-
product
6-8 DB Directional Couplers From 0.5 To 40 GHz
Pulsar Microwave manufactures the CS06 and CS08 series single directional couplers in nominal values of 6 and 8 dB, respectively. These directional couplers are used in 50-ohm systems for narrow and wideband applications within 500 MHz to 40 GHz. Standard outlines are fitted with SMA or N type female connectors, but Pulsar Microwave can customize upon request.
-
product
6-Port PCI Express
PEX 8624
The ExpressLane™ PEX 8624 device offers 24 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 6 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 24-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including workstations, communications, storage, and embedded systems as well as intelligent I/O modules and add-in cards.
-
product
LXI Microwave Multiplexer, SP6T, 2-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-800-502
Our 60-800-502 is a 2 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Analog Earth Tester
FT3151
Earthing or grounding of electrical equipment is essential to maintain safety, protecting lives, as well as prevent damage to equipment. • Three-electrode method, Two-electrode method (Simple Measurement) • Wide measurement range for 0 to 1150 Ω, based on EN standard •Switchable measurement frequency to reduce the effects of power supply harmonics • Dramatically faster setup: Comes with improved grounding rods and cord winders. CAT II 300 V
-
product
PXI-4065, 6½-Digit, ±300 V PXI Digital Multimeter
780011-01
6½-Digit, ±300 V PXI Digital Multimeter—The PXI‑4065 is a 6½‑digit, 300 V DMM, which makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
product
USAF Targets
These targets conform to MIL-STD-150A. Frequencies change by the 6th root of 2. This target is also available in custom sizes and contrasts. This test target meets requirements as specified in MIL-STD-150A for resolving power tests. The target consists of a series of Elements having two sets of lines at right angles. Each set of lines consists of three lines separated by spaces equal to the line width. Each bar has a length to width ratio of 5:1. (Line width is equal to one half of line pitch, which is the inverse of line frequency.) Elements are arranged in groups of six each and Groups are arranged in pairs. Even numbered Groups occupy the left side and bottom right corner and contain a square feature having and edge length equal to the line length of Element 2 in that group. Odd numbered Groups occupy the top right corner and side. Groups and Elements are labeled and differentiated by numbering adjacent to their features. Frequencies in cycles/mm (c/mm) increase between each Element by the sixth root of two (approximately 12.25% per step). The general formula for the line frequency of any target Element can be expressed as 2Group+(Element-1)/6.
-
product
Relay Protection Test System
RELAYSTAR 1600
HAOMAI Electric Power Automation Co., LTD.
Relaystar-1600 the 6 phase universal relay protection test kit6-phase current (6×40A) + 6-phase voltage (6×150V) output.
-
product
Hand-held 3-Phase Meter Tester
6 Series
Powermetrix extends its revolutionary line of handheld three phase analyzers with the PowerMaster® 6 Series, now with Powermetrix Remote Manager (PRM)®. PRM enables wireless control of essential and various metering site accuracy tests contained within the PowerMaster 6 Series.
-
product
Zip Duplex Fiber Cable Stripper - TFS-304-2M
Shanghai Fibretool Technology Co.,Ltd.
1. This stripper is suitable for stripping duplex and multi-core Fiber Cables: 4 cores ×2.0mm DUPLEX cables, 2 cores ×3.0mm DUPLEX cables and 2 cores × MTP/MPO multi-core optical cables.2. 2~4 core cable can be stripped by one operation3. Cable stripping length is adjustable from 5 mm-42 mm4. All cutting surface are precision formed, hardened, tempered and anti-rust 5. The comfort anti-fatigue design handle ensures long-term workmanship 6. Length: 161 mm, weight: 145.50g
-
product
RF Bridge, 50 Ohm, 300 kHz to 6 GHz
86205A
The Keysight 86205A high directivity 50 ohm RF bridge offers unparalleled performance in a variety of general-purpose applications. It is ideal for accurate reflection measurements and signal leveling applications.
-
product
Industrial ATX Motherboard with 6th/7th Gen Intel® Core™ i7/i5/i3 Processor (Code name: Skylake/Kabylake)
IMB-M43
The ADLINK IMB-M43 is industry's first 6th/7th Gen Intel Core i7/i5/i3 Processor (formerly codenamed Skylake/Kabylake) based industrial ATX motherboard in the LGA1151 package with Intel Q170 Express chipset. The ADLINK IMB-M43 supports high-speed data transfer interfaces such as PCIe3.0, USB 3.0, and SATA 6 Gb/s (SATA III), with dual-channel DDR4 2133/2400 MHz memory up to 64 GB in four DIMM slots.
-
product
USB 2.0 SmartCable™ For ARINC429Test And Simulation
ASC429-x
USB 2.0 SmartCable™ for ARINC429 Test and Simulation with 6 channels (2Tx/4Rx) and 12 channels (4Tx/8Rx).
-
product
Replacement Solder Tip Lead Set for D410/D610
Dx10-SI
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
product
ENA Vector Network Analyzer
E5063A
2-port, 50 ohm, S-parameter test set Select the VNA frequency option that best suits your test needs and budget, and upgrade options at any time Boost efficiency and productivity with the consistent measurement framework of the industry-standard vector network analyzer Enhance your PCB manufacturing test capability with Option 011Easier operation with support for 6 languages via softkey & the embedded help manual in English/Simplified Chinese Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
PXI/PXIe RF Switch, Hex SPDT, 3GHz, 75Ω, MCX
42-830A-106
The 40-830A-106 (PXI) and 42-830A-106 (PXIe) are 75Ω RF switches with 6 separate SPDT relays slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
product
LGA 1700 Intel® 12th Gen. Core™ MicroATX Server Board with 4 x DDR5, 3 x PCIe (1 x Gen 5, 2 x Gen 4), 6 x USB 3.2, 5 x SATA3, Quad/Dual LANs, and IPMI
ASMB-588
- LGA 1700 Intel® 12th Gen. Core™ i9/i7/i5/i3 processors with W680 chipset- DDR5 ECC/Non-ECC 4400/4000/3600 MHz UDIMM up to 128 GB- One PCIe x16 (Gen 5) and two PCIe x4 (Gen 4) slots- Triple displays - DVI-D, VGA, and HDMI 2.0 ports- Five SATA 3 ports and six USB 3.2 ports- One M.2 2280 (PCIe x4)- Rackmount optimized placement with positive air flow design- 0 ~ 60 °C (32 ~ 140 °F) ambient operating temperature range
-
product
6 GHz ProBus2 Differential Probe with Dx10-SI Solder-In Tip
D610-A-PB2
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
product
Two Channel Cable
CONV1553-6
Two channels of dual-redundant 1553. Transitions from each SCSI-2 connector on a VME, VXI or CEI-600-6 front panel to four 18" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends, and D-Sub 9 pin connector for additional I/O.
-
product
LXI 75Ω 6:1 Microwave Multiplexer 16-bank 2.5GHz 1.6/5.6
60-820-016
Our 60-820 Microwave Multiplexer range is suitable for switching 75 ohm signals up to 2.5GHz. With the capability of supporting up to 16 banks of 6 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted DIN1.6/5.6 style connectors. A 50 ohm version, the 60-800, is also available covering frequencies to 20GHz.
-
product
Near Field Probes 30 MHz up to 6 GHz
XF1 set
The XF1 set of near field probes consists of 4 passive near field probes and one passive E field probe for making measurements in the development phase of the magnetic and electric fields in ranges from 30 MHz to 6 GHz. Due to their integrated impendance matching, the probes are less sensitive in the lower frequency range than the RF type probes. The probe heads of the XF1 set allow for the step by step identification of interference sources of the magnetic field on an electronic assembly. At first, for example the XF-R 400-1 detects the fields which the assembly emits in total. Next, using higher resolution probes the interference sources can be more precisely detected. The E field probe is used for the detection of electric interfering fields near the assemblies. With trained use of the near field probes, field orientation and field distribution can be detected. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
product
Power Supplies
CL-600B
Experience our new CL-series of power supplies. It has a 120mm Blue LED cooling fan for your gaming case & it has a 3 rail 12V output to fulfill all your system needs. 700W offer a 6+2 PCI-E ready for better graphics capabilities. Painted in black, the CL-series works great and looks great.
-
product
COM Express Type 6 Compact Module With 6th Gen Intel® Core™ I7/i5/i3 And Celeron® Processor
CEM501
The CEM501 COM Express Compact Type 6 module is based on the latest 14nm 6th generation Intel® Core™ i7/i5/i3 processors (codename: Skylake) with support for up to 32 GB dual channel DDR4 SO-DIMM memory. Featuring improved processing and graphics performance compared to the previous generation Intel® processor, the compact-size system on module CEM501 offers intense graphics performance and multitasking capabilities, making it ideal for telecommunication, medical imaging, digital signage, gaming machines, military, and IoT related applications.
-
product
Pressure Sensors
Whatever configuration you require, look to Sensata. Our devices span a spectrum of pressure ranges, configurations and form factors.High pressure (>750psi / 50bar)Micro Silicon Strain Gauge solutions provides rugged reliability and a hermetic seal for a wide variety of environmentsMid pressure (100 to 750psi / 6 to 50 bar)Ceramic capacitive or MEMS solutions offer a wide range of solutions tailored to application needs at superior valueLow pressure (inches of water to 100psi / 2mbar to 6 bar)MEMS solutions including TPMS offer extremely low power consumption and wireless connectivity
-
product
Open-Short-Load RF calibration kits
Open-Short-Load RF calibration kits from Fairview Microwave are available with Type N or 7/16 DIN connectors. Type N open-short-load RF calibration kits have male or female genders, 7/16 DIN open-short-load kits are male gender. Type N open-short-load (OSL) calibration kits for RF have a minimum frequency of 0 (DC) and a maximum frequency range between 4 GHz and 6 GHz. Type N open short load kits for calibration have a maximum power handling of between 1 Watt and 2 Watts.
-
product
Off-Line Base Test Platforms
To configure your Base Test Platform, the following parts can be added to the 6TL-19 bare half-rack:– Test Rack Manager, to control the test station.– Power Distribution Unit.– Uninterruptible Power Supply– Industrial PC or NI PXI to control the platform– 19’’ Monitor and keyboard with trackball– VPC Mass Interconnect Receiver (6 or 12 slots)– YAV Modules– Accessories: Beacon, Air inlet Pneumatic kit…– Any 19’ Instrument
-
product
PXI Quad 6:1 High Voltage Power MUX
40-331-003
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
product
Network Toner & Probe Kit
MT-7028
The MT-7028 lets you easily locate and verify the cable status and troubleshoot wiring for continuity, shorts, opens and crossover on RJ45 Lan cable Cat 55e67 (UTP/STP)RJ11/12 Telephone cable Cat. 3 (2/4/6 pin) & normal solid/Stranded wire by alligator clips patch cord. Ideal for all installation and maintenance fields of telecommunication, networking, datacom, Audio/Video, cable TV, and all weather cabling, etc.
-
product
Pico-ITX
RSB-3720
*NXP Arm® Cortex®-A53 i.MX8M Plus Quad/Dual up to 1.8 GHz*Onboard LPDDR4 4 GB / 6 GB, 4000MT/s memory*HDMI 1920x1080 at 60Hz, 1 Single or 1 Dual Channel 24 bit LVDS (or 1 4-Lane MIPI-DSI by BOM Option)*1 4-wire RS-232/422/485, 1 USB3.2 Gen1 By 1, 1 USB2.0, 1 Micro SD, 1 Mic. in / Line out*1 mini-PCIe for 3G/4G, 1 M.2 2230 Key E Slot*Supports Windows 10 IoT Enterprise on Arm, Yocto Linux BSP*Support I/O Expansions boards by UIO40-Express*Support Hailo-8™ AI accelerator module (up to 26TOPS)
-
product
Impedance Stabilization Network
Beijing KeHuan Century EMC Technology Co,.LTD
KH8158 is a device for measuring the common mode interference voltage of unshielded twisted pair cables. Cable testing according to CISPR 16-1-2. The equipment under test (EuT) and auxiliary equipment (AE) are directly connected to the corresponding ports. The port adopts RJ-45 socket (the distribution conforms to T568A/B.) This equipment is divided into three specifications: CAT3, CAT5, and CAT6, and the corresponding equipment is selected according to the cable model.
-
product
Replacement Solder tip lead set for D420/D620
Dx20-SI
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
