the sample. This equipment is mainly used to evaluate the ability of product or packaging to withstand drops during transportation and loading and unloading, so as to improve product and packaging design.
