Variable Attenuators
Provide changeable resistance values.
-
Product
Digital Step Attenuators To 18 GHz
-
This family of digitally controlled switched bit attenuators have standard attenuation ranges of 32 dB and 64 dB, with 8 bits of resolution. LSB of 32 dB models is 0.125 dB, and for 64 dB models LSB is 0.250 dB. Attenuation level is obtained by 8 TTL control inputs.
-
Product
Variable Power Supply
VS3
-
The VS-3 power supply is a very convenient portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 3 amps, thus the name VS-3. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-3 is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case. A unique feature of the VS-3 is that it contains “Magnet Packs” on the back of the case. These “Magnet Packs” can support the VS-3 and allow it to “hang” from any magnetic metal surface. The VS-3 can be powered by our UPS system, eliminating the need for an extension cord. The ability to magnetically attach the VS-3 near the source of connection and eliminating the need for an extension cord makes the VS-3 a “must have tool” for technicians.
-
Product
Magnet & Integrated Variable Temperature Sample Space With DR Insert
-
Adapted MCK model DR inserted into 50 mm 1.6 K300 K VTI VTI cooling power used for condensing stage of DR Versatile solution as the magnet system can also be used with other inserts and measurement probes including He3, heated probes, rotator, VSM etc.
-
Product
10-amp AC and DC Variable Power Supply
ACDC-10
-
The ETI Model ACDC-10 is a small, lightweight, and portable AC and DC power supply. The unit is intended for resetting circuit breaker charging motors and other general-purpose applications. It will provide DC voltage in three nominal ranges from 0-120V, 240V, and 480V at 1 kVA, as well as AC voltage in three nominal ranges from 0-140V, 280V, and 560V at 1.4 kVA. The ACDC-10 is housed in a rugged plastic enclosure approximately 20” x 11” x 18” and weighs less than 65 lbs
-
Product
HVFO10X +/-40V (40x Attenuation) Universal Tip Accessory
HVFO100-40X-TIP-U
-
HVFO10X +/-40V (40x Attenuation) Universal Tip Accessory.
-
Product
HVFO10X +/-5V (5x Attenuation) Universal Tip Accessory
HVFO100-5X-TIP-U
-
HVFO10X +/-5V (5x Attenuation) Universal Tip Accessory.
-
Product
C-Band DWDM VGA with Mid-Stage Access Next-Generation Variable Gain EDFA
HWA4700 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4700 series is a next-generation variable gain EDFA, which with the most excellent performance and most completes functions in the market. It adopts nowadays most excellent optical performance, most advanced electronic technology and most complete software functions. Remarkable transient suppression control technology and heat management control technology let many complicated optical functions achieved. It is the most versatile multifunction optical amplifier in the market.
-
Product
Digital Attenuators
-
Macom Technology Solutions Holdings Inc.
Digital Step Attenuators (DSA)are offered in up to 6 Bit control with lowest step size of 0.5 dB covering DC to 40 GHz. MACOM's DSAs can be controlled with serial and parallel control allowing for best implementation for our customers. These products exhibit low insertion loss and high attenuation accuracy and are offered both GaAs and Silicon (SOI) processes and are offered in both packaged and bare die form factors.
-
Product
Direct Reading Attenuator with Remote Control
DA2XE
-
DA2XE Millimeter-Wave Direct Reading Attenuator is a measurement instrument for signal level setting or loss measurements in waveguide networks. It also can be used for calibration of other attenuation measurement instruments. Direct Reading Attenuators have rotary-vane design. The value of attenuation is determined by rotation angle of resistive film with respect to the waveguide channel. Attenuation value does not depend on frequency. The attenuator has electronic control. The attenuator can be used in local or remote (via USB 1.1 or higher) operation modes.The Attenuators are provided in waveguide bands between 18 GHz and 225 GHz.
-
Product
Manual Attenuator (Coaxial)
-
RF Lambda’s manual coaxial attenuators are used to control signal levels using a manual control knob or buttons. These are highly reliable and commonly used in test setups where the operator needs access to tune RF signals without the need for any digital or voltage control.
-
Product
Programmable Attenuators
-
a programmable attenuator from Pasternack. Our SMA attenuator is a programmable step attenuator design. This 50 Ohm adjustable attenuator is precision manufactured to RF and microwave industry specifications.
-
Product
Fixed Attenuators
-
ZTS provides 2 to 1000 Watts fixed attenuators with many types of connectors to choose from, maximum frequency would reach 67 GHz, we also provide custom or calibrated service as per your request.
-
Product
Attenuator Interconnect Kit, Type-N
11716A
-
Quickly and conveniently connect 1 dB step and 10 dB step attenuators together to achieve greater dynamic range with 1 dB steps. The Keysight 11716A interconnect kit contains a rigid RF cable, mounting bracket, and necessary hardware to connect any pair of Keysight 8494/5/6/7 attenuators in series. Attenuators must be ordered separately.
-
Product
Attenuators
-
OZ Optics offers a broad range of both variable and fixed attenuators having key competitive advantages. All of our attenuators operate over the two standard wavelength bands, the C-Band and the L-Band. This wide wavelength range makes these components ideal for DWDM applications. Our attenuators are wavelength insensitive, which means they operate with minimal changes in attenuation when used in either the C-Band or the L-Band and exhibit low return loss. In addition, all of our attenuators have a wide attenuation range, which means they operate at a wide range of power levels. This is important as increased power levels are being used in newer optical systems.
-
Product
POWER ATTENUATORS
TYPE ATF
-
National RF’s Type ATF Power Attenuators were designed to allow interfacing of linear power amplifiers to RF exciters, where a specific amount of drive to the amplifier is prescribed. Often, however, drive from the RF exciter exceeds this minimum prescribed level and some form of power attenuation must be used in order to not damage the input of the power amplifier. National RF’s type ATF-3 offers 3 dB of power attenuation (1/2 of the power) when used between the exciter and the amplifier and will handle an input power of 132 Watts, RMS (continuous power) while providing about 66 Watts RMS output power, when it is terminated into 50 ohms. In practice, the ATF-3 attenuator will handle exciters achieving Peak Envelope Power levels (PEP) in the area of 200 to 250 Watts while providing half of that power to the load. For less attenuation requirements, the ATF-1 and ATF-2 offer 1 and 2 dB of attenuation, respectively.
-
Product
Fixed Attenuators
-
BroadWave attenuators reduce the strength of an RF signal without appreciable distortion of its waveform.
-
-
Product
Attenuators And Pulse Limiters
-
A bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions. There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration an attenuator directly at the pulse generator output is inevitable.
-
Product
Fixed Attenuator (Waveguide)
-
RF Lambda’s fixed waveguide attenuators are used to attenuate RF signals with a waveguide interface. They come in a variety of different frequencies and power levels depending on the application.
-
-
Product
High Line Pressure Variable Reluctance Pressure Sensor to 10,000 psid
DP360/DP363
-
The DP360 can be calibrated for a full scale as low as ±50 psid while withstanding high static line pressure. Low differential pressure may be measured at static pressures as high as 10,000 psig with a maximum 3% FS zero shift error.
-
Product
Programmable Digital Attenuator
LDA-602EH
-
The LDA-602EH has a large attenuation range of 120 dB with an exceptional 0.1 dB step size, allowing for both precision and accuracy during fading tests or device characterizations. This attenuator also features a fast 15 us switching speed, an operating temperature from -30oC to 50oC, a maximum RF input of +28 dBm, and is priced at $875. The LDA602-EH operates with a low insertion loss of 9 dB to 6 GHz, an input IP3 of +55 dBm and a typical VSWR of 1.3:1. Easily programmed for ATE applications, the LDA digital attenuators are a cost effective solution whether you are in engineering, the production test lab, or in the field. Units are ROHS compliant and can be used with any PC or laptop computer with USB 2.0 port (or powered USB hub) and Windows operating system. Lab Brick Signal Generators are provided with easy to use Lab Brick GUI software, 32 and 64 bit API DLL files, LabVIEW and Linux compatible drivers.
-
Product
USB/Ethernet Control Step Attenuator
-
RF Lambda’s USB / ethernet control step attenuators utilize the same RF core as our standard digital attenuators only they incorporate a USB / ethernet controller to allow users to easily setup the control from any PC or network.
-
Product
Variable Pipe Frame Slide Anvil Type Outside Micrometer
-
Light-weight design using the pipe-structure frame Allows easy measurement of even a large workpiece.
-
Product
Digital Control Step Attenuator
-
RF Lambda’s digital control step attenuators are used to fine tune an RF signal using TTL control lines. Fast response time, various step sizes and overall attenuation ranges make these suitable for a variety of RF applications. Hermetically sealed options are available upon request.
-
Product
PXI Switchable-Input Programmable Step Attenuator Module, DC to 50 GHz
M9169E
-
The M9169E is a 3-port PXI programmable step attenuator module with a switchable path for a calibrator signal (cal input) into the input of a signal analyzer to improve amplitude accuracy. The M9169E has 0.03 dB insertion loss repeatability throughout the operating life of up to 5 million cycles per section. Its excellent attenuation accuracy across a wide operating temperature range ensures precise measurements.
-
Product
NI-5191, 800 MHz, ±30 V, 10X Attenuation, Differential Active Oscilloscope Probe
781785-01
-
The NI-5191 is a differential, active voltage probe that offers 800 MHz of input bandwidth with a 10:1 attenuation ratio. You can use it with oscilloscopes that provide 50 Ω input impedance. You can power the probe using a Type-N barrel power connector from a USB port or using a 9 V alkaline battery.
-
-
Product
HVFO10X +/-20V (20x Attenuation) Universal Tip Accessory
HVFO100-20X-TIP-U
-
HVFO10X +/-20V (20x Attenuation) Universal Tip Accessory.
-
Product
0-600 Amp Variable Carbon Pile Load Tester
6039
-
• Test batteries up to 1200 CCA• Fine threaded shaft for fine adjustment• Temperature compensation chart• Easy to read digital voltmeter & ammeter combine with the versatility of a carbon pile load• Spring loaded to shut-off automatically• Unique curved discs to prevent hot spots• Tests all battery types• Made in USA of US and Global Components
